Martec Discovery Series User manual

DISCOVERY
SERIES
Ceiling Fan Instrucon Book
Models: MDF124 MDF134 MDF1243 MDF1343
DESCRIPTION QUANTITY
Motor assembly 1
Instrucon manual 1
Screw kit 1
Balancing kit 1
Hanging bracket 1
Wall control kit 1
Blades 4

www.martecaustralia.com.au | 02 8778 7500 | [e-mail] Page 2
IMPORTANT
Always operate the product from a power source of the same Voltage, Frequency and rang
as on the product Idencaon Plate.
IMPORTANT
The fan is to be installed so that the blades are more than 2.1 metres above the oor.
Avoid contacng moving parts, keep hands, hair and clothing well away from the product while it is in
operaon.
A Luminaire (light ng) included in the fan packaging may only be ed to this fan.
“This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilies, or lack of experience or knowledge, unless they have been given supervision or
instrucon concerning use of the appliance by a person responsible for their safety.”
“Young children should be supervised at all mes to ensure that they do not play with the appliance.”
Do not operate any product which has been or appears damaged in any maer or aer the product
malfuncons.
Do not use the product for other than its intended use as described in these instrucons. This product
is intended for normal domesc household use only. The use of accessory aachments other than those
recommended by the manufacturer may cause safety hazards.
SAFETY
The installaon of fans must follow S.A.A. standards and meet local Authority regulaons. A fully qualied
and licensed electrician lawfully MUST carry out installaon. Means for disconnecon must be incorporated
in the xed wiring in accordance with wiring rules.
Fan and light MUST be earthed. Bracket MUST be rmly aached to a solid structure i.e. concrete ceiling,
steel structure or mber frame and addional joist MUST be nailed between beams if the mber opon is
required. ONLY install the remote controller kit that comes supplied by Martec Pty Ltd within package. DO
NOT control operaon of fan and light with any other remote control than what was approved by Martec Pty
Ltd and supplied within this package, as this will void warranty.
WARNING
Only approved Martec Pty Ltd wall controllers should be used for the operaon of our fans. The use of
unauthorised controllers will void the warranty. DO NOT mix blades from one fan to another. All blades
must be replaced if damaged.
Thank you for purchasing your MARTEC DISCOVERY Series Ceiling Fan. Please read all instrucons carefully
before assembly and use.
IMPORTANT SAFEGUARDS
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. KEEP
THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT INSTALL THE PRODUCT WHERE IT
CAN BE EXPOSED TO RAIN, MOISTURE OR ANY LIQUID.

www.martecaustralia.com.au | 02 8778 7500 | [e-mail] Page 3
With Light
Without Light
Wall Control
Blade
Cover
Cover
Reverse Switch
Housing
Rotang Ring
Light Plate
Glass
Hanging Plate
Hanging Ball
Down Rod
Canopy
Wall Control
Blade
Cover
Cover
Reverse Switch
Housing
Rotang Ring
Cover
Hanging Plate
Hanging Ball
Down Rod
Canopy

www.martecaustralia.com.au | 02 8778 7500 | [e-mail] Page 4
HOW TO ASSEMBLE
Secure the hanger bracket to ceiling beam or a suitable piece of mber inserted between the ceiling beams.
Martec Pty Ltd recommends the bracket to be aached with two long screws as supplied within the package.
Place circular shockproof gasket above the hanger bracket. Align the bracket and screw the hanger bracket to
the ceiling ghtly.(See Fig.1.)
Place fan into hanger bracket and align Ball Joint Slot with hanger bracket as illustrated.(See Fig.2.)
Aer wiring is completed, aach the canopy to the hanger bracket by pushing upwards and twisng an
clockwise. Locate screws in keyholes and ghten., ensuring canopy is not touching the ball joint. (See Fig.3)
HOW TO INSTALL BLADES
1.Remove the one screw from the covering plate of bladexing hole. (See Fig.4a)
2.Insert blades one at a me through four slots around the centre band and secure with three screws for
each blade through the top opening. Repeat this procedure for all blades. (See Fig.4b)
3.Replace the cover plate and secure with one screw once all four blades have been rmly ed.
Fig.4bFig.4a
Fig.3 Fig.4
Fig.2Fig.1
ball seat rubber cover
(Packed with hanger bracket)

www.martecaustralia.com.au | 02 8778 7500 | [e-mail] Page 5
3000k
4000k
5000k
HOW TO REMOVE THE SHADE FOR INSTALLING LED LIGHT PLATE
(Version with lights)
Remove the Glass Shade carefully as shown . Turn anclockwise to remove and clockwise to ghten the
glass shade. (See Fig.5.)
Tricolour CCT (Colour changeable temperature)
Please make sure the switch is o before changing the colour temperature. Simply ick the switch on the
LED plate (See Fig.6.) to select the desired colour temperature (3000K, 4000K or 5000K).
Dimming
The DISCOVERY fan has a smart 3 step dimming LED light
module which doesn’t require a dimmable remote control
or a wall dimmer. It only requires a normal on/o remote kit
(MPREM) or a normal light wall switch (supplied
as part of the wall controller in the box).
Turn the switch on and the light will turn on. Flick the switch
on/o within 1 second and the light output will
dim down to approx. 50%, ick the switch on/o again and
the light output will dim down to approximately
15%. The light kit has no memory funcon, it will turn on at
100% inially.
Fig.5
Fig.6

www.martecaustralia.com.au | 02 8778 7500 | [e-mail] Page 6
WIRING INSTRUCTIONS