Martec PRINCE MPAPP User manual

MARTEC PRINCE CEILING FAN REMOTE CONTROLLER OPERATION AND
INSTALLATION INSTRUCTIONS (MPAPP)
IMPORTANT
1. Read and save these instrucons.
2. Please note that all xed wiring appliances must be installed by a qualied electrician.
3. The supply to the remote-control receiver must be connected through a mains switch, i.e. exisng wall
switch, to isolate the power.
4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5. Install receiver into the ceiling fan canopy of the fan to ensure proper protecon (Do not install in ceiling
cavity as this will void warranty).
6. This unit is to be used for the control of a ceiling fan with a AC230/240V 50Hz power supply only.
7. Do not install in damp locaons or immerse into water (For indoor use only).
8. Do not pull on or cut leads shorter.
9. Do not drop or bump the unit.
10. Please ensure plugs are in the correct posion i.e. AC power input to the AC power and to the fan output
of the fan. If in the incorrect posion, receiver will be damaged, and will not be covered under warranty.
11. PLEASE NOTE: The baery will weaken with age and should be replaced regularly before leaking takes
place as this will damage the transmier. Dispose of used baery properly, keep the baery out of reach
of children. Leaking baeries are not covered under warranty.
12. CAUTION: To reduce the risk of re or injury, do not use this product in conjuncon with any variable (rheostat)
wall control.
www.martecaustralia.com.au | 02 8778 7500 | [email protected]
Once the connecon has been made,
the receiver inserts into the drop rod
hanging bracket. The canopy comes up
to cover the receiver and bracket.
CAUTION: When pung canopy of
the fan onto mounng bracket, please
ensure that wires are completely tucked
away to avoid canopy rupturing the
wires and causing a short circuit.
INSTALLATION INSTRUCTIONS
CAUTION! INCORRECT WIRE CONNECTION WILL DAMAGE THIS RECEIVER. PLEASE ENSURE 240V
IS TO INPUT AND MAKE SURE POWER IS COMPLETELY OFF WHEN INSTALLING THE RECIEVER
UNIT OR A VOLTAGE SURGE MAY BLOW THE CIRCUIT BOARD.

www.martecaustralia.com.au | 02 8778 7500 | [email protected]
LEARNING PROCESS (Programming)
TRANSMITTER
Download the FREE Martec OneTouch from the App
Store or Google Play today!
NOTE: The Hand Held Remote Control System is equipped with
a learning frequency funcon which has code combinaons to
prevent potenal interference from other remote units.
FUNCTIONS OF TRANSMITTER
Installaon of Transmier Wall
Mount Holder with two screws.
HIGH - Turn on the fan at high speed
MED - Turn on the fan at medium speed
LOW - Turn on the fan at low speed
OFF - Turn o the ceiling fan.
LIGHT ON/OFF Press and release immediately to turn on or o the
light (if the light is step dim enabled the light will drop one level).
1H TIMER - Ceiling fan will turn o aer 1 hour automacally.
2H TIMER - Ceiling fan will turn o aer 2 hours automacally.
4H TIMER - Ceiling fan will turn o aer 4 hours automacally.
8H TIMER - Ceiling fan will turn o aer 8 hours automacally.
LIGHT - Press light buon “on” and “o” repeatedly to operate the
light funcon of your ceiling fan lighng (if applicable).
Please note: The transmier can be programmed to one or more receivers, so during the programming
process, please refrain from aempng to program mulple receivers at the same me. Please ensure
power is switched o for all/any addional receivers that are installed in the same premises when wanng
to individually pair a desired transmier to a parcular receiver. Failure to ensure power is o for all other
receivers may result in the transmier being paired to all receivers instead.
Install the AAA 1.5V*2 baeries. Within 30 seconds of
turning the Receivers AC power ON. Press the transmier’s
“LEARN” key.
Hold the “LEARN” key for over 2 seconds, once the receiver
has detected the frequency, Light will ash 2 mes which
indicates that learning process nished.
The OneTouch app operates seamlessly with handheld remote
transmier to enable control of mulple compable Martec Ceiling Fans
with advanced mer funcon and security sengs.
• Turn on your smart phone or device’s Bluetooth sengs on
• Turn on the AC power of the ceiling fan with the remote-control kit installed
• Tap the “Done” icon on the Martec OneTouch app for pairing code. Fill in the
locaon name
• Martec OneTouch, convenience at your ngerps!
For detailed tutorial of the Martec OneTouch App Controller, visit our website for more informaon.
01
02
Martec OneTouch
FREE DOWNLOAD