Martem TELEM-AGC-L User manual

Street lighting controller TELEM-AGC-L
User Manual
Martem AS
2018

Contents
1. INTRODUCTION................................................................................................................................. 3
2. FEATURES ......................................................................................................................................... 3
3. TECHNICAL DATA............................................................................................................................. 4
4. TERMINAL CONNECTORS ............................................................................................................... 7
5. COMMUNICATION CABLES ............................................................................................................. 8
6. FIRMWARE UPDATE......................................................................................................................... 9
7. DIP SWITCHES................................................................................................................................. 10
8. INDICATION LED-S.......................................................................................................................... 10
9. CONFIGURATION TOOL................................................................................................................. 10
10. ORDER CODE ................................................................................................................................ 11
11. OPEN-SOURCE SOFTWARE INFORMATION ............................................................................. 11

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 3-
1. Introduction
TELEM-AGC-L is used as LCBC (Light Control Box Controller) in smart street
lighting solutions. The system is visualized by central map based user interface
software. TELEM-AGC-L is a good choice for solutions where older and newer
individually controlled LED luminaries are in same control network
2. Features
Autonomous control without need of permanent connection to control center
based on internal astronomical clock and sensors
GPRS communication via secure VPN channels
Integrated radio and gateway functionality for individually controlled luminaires
solution
Interfaces for energy meters and transducers
> 10 sec. operation after power outage for sending last signals
Astronomical clock
NTP time synchronization

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 4-
Logical operations between digital and analog signals
Alarms via SMS and e-mail
Web browser interface for control and maintenance
OpenVPN, IPsec, L2TP and SSH secure connections
Historical data recording
SNMP for monitoring
Various data exchange protocols via Ethernet and serial ports
An user friendly free configuration tool
Configurable remotely over communication line
Configuration export/import to/from CSV format files
Charger for external backup battery
3. Technical Data
Data communication protocols
To upper level systems:
IEC 60870-5-104
IEC 60870-5-101
Modbus-TCP (on development)
To lower level devices:
IEC 61850
IEC 60870-5-101 unbalanced
IEC 60870-5-103
IEC 60870-5-104
Modbus-RTU
Modbus-TCP
IEC 62056-21 (IEC 1107)
SPA-Bus
Communication ports can be freely configured for upper or lower level
communication.

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 5-
Interfaces on base board
Communication ports
GPRS modem
Optional radio network interface
Ethernet RJ45 connector, 1,5 kV isolation
2 x RS-232 with RJ9-4P4C connector, galvanically isolated, 15 kV
surge protection
RS-485, galvanically isolated, 15 kV surge protection
1-wire for environmental sensors
Photo and temperature resistor inputs
USB console port for maintenance
IO connectors
8 optically isolated digital inputs (wet contacts with internal supply)
4 relay outputs (max 0,5 A 250 VAC; 0,25 A 220 VDC)
Expansion modules
Module A
8 optically isolated digital inputs (wet contacts with internal supply)
4 relay outputs (max 0,5 A 250 VAC; 0,25 A 220 VDC)
Module B
8 optically isolated digital inputs (wet contacts with internal supply)
3 relay outputs (max 0,5 A 250 VAC; 0,25 A 220 VDC)
DALI master interface
Module F
16 optically isolated digital inputs (wet contacts with internal supply)
8 relay outputs (max 0,5 A 250 VAC; 0,25 A 220 VDC)
Module G
16 optically isolated digital inputs (wet contacts with internal supply)
7 relay outputs (max 0,5 A 250 VAC; 0,25 A 220 VDC)
DALI master interface

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 6-
Serial data communication parameters
1 start bit
Odd, even or no parity
Communication rates from 300 to 115200 bit/sec
Electrical characteristics of isolated input
Withstand to static discharge IEC 61000-4-2
Withstand to bursts, surges IEC 61000-4-4, 61000-4-5
Power frequency magnetic field IEC 61000-4-8
Voltage dips, variations IEC 61000-4-11
Mechanical parameters
Degree of protection IP 31
Dimensions (W x H x D) 65x155x190 mm
(with protruding parts)
Ambient temperature in operation –40°C…+70°C
Weight 900 g
Mounting DIN rail
Relative humidity 95% non-condensing
Radio frequency compatibility
RF emission IEC 55022 Class A
Immunity to RF fields IEC 61000-4-3, 61000-4-6
Power supply
Supply voltage range 230V AC
Power consumption < 7W

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 7-
4. Terminal Connectors
RJ9-4P4C
C2 RS232
– RS485
+ RS485
C3 GND C3 R485
1
C
2
C
3
C
4
C
RJ45
COMMON
DI 1
DI 2
DI 3
DI 4
Reset
Default Setup
C1&C2 GND 4
Tx 3
Rx 2
C1&C2 GND 1
C1&C2 GND 4
Tx 3
Rx 2
C1&C2 GND 1
Console
Modem
Run
Alert
Telem-AGC-L
MAIN BOARD, FRONT PANEL
DOWNSIDE
1-WIRESENSORSSIM 1
Radio
Modem
Antenna
GPRS
Antenna
13
C
14
C
15
C
16
C
COMMON
DI 13
DI 14
DI 15
DI 16
DO 6
DO 7
DO 8
9
C
10
C
11
C
12
C
DI 9
DI 10
DI 11
DI 12
DALI
or DO5
A
nc
B
21
C
22
C
23
C
24
C
COMMON
DI 21
DI 22
DI 23
DI 24
DO 9
DO 10
DO 11
DO 12
17
C
18
C
19
C
20
C
DI 17
DI 18
DI 19
DI 20
OPTIONAL INTERFACES
See order codes
UPSIDE
SD
C1 RS232
ETH 0
RJ9-4P4C
RJ9-4P4CRJ9-4P4C
DIGITAL INPUTS 8...5
DO 4 DO 3 DO 2
RELAY OUTPUTS 4...1
POWER
230VAC BATTERY
or OUTP.
12V 0,4A
- +
DI8 DI7 DI 6 DI 5
C 8 C 7 C 6 C 5
L N PE DO 1
or IFR

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 8-
5. Communication cables

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 9-
6. Firmware update
NB! Before updating to new firmware read the setup from your device, and
make a backup.
Run GWS.exe and set up SSH connection with the device
Press the Upd▼button next to R W C
buttons
If you have compressed .7z firmware update
file (provided by Martem AS) choose Update
From File
If you do not have .7z firmware update file choose Check martem.ee to
refresh exsisting firmware versions list for this AGC-L device
Press Update to feature and choose needed firmware version. Download is
starting...
After firmware is downloaded Confirm window appears. Press Yes button, the
update process starts
Wait until the device resumes to its normal operation state (RUN LED will start
slow blinking again)
Firmware update is complete.
Checking results of the firmware update operation:
Press Rbutton to read back the device setup data
Check the Version from GWS Status tab

AS Martem Street Lighting Controller TELEM-AGC-L User Manual Rev. 1 / 2018
AS MARTEM Tel: [phone] [email protected] www.martem.eu
- 10 -
7. DIP switches
Reset: Switch RESET to ON state and then back to OFF state for Reset operation
Dft. Set: To apply default setup:
1. Switch DFT. SET to ON state
*Alert indication LED starts blinking within 5 seconds
*Alert indication LED will blink for 2 seconds
2. Switch DFT. SET back to OFF state when the alert indication LED is
blinking to apply default setup
*If DFT. SET is switched back to OFF state when the alert indication LED is not
blinking, default setup will NOT be applied
8. Indication LED-s
MODEM –green LED –indicates the 4G, 3G, 2G modem network connection
RUN –green LED –blinking green indicates that the program is running
ALERT –red LED –failure
Green LED-s for serial communication ports for RX, TX indication.
9. Configuration tool
The Telem-AGC device is configured with Telem-GWS software.
The configuration process is described in Telem-GWS software manual.