Martin Audio C516 User manual

CONTENTS (ENGLISH) Page No
1 INTRODUCTION 2
2 UNPACKING 2
2.1 Contents of a 1-pack 2
3 CEILING TYPE 3
3.1 Optional support rails 3
3.2 Rigid ceiling tiles 3
3.3 Soft ceiling tiles 3
3.4 Fixed ceilings 3
3.5 Cutting the mounting hole 3
4 INSTALLATION 4
4.1 First fix 4
4.2 Second fix 6
5 TRANSFORMER VERSIONS 7
6 PAINTING THE LOUDSPEAKER 7
7 WARRANTY 7
8 TECHNICAL SPECIFICATIONS 8
Martin Audio – C516 Ceiling Loudspeaker
MARTIN AUDIO
LONDON
The Martin Experience
CONTENTS
<
>
PRINT
GUIDES

1 INTRODUCTION
Thank you for purchasing a Martin Audio C516 ceiling loudspeaker. This is
a versatile flush-mount loudspeaker designed for high quality music and
speech reproduction in distributed sound systems. It has been styled to
present a discrete, high quality appearance which will blend unobtrusively
into commercial and architectural environments.
It features a 6.5" (160mm) 2-way drive unit utilising patented ICT™
(Inductively Coupled Transducer) technology. This size of driver has been
chosen to optimise the conflicting requirements of low frequency extension
and high frequency dispersion.
The C516 is available in the following electrical configurations:
C516 4 ohm
C516T 100V line (Europe and Japan)/ 70V line (USA)
2 UNPACKING
Each C516 is built to the highest standard and thoroughly tested before it
leaves the factory. After unpacking the loudspeaker, examine it carefully for
any signs of transit damage and inform your dealer if any such damage is
found. Check that the electrical configuration supplied (4 ohm, 70/100V
line) is the one you require. It is suggested that you retain the original
packaging so that the speakers can be repacked and returned if necessary.
Please note that Martin Audio and its distributors cannot accept
responsibility for damage to any returned product through the use of non-
approved packaging.
2.1 Contents of A 1-pack
1 loudspeaker baffle
1 back-can (complete with steel strip spring)
1 support bracket + wing nut
Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
2
This equipment conforms to the requirements of the
EMC Directive 89/336/EEC, amended by 92/31/EEC
and 93/68/EEC and the requirements of the Low
Voltage Directive 73/23/EEC, amended by 93/68/EEC.
Standards Applied EMC Emission EN55103-1:1996
Immunity EN55103-2:1996
Electrical Safety EN60065:1993
CONTENTS
<
>
PRINT
GUIDES

3 CEILING TYPE
Before beginning the installation, it is important to evaluate the construction
of the ceiling. The type of ceiling will affect the installation procedure and
method of connection. It will also determine whether optional support rails
(see Section 3.1) are required. A qualified person such as a building
professional, architect or qualified engineer should make these
determinations.
3.1 Optional support rails
Some ceilings or ceiling tiles may not be strong enough to support the
weight of the speaker without support rails. Whether a ceiling alone is
strong enough to support the weight of the loudspeaker should be
determined by a qualified person such as a building professional or
architect. Optional support rails for the C516 are available from your
dealer.
3.2 Rigid ceiling tiles
Rigid ceiling tiles will normally not require additional support rails, though
these may be deemed necessary if the tiles are likely to be degraded by
moisture.
3.3 Soft ceiling tiles
Soft ceiling tiles will usually require the use of additional support rails since
they may not always support the weight of the loudspeaker.
3.4 Fixed ceilings
Installation of the C516 can be performed without access to the rear of the
ceiling, making it also suitable for use in fixed ceilings.
3.5 Cutting the mounting hole
Cut the mounting hole in the ceiling or tile. The hole required for the C516
is 212mm(8.3”) diameter. The back-can requires a clearance height of at
least 160mm(6.3”) from the rear surface of the ceiling.
Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
3
CONTENTS
<
>
PRINT
GUIDES

4 INSTALLATION
The C516 is installed in 2 stages:
First fix: Make electrical connections and install back-
can in the ceiling
Second fix: Install speaker baffle
4.1 First fix
Note: The back-can of the C516 is provided with two 20mm holes. One
hole is fitted with a grommet which accepts cables with diameters of
7-10mm and provides light strain relief (see Fig. 1). The other 20mm hole
is fitted with a blanking plug.
IMPORTANT
Please note that is very important for the acoustic performance of the
C516 that the back-can remains airtight after installation. If the
grommet and blanking plug are removed and other cable glands
utilised, these should be airtight.
Depending on local electrical codes, flexible metallic tubing or conduit may
have to be used in conjunction with metal cable glands.
1. The terminal block within the back-can will accept stripped wires. To
prepare the wires for connection, strip back approximately 8mm.
2. Pull the steel strip spring in the back-can to its down position.
3. Insert the stripped wires into push-terminal block in back-can. Please
note that it is important to maintain consistent polarity throughout.
4. If support rails are to be used feed them up through the ceiling cut-out
and place them in parallel positions on either side of the cut-out.
Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
4
Fig. 1
CONTENTS
<
>
PRINT
GUIDES

5. Put the support bracket through the ceiling cut-out and stand it up on
the ceiling rear surface. If support rails are used, place the feet over
the rails (see Fig. 2).
6. Push the back-can up through the cut-out and locate the hole in the rear
of the back-can on the stud at the centre of the support bracket
(see Fig. 3).
7. Tighten the wing nut on the stud. This will sandwich the ceiling between
the support bracket and the front lip of the can.
Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
5
ø212mm
Fig. 2
Fig. 3
CONTENTS
<
>
PRINT
GUIDES

4.2 Second fix
1. Attach the safety wire between the back can and loudspeaker baffle
with a screwdriver.
2. With the steel strip spring in its down position, insert the stud attached to
the loudspeaker magnet through the hole in the strip spring (see Fig. 4).
3. Push the retaining clip through the small hole in the stud.
4. Attach the spade terminals to the loudspeaker. The brown wire should
be connected to the + terminal, the blue wire to the - terminal.
5. Rotate the baffle slightly so that the port is clear of the spring and will
not foul it. Gently push the baffle upwards (see Fig. 5). The spring
action will draw the baffle into the can once past its initial resistance.
Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
6
Fig. 4
Fig. 5
CONTENTS
<
>
PRINT
GUIDES

5 TRANSFORMER VERSIONS
‘T’versions of the C516 have a transformer mounted in the back of the can.
3.7w, 7.5w, 15w, and 30w taps are available for 70v and 100v line systems.
The appropriate taps may be selected by changing a spade link on the p.c.b.
The PCB mounted terminal blocks on the transformer assembly will accept
stripped wires up to 2.5mm2and has a loop out, input link facility. To prepare
the wires for connection, strip back approximately 8mm.
Insert the stripped wires into the terminal blocks by sliding the yellow lever
towards the spade terminals. Please note that it is important to maintain
consistent polarity throughout.
6 PAINTING THE LOUDSPEAKER
Both the outer rim and grille of the C516 may be painted if required and the
grille can be removed to make this easier. If the grille is to be painted, it is
important that a spray can is used rather than a brush, as this will tend to clog
the holes. Please note that Martin Audio cannot accept responsibility for the
quality of finish obtained
7 WARRANTY
Martin Audio C516 Ceiling Loudspeaker is warranted against manufacturing
defects in materials or craftsmanship over a period of 5 years from the date of
original purchase. During the warranty period Martin Audio will, at it's
discretion, either repair or replace products which prove to be defective
provided that the product is returned in its original packaging, shipping prepaid,
to an authorised Martin Audio service agent or distributor.
Martin Audio Ltd. cannot be held responsible for defects caused by
unauthorised modifications, improper use, negligence, exposure to inclement
weather conditions, act of God or accident, or any use of this product that is
not in accordance with the instructions provided by Martin Audio.
Martin Audio is not liable for consequential damages.
This warranty is exclusive and no other warranty is expressed or implied.
This warranty does not affect your statutory rights.
Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
7
100V 3.7W
70V 3.7W
70V 7.5W
100V 30W
70V 30W PRI
COM
70V 15W
100V 15W
100V 7.5W
COM
4 O HM
8 O HM
INPUT
INPUT
LINK
LINE
MATCHING
BOARD
ISSUE 1
4OHM
8OHM
COM
30W
30W
15W
15W
7.5W7.5W
7.5W
3.7W
3.7W
+
+
–
–
CMARTIN AUDIO LTD 2000
70V 100V
Fig 6
CONTENTS
<
>
PRINT
GUIDES

Martin Audio – C516 Ceiling Loudspeaker
ENGLISH
8
8 TECHNICAL SPECIFICATIONS
C516
TYPE Ceiling Mounted, two-way ICT™
vented baffle
FREQUENCY 80Hz –20kHz
RESPONSE 120Hz –20kHz ± 3dB
DRIVER 1 x 6.5" (160mm) full-range ICT™
RATED POWER 50W AES, 200W peak
RECOMMENDED 50-200W into 4 ohms
AMPLIFIER
SENSITIVITY 88dB (1 watt @ 1 metre)
MAXIMUM SPL 105dB continuous, 111dB peak
IMPEDANCE 4 ohms
DISPERSION (-6dB) 90 degree conical
FINISH Bezel & grille –white
PROTECTIVE GRILLE Expanded metal mesh
CONNECTORS 20mm gland in backcan
OPTIONS 30w line transformer
Tile support rails
DIMENSIONS (OD) 240mm x (D) 180mm
(OD) 9.6ins x (D) 7.1ins
WEIGHT C516 2kg (4.4lbs)
WEIGHT C516T 2.7kg (6lbs)
SHIPPING DIMENSIONS (W) 300mm x (H) 200mm x (D) 300mm
(W) 11.8ins x (H) 7.9ins x (D) 11.8ins
SHIPPING WEIGHT C516 2.5kg (5.5lbs)
SHIPPING WEIGHT C516T 3.2kg (7.1lbs)
Due to our policy of continuous improvement all specifications are subject
to change without notice.
CONTENTS
<
>
PRINT
GUIDES

C516 Ceiling Loudspeaker
Century Point, Halifax Road, Cressex Business Park, High Wycombe, Buckinghamshire HP12 3SL, England.
Telephone: [phone] Facsimile: [phone]
Web: www.martin-audio.com E-mail: [email protected]
The Martin Experience
MARTIN AUDIO
LONDON
Please Click here to
return to main menu
Please Click here to
visit our website
CONTENTS
<
>
PRINT
GUIDES

MARTIN AUDIO
LONDON
The Martin Experience
ENGLISH
C516 Ceiling Loudspeaker
User’s Guide
CONTENTS
<
PRINT
GUIDES
>