Martin Professional Exterior 200 User manual

Exterior 200
user manual

Measurements are in millimeters
290
112
165
402
242
262
310
301
© 2001 Martin Professional A/S, Denmark.
All rights reserved. No part of this manual may be reproduced, in any form or by any means, with-
out permission in writing from Martin Professional A/S, Denmark.
Printed in Denmark.
P/N 35000096, Rev D

3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fastening method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fixture orientation and location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bracket adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Data link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Control address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Personality settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
General operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
General guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
The LEDs and fixture operating status. . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Programming fixtures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Executing stand-alone scenes with an MC-X Controller . . . . . . . . . . . . . .26
Controller operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Lamp control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Color matching Exterior 200s and 600s . . . . . . . . . . . . . . . . 30
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Lens options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Changing the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Seal maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Lamp replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Firmware updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Fuse replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
DMX protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
MP-2 control menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

4 Introduction
I NTRODUCTION 1
Thank you for selecting the Martin Exterior 200. The Exterior 200 is an
automated 150 watt color-changing floodlight designed for fixed exterior
installation. It features seamless cyan, magenta, yellow (CMY) color mixing
and full-range continuous dimming. The fixture may be operated with DMX
controllers or in stand-alone mode with programmable start and stop times
or light levels.
The Exterior 200’s field angle with the standard lens 70°. Accessory lenses
are available to provide a narrow 36° field or an asymmetric 90° by 70° field.
SAFETY INFORMATION
Warning! This product is not for household use.
This product presents risks of lethal or severe injury due to fire and heat,
electric shock, ultraviolet radiation, lamp explosion, and falls. Read this
manual before powering or installing the fixture, follow the safety
precautions listed below and observe all warnings in this manual and on the
fixture. If you have questions about how to operate the fixture safely, please
contact your Martin dealer or call the Martin 24-hour service hotline at +45
70 200 201.
Guarding against electric shock
• Disconnect the fixture from AC power before removing or installing the
lamp, fuses, or any part.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault protection.
• Refer all service to a Martin service technician.
Preventing UV radiation and lamp explosion
• Never operate the fixture with missing or damaged lenses and/or covers.
• When replacing the lamp, allow the fixture to cool for at least 15 minutes
before opening the fixture.

Introduction 5
• Do not stare directly into the light. Never look at an exposed lamp while it is
lit.
• Replace the lamp if it becomes defective or worn out.
Guarding against burns and fire
• Never attempt to bypass the thermostatic switch or fuses. Always replace
defective fuses with ones of the specified type and rating.
• Keep all combustible materials (for example fabric, wood, paper) at least 1
meter (39 inches) away from the fixture. Keep flammable materials well
away from the fixture.
• Do not illuminate surfaces within 0.5 meters (20 inches) of the fixture.
• Install the fixture outdoors or in a well ventilated area.
• Never place filters or other materials over the lens.
• The exterior of the fixture becomes very hot, up to 90° C (194° F) during
normal operation. Do not locate the fixture in areas where accidental contact
is likely.
• Do not modify the fixture or install other than genuine Martin parts.
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C
(104° F).
Preventing injury due to falls
• When suspending the fixture above ground level, verify that the structure
can hold at least 10 times the weight of all installed devices.
• Block access below the work area whenever installing or removing the
fixture.

6 Installation
I NSTALLATION 2
This section describes in general terms how to mount the fixture and
connect it to data and AC power. These procedures shall be performed by
qualified professionals.
UNPACKING
The Exterior 200 comes with the following items:
• Philips CDM-SA/T 150 W discharge lamp (installed)
• User manual
FASTENING METHOD
Notice! It is the installer’s responsibility to determine the anchoring
method.
The Exterior 200 may be permanently fastened to any flat surface, pedestal,
or other support that can safely bear at least 10 times the fixture’s weight.
200
Ø53
82
Ø13 9
60
90°

Installation 7
The mounting bracket provides 3 holes for 12 mm (1/2 in.) hardware,
spaced 100 mm on center, and 2 quarter-circle slots with a center radius of
26.5 mm for 8 mm (5/16 in.) hardware.
Consult a qualified engineer to determine a suitable anchoring method. The
specific fastening hardware will depend on the installation. In general, use
high quality metric grade 8.8 or better corrosion resistant screws such as
zinc-plated steel, and self-locking nuts or lock-washers to secure the fixture.
FIXTURE ORIENTATION AND LOCATION
When choosing a location for the fixture, consider that it has an ingress
protection rating of 65. This means that the fixture is totally dust proof and
that it is protected from water ingression to the level that moisture from low-
pressure water jets from any direction cannot get into the product. However,
the product is not designed to withstand:
• High-pressure water jets from any direction
• Immersion in water (or any other fluid)
Do not bury the Exterior 200 or otherwise locate it in an unventilated space.
Install the fixture in a location where it is
• at least 0.5 meters (20 inches) away from the surface to be illuminated,
• at least 1 meter away from any combustible materials, and
• away from accidental public contact.
If the fixture points down, it must be installed with the power section over the
lamp section as shown so that water cannot collect between the lamp
section and the power section.
When the fixture is located above the area to be illuminated, install with
the power section on top.

8 Installation
BRACKET ADJUSTMENT
The mounting bracket can be positioned along the length of the power
section and pivots +70/-210 degrees from the 6 o’clock position shown
inside front cover.
This procedure requires 4 mm and 5 mm Allen wrenches (hex keys).
Warning! Allow the fixture to cool before handling.
To adjust the mounting bracket:
1 To adjust the bracket’s lateral position, remove the outer discs on each side
of the bracket. Loosen, but do not remove, the bracket screws. Slide the
fixture to the desired position and retighten the bracket screws. Replace the
outer discs.
2 To adjust the tilt angle, loosen the tilt-lock screws. Turn the fixture to the
desired angle and retighten the screws.
AC POWER
Do not connect the Exterior 200 to an electrical dimmer system: doing so
can damage the electronics.
Warning! Disconnect the fixture from AC power before removing any
cover.
Important! Verify voltage and frequency settings before applying power.
outer disc
bracket screws
tilt-lock screws

Installation 9
Power supply settings
The Exterior 200 is factory-wired to one of the configurations shown in Table
1. The model number and factory settings are printed on the serial number
label. If your local AC voltage or frequency differ from the settings for your
model, the fixture’s power supply must be rewired by a qualified installer or
technician.
Changing the power supply settings
1 Verify that the Exterior 200 is isolated from AC power. Remove the rear
cover.
2 Find the correct transformer setting for the local AC voltage in Table 2. Move
the brown transformer wire to the tap listed for the setting.
Model No. Voltage Frequency
90509000 230 V 50 Hz
90509002 245 V 50 Hz
90509004 210 V 60 Hz
Table 1: Default Power Supply Settings
Transformer:
Move brown wire to
change AC voltage setting.
Ballast:
Move black wire to change
AC frequency setting.

10 Installation
3 Set the correct AC frequency on the
ballast (located on the back of the
rear cover) by moving the black
ballast wire to the 50 or 60 Hz
terminal. (To release the wire, insert
a screwdriver in the hole next to the
terminal.) Make sure the wire is
securely connected.
4 Replace the rear cover before
applying power. See “Gaskets” on
page 33.
Mains connection
Warning! For protection from dangerous electric shock, the fixture must
be grounded (earthed). The AC mains supply shall be fitted with
a fuse or circuit breaker, ground-fault protection, and a means
to isolate the fixture from the mains during service or when not
in use.
The fixture is supplied with a weatherproof power cable.
However, note that if there is a breach or cut at any point along
the power cable (for example at a connection point), and if this
is exposed to water, moisture can be drawn up the inside of the
cables due to the vacuum effect from the heat generated during
operation. When installing the product outdoors, always ensure
that the fixture is protected from water ingression from inside
its power cable by:
• Protecting the connectors on the power cables in a weatherproof
housing, or a weatherproof electrical junction box, or
• Using IP65 rated cord caps, or
AC Mains
voltage
Transforme
r setting
Tap, brown
wire
Tap, white
& blue
wires
Tap, black
wire
190 - 202 V 195 V 11
914
203 - 217 V 210 V 12
218 - 235 V 225 V 14
236 - 252 V 245 V 15
269 - 285 V 277 V 16
Table 2: Transformer Primary Taps
brown wire
60 Hz
50 Hz
To set the frequency, move the
black wire to the 50 or 60 Hz
terminal.
black wire

Installation 11
• Replacing the supplied cable with one that connects directly inside the
fixture.
The Exterior 200 is equipped with a 1.8-meter (5.9 ft.) length of 3-conductor
0.75 mm2(~18 AWG) weatherproof electrical cable for connection to the AC
power supply. The cable enters the fixture through a cable gland that fits 5.5
- 10 mm diameter cables. The cable attaches with 1/4” female spade plugs
on the live and neutral wires and a ring terminal on the ground wire.
Replacing the mains lead
Other cable can be installed as follows.
1 Isolate the fixture from AC power.
2 Loosen both cable gland cap nuts and remove the power section cover.
Disconnect the existing mains cable and pull it through the cable gland.
3 Pass the new cable through the cable gland and connect the leads. The live
wire connects to PL3, the neutral wire connects to PL1, and the ground wire
connects to the chassis screw terminal.
4 Draw up the slack in the AC and data cables and replace the power section
cover. Tighten the cable gland cap nuts well to seal against moisture.
Installing a cord cap on the mains lead
A non-IP-rated cord cap may be installed on the mains lead for testing,
service, and temporary applications. For outdoor installations an IP65-rated
cord cap can be used.
Following the cord cap manufacturer’s instructions, connect the yellow and
green wire to ground (earth), the brown wire to live, and the blue wire to
neutral. Table 3 shows some pin identification schemes; consult an
electrician if you have any doubts about proper installation.
Wire (EU) Wire (US) Pin Marking Screw (US)
brown black live “L” yellow or
brass
blue white neutral “N” silver
yellow/green green ground green
Table 3: Cord Cap Connections

12 Installation
DATA LINK
A data link is required for DMX controller operation, and for synchronized
stand-alone operation of multiple Exterior 200s.
Cable and junctions
The Exterior 200 provides a dual 1.8 meter (5.9 ft.) 24 AWG cable with
locking 3-pin male and female XLR connectors for data connection. The
male cable is the data input and the female cable is the data output. The
connectors are wired pin 1 to shield (gnd.), pin 2 to signal - (cold), and pin 3
to signal + (hot).
Use RS-485 data cable designed for outdoor use to extend the link. RS-485
cable has low capacitance and a characteristic impedance of 85 to 150
ohms. It is electrically shielded and has at least 1 twisted-pair of conductors.
The minimum wire size is 0.2 mm2(24 AWG) for runs up to 300 meters
(1000 ft.) and 0.322 mm2(26 AWG) for runs up 500 meters (1640 ft.).
Warning! The fixture is not supplied with a weatherproof XLR connectors.
If these connectors are exposed to water, moisture can be
drawn up the inside of the cables due to the vacuum effect from
the heat generated during operation. When installing the
product outdoors, always ensure that the fixture is protected
from water ingression from inside its data cable by:
• Protecting the connectors on the data cable in a weatherproof housing
(or a weatherproof electrical junction box), or
• Using IP65 rated XLR cable and connectors (such as those produced
by Neutrik), or
•Replacing the supplied cable with one that connects
directly inside the fixture. This option requires a new
cable gland, see “Cable glands” on page 33. The
leads connect to the main circuit board as shown to
right.
ground
hot (white)
cold
not used
PCB data
connections

Installation 13
Adaptors
Adaptors may be required to connect the Exterior 200 to the controller or
other 5-pin devices. Adaptor cables for indoor use are available from Martin.
The adaptor cables are wired as shown below.
Splitter/Amplifiers
A device such as the Martin 4-Channel Opto-Isolated RS-485
Splitter/Amplifier may be used to branch the data link and/or extend its
length. Do not use a “Y” connector to split the link.
Terminators
Termination of the data link is required for trouble-free communication. For
temporary installations, this can be achieved with a male termination plug
inserted into the data output cable of the last fixture in each chain. A
termination plug is simply an XLR connector with a 120 ohm resistor
soldered across pins 2 and 3.
For permanent terminations, the link can be terminated with a 120 ohm
resistor across the hot and cold data terminals at the main circuit board
inside the last fixture in each chain.
Building a data link
To build a data link:
1 Connect a data cable to the controller’s data output. A male 5-pin to female
3-pin adaptor may be required. Lead the data cable from the controller to
the first fixture and plug it into the male data cable.
2 Connect the output of the fixture closest to the controller to the input of the
next fixture. Continue in this manner. Up to 32 fixtures may be connected
output to input.
3 Terminate the link as described above, at the output of the last fixture in the
chain.
Adaptor
Male Female
1
2
3
4
5
1
2
3
5-pin to 3-pin
P/N 11820005
Adaptor
Male Female
1
2
3
1
2
3
4
5
3-pin to 5-pin
P/N 11820004

14 Settings
S ETTINGS 3
This section describes how to set the control address, personalities, and
clock. To set user options you need a Martin MP-2 Uploader that has been
loaded with the Exterior 200’s control software and connected to the fixture
or data link. Please refer to the MP-2 Uploader user manual for details.
Note: Fixtures do not provide feedback to the uploader. Therefore, the
current settings can only be read by observing the behavior of the fixture.
MODES
The uploader provides two ways to access fixtures: single-fixture mode and
all-fixtures mode. In single-fixture mode, the uploader communicates only
with the fixture at a designated address. In all-fixtures mode, the uploader
communicates with all fixtures, of the same type, to which it is connected.
Fixture-specific settings such as the control address should be made in
single-fixture mode. If no other fixtures are connected, however, then all-
fixtures mode may be used. Global settings are made easiest in all-fixtures
mode.
CONTROL ADDRESS
The control address, also known as the start channel, is the first channel
used to receive instructions from the controller. Each fixture needs its own
control address set, and uses this address and subsequent control channels
to receive instructions from a controller. The Exterior 200 uses seven control
channels.
The control address, also known as the start channel, is the first channel
used. The Exterior 200 uses seven channels of control data. It reads the
data on the start channel and the next six channels. If the control address is
set to 100, the fixture uses channels 100, 101, 102, 103, 104, 105, and 106.
Channel 107 would be the control address for the next fixture.
If two or more fixtures are set up with the same address, they will receive
the same instructions and should behave identically. Setting up identical

Settings 15
fixtures with the same address is a good tool for troubleshooting
unexpected behavior and an easy way to achieve synchronized action.
Important! When setting the address, either use single-fixture mode or
isolate all other fixtures from the uploader.
To set the control address:
1 Prepare an upload device as described in the uploader user manual. If you
know the address to which the fixture is currently set, that is, the address to
change from, connect the uploader to the data link and use single-fixture
mode. Otherwise, use all -fixtures mode and isolate all other fixtures from
the uploader. Apply power to the fixture.
2 If using single-fixture mode, scroll to the fixture’s current (from) address and
press OK.
3 Select DMX address from the fixture menu.
4 Scroll to the desired control address and press OK.
5 Press OK again to confirm and save the setting.
PERSONALITY SETTINGS
The following settings are available to modify fixture behavior.
DMX Lamp-off: When the DMX Lamp-off personality is on (the default
setting), lamp power can be turned off from the controller by setting channel
1 to a decimal value from 248 to 255. When set to off, the lamp-off
command executes only if channels 3, 4, and 5 are set to values from 230 to
232.
DMX reset: When the DMX Reset personality is on (the default setting), the
fixture can be reset from the controller by setting channel 1 to a decimal
value from 208 to 217. When set to off, the reset command executes only if
channels 3, 4, and 5 are set to values from 230 to 232.
Automatic Lamp-on: When the Automatic Lamp-on personality is on, the
fixture turns on the lamp within 90 seconds of power on. When set to off (the
default setting), a lamp-on command is required to turn on the lamp.
To set a personality setting:
1 Prepare and connect an upload device as described in the uploader user
manual. Apply power to the fixture.
2 Select single fixture mode to change a setting on a single fixture, or all-
fixtures mode to make global changes.

16 Settings
3 If using single-fixture mode, enter the fixture’s address.
4 Select Special from the fixture menu.
5 Select the desired personality and setting. (See “MP-2 control menu” on
page 39.) Press OK.
CLOCK
The Exterior 200 has a battery operated 24-hour clock that can start and
stop stand-alone operation.
To set the clock:
1 Prepare and connect an upload device as described in the MP2 Uploader
manual. Apply power to the fixture.
2 Select all-fixtures mode.
3 Select Time from the fixture menu.
4 Select Hour and scroll to the current hour.
5 Press OK.
6 Select Minute and scroll to the current minute.
7 Press OK.
8 Press Back to return to the main menu.

General operation 17
G ENERAL OPERATION 4
GENERAL GUIDELINES
For optimum lamp life, turn off lamp power whenever illumination is not
required for extended periods of an hour or more. Fixture power may remain
on when not in use.
When the temperature is expected to fall below freezing, leave the fixture
powered on when not in use to keep the electronics warm. The lamp,
however, may be switched off.
Always allow the lamp to warm up fully before turning it off.
Avoid turning on several lamps at once.
THE LEDS AND FIXTURE OPERATING
STATUS
Two LEDs on the rear panel display the
fixture status. Normal operation is indicated
by two green LEDs. See Ta bl e 4 for other
status messages.
The LEDs flash off for a brief instant at
regular intervals to prevent false readings
when the light sensor samples the light level.
Appearance Message, LED 1 Message, LED 2
Steady green Effects OK Data OK.
Steady red -Invalid data/no data
Steady yellow Upload in progress Upload in progress
Blink red Memory error -
Blink yellow Reset in progress Reset in progress
Off -No data detected
Table 4: LED status messages
LED 1 LED 2 SENSOR

18 General operation
The installed firmware version number is displayed by the LEDs on power
up. The number of red flashes in LED 1 indicates the digit to the left of the
decimal point and the number of green flashes in LED 2 indicates the digit to
the right of the decimal point. For example, if the firmware version is 1.3,
LED 1 flashes red once and LED 2 flashes green three times.

Stand-alone operation 19
S TAND - ALONE OPERATION 5
This chapter describes how to operate the Exterior 200 in stand-alone mode
where the fixture executes color changes at set intervals and speeds, at
pre-defined periods during the day, or when the light level falls below a
defined level. The term stand-alone is used to mean that the Exterior 200 is
not connected to a controller, but is programmed with a series of up to 20
scenes that play continuously in a loop. The term ‘stand-alone operation’
can be applied to a single fixture, or to multiple fixtures operating
synchronously.
Up to 32 Exterior 200s may be connected for synchronized operation
triggered by a “master” fixture. Synchronous operation of multiple Exterior
200s requires that they be connected on a data link.
Execution of a stand-alone program may be set to start automatically upon
power-on, or toggled on/off with an MC-X controller, which also provides
direct selection of seven scenes.
When programming for stand-alone operation, you might find the summary
of commands available in “MP-2 control menu” on page 39 useful as a quick
reference.
PROGRAMMING FIXTURES
The programming of scenes, and setting up of master/slave relationships, is
performed using an MP-2 Uploader. The uploader is connected to the
fixture, used to program the stand-alone settings for that fixture (or all the
fixtures connected to that fixture by data link), and then removed. Once a
fixture is subsequently switched on it can automatically run the scenes in its
program in a loop, according to the triggering criteria you have specified
(time of day, or light level).
To summarize, you can use the MP-2 Uploader to program:
• Individual fixtures, one at a time.
• The same program in multiple fixtures that are linked with data cables.
• Individual programs in multiple fixtures that are linked with data cables.

20 Stand-alone operation
If you are not familiar with the use of the MP-2, then it is recommend that
you familiarize yourself with it using the MP-2 Uploader manual.
Getting started
1 Plug the fixture’s, or data link’s, data-input cable (male) into the 3-pin
“DMX/RS-485 OUT” socket on the MP-2.
2 Apply power to the fixture and the MP-2.
3 Select Read Memory Card from the MP-2 menu.
4 Select EXT200 ver. x.x. (Note that x.x is the number that
corresponds to the firmware level that is loaded in the fixture. The installed
firmware version number is displayed by the LEDs on power up. The
number of red flashes in LED 1 indicates the digit to the left of the decimal
point and the number of green flashes in LED 2 indicates the digit to the
right of the decimal point. For example, if the firmware version is 1.3, LED 1
flashes red once and LED 2 flashes green three times.)
5 Select Fixture menu. It is from this point you use the keys on the
uploader to navigate and select the desired menu item. For further guidance
see the following sections.
Selecting fixtures to program
Before selecting any fixture to program you must have set its control
address. If you have not yet done so, follow the instructions described in
“Control address” on page 14.
You have the option of programing all the Exterior 200s on a data link, or an
individual Exterior 200. Fixture-specific settings such as the control address
should be made in single-fixture mode. If no other fixtures are connected,
however, then all-fixtures mode may be used. Global settings are made
easiest in all-fixtures mode. For example, it might be appropriate to program
the time, or trigger criteria into all fixtures simultaneously, while program
scenes might be programmed into fixtures individually.
Note that it is important that all the fixtures have the same software level set,
or the results will be unpredictable. For more information see, “Firmware
updates” on page 35.
Selecting a single fixture
To program a single fixture:
1 Select Single address from the Fixture menu.