Martin JEM ZR44 Hi-MASS User manual

user manual
ZR44 HI-MASS
P/N 35010032-C
TM

2 Dimensions
Dimensions
All dimensions are in millimeters
©2010 Martin Professional A/S. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct
or indirect loss, consequential or economic loss or any other loss occasioned by the use of,
inability to use or reliance on the information contained in this manual. The Martin logo, the
Martin name and all other trademarks in this document pertaining to services or products by
Martin Professional A/S or its affiliates and subsidiaries are trademarks owned or licensed by
Martin Professional A/S or its affiliates or subsidiaries.

Contents
3
Contents
Dimensions................................................................................................................................ 2
Contents .................................................................................................................................... 3
Safety information...................................................................................................................... 4
Product overview ....................................................................................................................... 7
Product description................................................................................................................ 7
Features at a glance .............................................................................................................. 7
Product details ....................................................................................................................... 8
Quick Start................................................................................................................................. 9
Setting up............................................................................................................................... 9
Making fog ............................................................................................................................. 9
Installation and setting up ....................................................................................................... 10
Location ............................................................................................................................... 10
AC power ............................................................................................................................. 10
Setting up............................................................................................................................. 11
Final checks ......................................................................................................................... 11
Turning on the power........................................................................................................... 11
Control settings ....................................................................................................................... 12
Overview .............................................................................................................................. 12
Manual firing ........................................................................................................................ 12
Setting fog output level........................................................................................................ 12
Setting the Timer.................................................................................................................. 12
Setting the master-slave link mode ..................................................................................... 12
Digital remote control .............................................................................................................. 13
Overview .............................................................................................................................. 13
Functions ............................................................................................................................. 13
DMX control ............................................................................................................................. 14
Overview .............................................................................................................................. 14
Connection........................................................................................................................... 14
DMX functions...................................................................................................................... 14
Setting the DMX address ..................................................................................................... 15
Fog fluid types ......................................................................................................................... 16
Basic service............................................................................................................................ 17
Cleaning............................................................................................................................... 17
Fuse replacement ................................................................................................................ 17
Troubleshooting ...................................................................................................................... 18
Resetting the machine after fluid out ................................................................................... 18
Specifications .......................................................................................................................... 19
Notes ....................................................................................................................................... 22

4 Safety information
Safety information
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the system only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service.
Preventing electric shocks
•Always ground (earth) the machine electrically.
•Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
•Before connecting the smoke machine to power, check that the voltage
indicated on the machine’s serial label matches your local AC power
voltage. If your AC power voltage does not match, do not use the
machine. Contact Martin Service for assistance.
•Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
•If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine
and contact Martin Service for assistance. If the supply cord is
damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
•Disconnect the machine from AC power before servicing and when not
in use.
•This system is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.
•Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.

Safety information
5
•Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Martin.
•Do not operate the machine if any parts are damaged, defective or
missing.
•Moisture and electricity do not mix. Do not aim smoke output at
electrical connections or devices.
Preventing burns and fire
•The smoke produced by the machine is hot enough to cause burns
when it leaves the nozzle, and very hot droplets of fluid escape
occasionally. Keep people and objects at least 1 meter (39 inches) away
from the smoke output nozzle.
•Do not touch the smoke output nozzle during or after use – it becomes
extremely hot and remains hot for several hours after the machine has
been shut down.
•Smoke output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point smoke output at sources of
ignition such as open flames or pyrotechnic effects.
•Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•Replace fuses only with ones of the type and rating specified in this
manual for the machine.
•Provide a minimum free space of 100mm (4 inches) around the
machine.
•Provide a minimum free space of 500mm (20 inches) around fans and
air vents and ensure free and unobstructed air flow to and around the
machine.
•Keep the machine at least 600mm (24 inches) away from combustible
and heat-sensitive materials.
•Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
•Do not operate the machine if the relative air humidity exceeds 80%.
Preventing injuries
•Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
•Do not install the machine over areas where people are present.
•This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
•Smoke machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.
•Ensure at least 2m visibility in areas where smoke is being produced.
•Smoke fluid contains food-grade glycols in solution but may present
health risks if swallowed. Do not drink it. Store it securely. If eye contact
occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.

6 Safety information
Preventing breathing problems
•A smoke machine can operate safely only with the smoke fluid it is
designed for. Use the machine only with fluids specified under “Smoke
fluid options” on page 13 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the
machine.
•Do not create dense smoke in confined or poorly ventilated areas.
•Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to smoke output.
•Do not point smoke output directly at a person’s face or at face height.

Product overview
7
Product overview
Product description
The Jem ZR44 Hi-Mass™ is a reliable and highly efficient fogger capable of
precise fog delivery from subtle to massive. Ideal for a variety of settings from
small venues to huge stadiums and arenas, it features advanced technology for
top-quality performance, as well as advances in digital functionality such as
RDM compatibility.
Following on from its predecessor the industry standard ZR33 the new
Jem ZR44 Hi-Mass™ encompasses what Martin smoke machines are all about:
state of the art technology, high quality and ruggedness.
Congratulations on your purchase of this smoke machine from Martin. Details of
the full range of Martin products are available on our website at
www.martin.com.
Features at a glance
•Tough and solid design
•On board remote control
•1200 m³/min fog output
•Digital link machine to machine (Using optional Digital Multi-Function
remote)
•Continuous operation (at reduced output)
•Indirect fluid sensing
•3 & 5 pin DMX interface
•RDM capable
•Soft Start technology
•Timer / output level remote
•Fast heating/reheat times
•Proprietary Pro Steam Simulation fluid solution
•Different fluid options for different applications
•Leaves no oil residue on light fixtures
•9.5L fluid capacity
•Flying bracket as standard
•Neutrik PowerCon connector
•DTP direct thermal fault protection device

8 Product overview
Product details
Remote control
Warning, high
temperature vapour and
surfaces!
Power inlet
connector
Main power
switch
Dip switch
(DMX address)
A
VR program
upload socket
5 pin DMX
input and
link
3 pin DMX
input and
link
Fluid tank
Fog output
nozzle
Flying
bracket
Remove remote control to access
Digital remote (accessory) socket.

Quick Start
9
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot
of fog. This section tells you how to do that. However, please also make the time
to read the safety and servicing instructions in the remainder of this manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the smoke
output.
Fill the fluid tank with MARTIN-approved fluid (see page 16).
Connect a suitably rated power supply to the machine. The power requirements
are:
8.21A at 230V (EU)
14.58A at 120V (US)
Now set the mains switch, at the rear of the machine, to the ‘ON’ position and
press the grey “stand-by” button.
The ‘Ready’ LED will flash indicating the machine is heating up; allow around
10 minutes for the machine to reach operating temperature. Once the machine
has heated the ‘Ready’ LED will stop flashing and be permanently on.
Making fog
Once the machine has heated up, hold the FOG button on the remote to start
the fog output.
It may be necessary to prime the machine, to do this simply hold down the FOG
button and turn the output knob to maximum. Keep the button held until the fog
output is strong and steady. Then turn the knob back to the required output
level and release the FOG button.
You can set the fog density by turning the knob. If the knob is turned fully
anticlockwise, no fog will be produced.

10 Installation and setting up
Installation and setting up
DANGER! DO NOT operate the smoke machine until you have read and
observed all the precautions listed under “Safety information” on page 4.
Location
The smoke machine may be located on the floor or may be suspended using
the flying bracket. If suspending the machine, a standard truss bracket
(available from Martin) should be attached to the machines flying bracket with
an M12 bolt and nyloc nut.
The machine can operate in any orientation from 45 degrees upwards to 45
degrees downwards. Steeper tilting may cause fluid leakage.
If the machine is to be suspended, ensure the mounting surface can support the
weight of the machine. Do not suspend the machine over areas where people
will be underneath.
Ensure that there is at least 100mm clearance all round the machine and at least
600mm in front of the smoke output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• For EU (230V) use fit a plug rated 10 amp minimum
• For US (120V) use fit a plug rated 16 amp minimum
When installing the plug, follow the plug manufacturer’s instructions and
connect pins as follows:
Yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire function marking screw colour
brown live “L” yellow or brass
blue neutral “N” silver
green/yellow earth green
Before connecting the smoke machine to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires:
8.21A at 230V (EU)
14.58A at 120V (US)

Installation and setting up
11
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service for assistance.
Setting up
Fill the fluid tank with MARTIN-approved fluid (see page 16).
If DMX control is being used, connect the machine to the DMX line (see page
15).
Final checks
Before applying power to the smoke machine, verify the following:
•the machine is safely located or installed and meets the location
requirements stated on page 10
•the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 4
•the smoke fluid is one of the genuine Martin fluids listed under “Smoke
fluid options” on page 16
•the machine is electrically grounded (earthed)
•the AC power distribution circuits and lines are adequately rated for the
current load
Turning on the power
Turn on the main power switch located next to the power cable inlet.
The green ‘Ready’ indicator on the rear of the machine will flash for about 10
minutes as the machine heats up to operating temperature.
When the green Ready indicator stops flashing and is permanently on, the
machine is ready to make fog.

12 Control settings
Control settings
Overview
The unit is controlled using the remote control. You can control it in these ways:
•Manual firing by holding down the FOG button
•Automatic fog bursts using a repeating timer
Manual firing
Hold down the FOG button. The machine will produce fog until you release the
button.
If a long burst of fog is produced, after a time the fog output level will be
automatically reduced to keep the machine temperature within the operating
range. This allows continuous operation, so that the machine does not have to
stop and re-heat.
Setting fog output level
Set the knob to the desired output level while firing the machine. The fog output
level is always set by the current position of the knob, whether manually firing or
in timer mode.
Setting the Timer
FOG BUTTON: Will when the machine has reached operating temperature fire
the machine when pressed and held.
STAND-BY BUTTON: This turns the machines electronics on and off.
TIMER VALUE BUTTON: When the timer is being used, the timer values can be
adjusted by a factor of 8, i.e. a 5 second minimum run time becomes 40
seconds & a 10 second delay time becomes 1 minute 20 seconds.
TIMER ENGAGE: This will engage the timer to fire the machine according to the
present settings.
OUTPUT CONTROL: Turning this knob clockwise will increase the output of the
machine, if turned fully anti-clockwise there will be no output.
DELAY TIME CONTROL: This will adjust the amount of time the machine waits
between operating when the timer is engaged.
RUN TIME CONTROL: This will adjust the time the machine will operate for
when the timer is engaged.
POWER LED: This LED will light when the machine is switched on
CYCLE LED: This LED will light when the timer is engaged and the machine is
operating.
Setting the master-slave link mode
It is possible to control several machines from either the onboard remote control
or the optional accessory digital remote. The machines are interconnected with
DMX cabling via either the 3pin or 5 pin xlr sockets situated on the rear of the
machine
Dip switch 11 located on the rear of the machine must be set to the down
position on the master unit.

Digital remote control
13
Digital remote control
Overview
A Digital Remote control, available separately, may be used for control of the
JEM ZR44 HI-MASS™
Functions
The remote control provides the following functions:
•Fog button: turns fog output on and off. Press once to start fog and
again to stop.
•Timer button: turns the fog timer on and off.
•Fog level setting (Fog = 0 -100%)
•Timer run time/off time settings (415., 4/&& = 0 - 90 seconds)
•Run mode (RUN = /&&, 34"9, 4)-%, #/.4)
The Fog button works by setting RUN to #/.4 (or 34"9). The Timer button
sets RUN to 4)-% or 34"9. These buttons are simply a quick way to
control this menu function.
Display
Timer button
Fog button
XLR socket
XLR socket
(on rear)

14 DMX control
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512 standard may be used to control
and program the fog output of the smoke machine.
Connection
The smoke machine provides both 3 & 5pin XLR plug and socket on the rear
panel for DMX connection. The wiring is shown below.
Connector pin function
1Ground
2Data – (“Cold”)
3 Data + (“Hot”)
For best results, use cable designed for high speed digital data transmission.
Suitable DMX cable is available from your Martin dealer.
DMX functions
The smoke machine operates from a single DMX channel which gives
proportional control of fog density from 0-100%.
DMX Level function
0 – 12No fog
13 – 255Fog at variable density, (13=minimum, 255=maximum)
When the machine is receiving valid DMX data, the indicator light next to the
address switches will light.

DMX control
15
Setting the DMX address
Each unit on a DMX system must be allocated an address so that the DMX
controller can send separate commands to the unit. On the smoke machine, the
DMX address is set using the bank of switches (“dip switches”) on the back
panel next to the DMX connectors. The switch settings for each possible DMX
address are given in the table below.
DIP-Switch Setting
0 = OFF
1 = ON
#9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
#8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
#7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
#6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
#1#2#3#4#5
0 0 0 0 0 32
64 96
128
160
192
224
256
288
320 352
384 416
448 480
1 0 0 0 0 1 33
65 97
129
161
193
225
257
289
321 353
385 417
449 481
0 1 0 0 0 2 34
66 98
130
162
194
226
258
290
322 354
386 418
450 482
1 1 0 0 0 3 35
67 99
131
163
195
227
259
291
323 355
387 419
451 483
0 0 1 0 0 4 36
68 100
132
164
196
228
260
292
324 356
388 420
452 484
1 0 1 0 0 5 37
69 101
133
165
197
229
261
293
325 357
389 421
453 485
0 1 1 0 0 6 38
70 102
134
166
198
230
262
294
326 358
390 422
454 486
1 1 1 0 0 7 39
71 103
135
167
199
231
263
295
327 359
391 423
455 487
0 0 0 1 0 8 40
72 104
136
168
200
232
264
296
328 360
392 424
456 488
1 0 0 1 0 9 41
73 105
137
169
201
233
265
297
329 361
393 425
457 489
0 1 0 1 0 10 42
74 106
138
170
202
234
266
298
330 362
394 426
458 490
1 1 0 1 0 11 43
75 107
139
171
203
235
267
299
331 363
395 427
459 491
0 0 1 1 0 12 44
76 108
140
172
204
236
268
300
332 364
396 428
460 492
1 0 1 1 0 13 45
77 109
141
173
205
237
269
301
333 365
397 429
461 493
0 1 1 1 0 14 46
78 110
142
174
206
238
270
302
334 366
398 430
462 494
1 1 1 1 0 15 47
79 111
143
175
207
239
271
303
335 367
399 431
463 495
0 0 0 0 1 16 48
80 112
144
176
208
240
272
304
336 368
400 432
464 496
1 0 0 0 1 17 49
81 113
145
177
209
241
273
305
337 369
401 433
465 497
0 1 0 0 1 18 50
82 114
146
178
210
242
274
306
338 370
402 434
466 498
1 1 0 0 1 19 51
83 115
147
179
211
243
275
307
339 371
403 435
467 499
0 0 1 0 1 20 52
84 116
148
180
212
244
276
308
340 372
404 436
468 500
1 0 1 0 1 21 53
85 117
149
181
213
245
277
309
341 373
405 437
469 501
0 1 1 0 1 22 54
86 118
150
182
214
246
278
310
342 374
406 438
470 502
1 1 1 0 1 23 55
87 119
151
183
215
247
279
311
343 375
407 439
471 503
0 0 0 1 1 24 56
88 120
152
184
216
248
280
312
344 376
408 440
472 504
1 0 0 1 1 25 57
89 121
153
185
217
249
281
313
345 377
409 441
473 505
0 1 0 1 1 26 58
90 122
154
186
218
250
282
314
346 378
410 442
474 506
1 1 0 1 1 27 59
91 123
155
187
219
251
283
315
347 379
411 443
475 507
0 0 1 1 1 28 60
92 124
156
188
220
252
284
316
348 380
412 444
476 508
1 0 1 1 1 29 61
93 125
157
189
221
253
285
317
349 381
413 445
477 509
0 1 1 1 1 30 62
94 126
158
190
222
254
286
318
350 382
414 446
478 510
1 1 1 1 1 31 63
95 127
159
191
223
255
287
319
351 383
415 447
479 511

16 Fog fluid types
Fog fluid types
The following types of Martin/Jem fog fluid are suitable for use in this machine.
Each produces a different effect as described below. Martin supplies high
quality fog fluids that are based on ultra-pure deionized water. Use only the
following genuine Martin/Jem fog fluids. No other fluid is suitable for use.
DANGER! The smoke machine can run safely only on the specific smoke fluids it
is designed for. Use ONLY the Martin/Jem smoke fluids designated in this
manual. NEVER use any other type of fluid, or toxic gas may be produced. You
will probably also cause damage to the system that is not covered by the product
warranty. Do not dilute smoke fluid with water or any other liquid. Discard smoke
fluid if it becomes contaminated.
Regular DJ Fluid (DJ mix)
Regular DJ fluid is an economical fluid that gives a good, medium density
smoke well-suited for atmospheric effects.
Pro Smoke Super (ZR mix)
Pro Smoke Super fluid is a high-quality, general purpose fluid that produces a
dense white airborne fog with medium dispersal time. Its medium to high index
of refraction permits both good atmospheric effects and denser “white-outs”.
Pro Smoke High Density (SP mix)
Pro Smoke High Density fluid generates a high density, white, airborne fog with
a very high index of refraction and slow evaporation rate. It is well suited for
scenic obscuring, dramatic strobe effects, and “white-outs”.
Pro Smoke Studio (DX mix)
In a studio or theater environment, a lighter, faster dispersing fog is often
preferred. Pro-Smoke Studio offers a less dense environment to Pro-Smoke
Super and is therefore less likely to interfere with TV camera focusing.
i-fog
i-fog is not only kind to your lights, but is also more economical to use thanks to
its incredible long “hang time” characteristics. In environments unaffected by
extraction and air-conditioning, i-fog can be expected to last
Pro Steam Simulation
Steam simulation fluid specifically designed for ‘steam’ effects. Creates a white
burst, but is fast dispersing.
(In order to optimise the machines temperature setting the dip switch on the
rear marked ‘Low Temp’ should be set down to position 1).

Basic service
17
Basic service
Before servicing the smoke machine, read and observe all the precautions listed
in “Safety information” on page 4. Any service not described in this section must
be carried out by a Martin service technician.
Cleaning
Excessive dust, smoke fluid, and dirt build-up will degrade performance and
cause overheating and damage to the machine that is not covered by the
product warranty. To maintain adequate cooling, dust must be cleaned from the
outer casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The smoke output nozzle remains hot for up to 10 hours after use.
•Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
•Clean smoke fluid residues from the fog output of the machine using a
damp cloth.
•Clean the outer casing with a damp cloth only.
Fuse replacement
The main fuse for the smoke machine is located on the electronics board inside
the unit.
DANGER! Disconnect the power supply before removing any covers. Live parts
inside!
To replace the fuse, disconnect the power cord from the supply, unscrew the
screws holding the rear cover of the unit and remove the cover. The electronics
board is located at the back of the unit.
Remove the spent fuse and replace with one of exactly the same size and rating.
The fuse type is indicated below. Contact Martin Service if the fuse blows
repeatedly.
120V = 20AT
230V = 10AT

18 Troubleshooting
Troubleshooting
Problem Probable cause(s) Suggested remedy
Machine will not produce fog
when remote control Fog
button pressed
Machine not at operating
temperature Wait 10 to 15 minutes
Machine not powered up or
heaters disabled
Ensure mains power switch
on, enable heaters by
pressing FOG
Output level control set to
zeroIncrease setting
Machine continues to
produce fog when Fog
button is not pressed
Timer is engaged
Disengage the timer by
pressing the FOG/TIMER
ENGAGE button briefly
Machine can be fired from
the remote control, but not
by DMX controller
DMX address setting
incorrect
Change DMX address (page
15)
Poor connection in DMX line Check DMX cables and
connections
Smoke output is weak Machine requires priming Prime machine (page 9)
Wet, greasy, non-uniform
smoke output, fluid drips or
spits from nozzles, or very
loud noise when firing
machine
Incompatible smoke fluid Use only approved fluid!
Machine appears dead
Mains fuse blown Replace fuse (page 17)
No power at AC cable inlet Check power cable and
circuit breaker
Resetting the machine after fluid out
If the machine runs out of fluid it will automatically shut down to prevent any
damage occurring, the Low Fluid led on the rear will illuminate. To reset simply
turn the mains power off and back on again. Refill the fluid container and follow
the priming instructions under ‘Making fog’ on page 8.

Specifications
19
Specifications
Physical
Length .........................................................................................................685mm
Width ...........................................................................................................345mm
Height..........................................................................................................225mm
Dry weight .......................................................................................................19Kg
Performance
Effect coverage ....................................................................................1200m3/min
Operating time ...................................................................................... continuous
Warm up time ....................................................................................... 10 minutes
Max’ operating time at full output (9.5L) ............................................. 3 hrs 10 min
Control and programming
Control options ................... onboard analogue remote control, DMX (3 & 5 pin),
Multi function digital remote control (optional), RDM capable.
Digital link machine to machine (using optional digital remote control)
DMX channels ...................................................................................................... 1
Fluid system
Capacity .......................................................................................................... 9.5 L
Fluid consumption (max) ...................................................................... 120ml/min
Fluid Sensing .....................................................Indirect for unattended operation
Connections
DMX / RDM....................................................................................... 3 or 5 pin XLR
Remote / machine link .............................................................................3 pin XLR
AC power ..................................................................................Neutrik PowerCon
Electrical
AC voltage (EU) ....................................................................... 220-240V, 50/60Hz
AC voltage (US) ....................................................................... 110-120V, 50/60Hz
Main fuse (EU) ...............................................................................................10AT
Main fuse (US) ...............................................................................................20AT
Power usage (EU) .......................................................................... 1890W (8.21A)
Power usage (US) ........................................................................ 1750W (14.58A)
Thermal
Maximum ambient temperature (Ta max)............................................ 40°C (104°F)
Exterior surface temperature, steady state, at 20°C ambient .............. 50°C (122°F)
Approvals
European EMC:......................................................................... EN 61000-6-3:2001
European safety:......................................................................... EN 60 335-1:2002
Immunity: .................................................................................. EN 61000-6-1:2001
ETL approval (pending) .................... UL Std.998, CAN/CSA Std. C22.2 No 104-01

20 Specifications
Included items:
User manual
Power cable
Onboard remote control
Container 9.5L
Ordering information
Jem ZR44 Hi-Mass™ smoke machine 120V ......................................P/N 92215310
Jem ZR44 Hi-Mass™ smoke machine 230V ......................................P/N 92215300
Accessories
Digital Multi-function Remote Control ................................................P/N 92765037
Ducting system ..................................................................................P/N 92625005
Drip tray..............................................................................................P/N 92620011
Specifications subject to change without notice. For the latest product specifications, see
www.martin.com