Martin PAR 2 RGBW Zoom User manual

PAR 2 RGBW Zoom
User Manual
Professional Entertainment Technology

© 2013-2014 Martin Professional. Information subject to change without notice. Martin
Professional and all affiliated companies disclaim liability for any injury, damage, direct or indirect
loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or
reliance on the information contained in this manual. The Martin logo, the RUSH by Martin logo,
the RUSH by Martin name, the Martin name and all other trademarks in this document pertaining
to services or products by Martin Professional or its affiliates and subsidiaries are trademarks
owned or licensed by Martin Professional or its affiliates or subsidiaries.
Martin Professional • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark • www.martin.com
Manual: Revision C

Table of contents
Safety information............................................................................................. 4
Introduction ....................................................................................................... 8
Before using the product for the first time ..................................................... 8
Physical installation .......................................................................................... 8
Fastening the fixture to a flat surface............................................................ 9
Mounting the fixture on a truss...................................................................... 9
Securing with a safety cable ......................................................................... 9
AC power ........................................................................................................ 10
Linking fixtures to power in a chain............................................................. 11
Fixture overview.............................................................................................. 12
Control data link.............................................................................................. 13
Tips for reliable data transmission .............................................................. 13
Connecting the DMX data link..................................................................... 14
Fixture setup ................................................................................................... 14
Using the control menus ............................................................................. 14
DMX function settings ................................................................................. 15
Dimming curves........................................................................................... 16
Blackout or Hold if DMX signal stops.......................................................... 16
Display panel backlight sleep mode............................................................ 17
White balance adjustment........................................................................... 17
Fixture test................................................................................................... 17
Stand-alone scene ...................................................................................... 18
Fixture information....................................................................................... 18
Reset ........................................................................................................... 19
Effects ............................................................................................................. 20
Maintenance ................................................................................................... 22
Cleaning ...................................................................................................... 22
Fuse replacement........................................................................................ 23
Service and repairs ..................................................................................... 23
DMX protocol .................................................................................................. 24
5-channel mode........................................................................................... 24
9-channel mode........................................................................................... 24
Control menus................................................................................................. 26
Troubleshooting .............................................................................................. 27
Specifications.................................................................................................. 28

4 RUSH PAR 2 RGBW Zoom User Manual
Safety information
WARNING!
Read the safety precautions in this manual before installing,
powering, operating or servicing this product.
The following symbols are used to identify important safety information on the
product and in this manual:
Warning!
Safety hazard.
Risk of severe
injury or death.
Warning!
LED light
emission. Risk of
eye injury.
Warning!
Refer to manual
before installing,
powering or
servicing.
Warning!
Hazardous
voltage. Risk of
lethal or severe
electric shock.
Warning!
Hot surfaces and
fire hazard.
Risk Group 2 LED product according to EN 62471. Do not
view the light output with optical instruments or any device
that may concentrate the beam.
This product is for professional use only. It is not for household
use. It product presents risks of severe injury or death due to fire
hazards, electric shock and falls.
Respect all locally applicable laws, codes and regulations when
installing, powering, operating or servicing the fixture.
Read this manual before installing, powering or servicing the
fixture, follow the safety precautions listed below and observe all
warnings in this manual and printed on the fixture. Keep this
manual for future use. If you have questions about how to
operate the fixture safely, please contact your RUSH by Martin™
dealer or call the Martin™ 24-hour service hotline on +45 8740
0000, or in the USA on 1-888-tech-180.
For the latest user documentation and other information about
this and all Martin™ products, please visit the Martin website at
http://www.martin.com

RUSH PAR 2 RGBW Zoom User Manual 5
Protection from electric shock
Do not expose the fixture to rain or moisture.
Shut down power to the fixture before carrying out any
installation or maintenance work and when the fixture is not in
use.
Ensure that the fixture is electrically connected to ground
(earth).
Use only a source of AC power that complies with local building
and electrical codes and has both overload and ground-fault
(earth-fault) protection.
Socket outlets or external power switches used to supply the
fixture with power must be located near the fixture and easily
accessible so that the fixture can easily be disconnected from
power.
Replace defective fuses with ones of the specified type and
rating only.
Isolate the fixture from power immediately if the power plug or
any seal, cover, cable, or other component is damaged,
defective, deformed, wet or showing signs of overheating. Do
not reapply power until repairs have been completed
Before using the fixture, check that all power distribution
equipment and cables are in perfect condition and rated for the
current requirements of all connected devices.
Use only Neutrik PowerCon cable connectors to connect to the
fixture’s power sockets.
Do not connect devices to power in a chain that will exceed the
electrical ratings of any cable or connector used in the chain.
The supplied power input cable is rated 6 A and can safely
supply only one fixture with mains power. Do not connect any
device to the fixture’s MAINS OUT connector when using this
cable. If you replace this cable and also use the replacement
cable to supply only one fixture with mains power, the
replacement cable must also be rated 6 A minimum, have three
conductors 18 AWG or 0.75 mm² minimum conductor size, have
an outer cable diameter of 6 - 15 mm (0.2 - 0.6 in.) and be
temperature-rated to suit the application. In the USA and
Canada the cable must be UL listed, type SJT or equivalent. In
the EU the cable must be type H05VV-F or equivalent.
To connect fixtures to mains power in a chain, you must first

6 RUSH PAR 2 RGBW Zoom User Manual
obtain 12 AWG or 2.5 mm
2
power input and throughput cables
that are 16 A rated and temperature-rated to suit the application.
In the USA and Canada the cables must be UL-listed, type SJT
or equivalent. In the EU the cables must be type H05VV-F or
equivalent. Suitable cables with Neutrik PowerCon connectors
are available from Martin™ (see Accessories on page 29). If you
use these cables, you can connect fixtures to power in a linked
chain, MAINS OUT throughput socket to MAINS IN input socket,
but do not link more than:
•eight (8) RUSH PAR 2 fixtures in total at 100-120 V, or
•eighteen (18) RUSH PAR 2 fixtures in total at 200-240 V.
The voltage and frequency at the MAINS OUT socket are the
same as the voltage and frequency applied to the MAINS IN
socket. Only connect devices to the MAINS OUT socket that
accept this voltage and frequency.
Protection from burns and fire
Do not operate the fixture if the ambient temperature (Ta)
exceeds 40° C (104° F).
The surface of the product casing can reach up to 85° C
(185° F) during operation. Avoid contact by persons and
materials. Allow the fixture to cool for at least 15 minutes before
handling.
Keep flammable materials well away from the fixture. Keep all
combustible materials (e.g. fabric, wood, paper) at least 200 mm
(8 in.) away from the fixture housing.
Ensure that there is free and unobstructed airflow around the
fixture. Provide a minimum clearance of 100 mm (4 in.) around
fans and air vents.
Do not illuminate surfaces within 200 mm (8 in.) of the fixture.
Do not attempt to bypass thermostatic switches or fuses.
Do not stick filters, masks or other materials onto any optical
component.
Protection from eye injury
Do not look at LEDs with magnifiers, telescopes, binoculars or
similar optical instruments that may concentrate the light output.

RUSH PAR 2 RGBW Zoom User Manual 7
Protection from injury
Fasten the fixture securely to either a fixed surface or fixed
structure when in use. The fixture is not portable when installed.
Ensure that any supporting structure and/or hardware used can
hold at least 10 times the weight of all the devices they support.
If suspending from a rigging structure, fasten the fixture to a
rigging clamp. Do not use safety cables as the primary means of
support.
If the fixture is installed in a location where it may cause injury or
damage if it falls, install as directed in this manual a secondary
attachment such as a safety cable that will hold the fixture if a
primary attachment fails. The secondary attachment must be
approved by an official body such as TÜV as a safety
attachment for the weight that it secures, must comply with EN
60598-2-17 Section 17.6.6 and must be capable of bearing a
static suspended load that is ten times the weight of the fixture
and all installed accessories.
Check that all external covers and rigging hardware are securely
fastened.
Block access below the work area and work from a stable
platform whenever installing, servicing or moving the fixture.
Do not operate the fixture with missing or damaged covers,
shields or any optical component.
In the event of an operating problem, stop using the fixture
immediately and disconnect it from power. Do not attempt to use
a fixture that is obviously damaged.
Do not modify the fixture or install other than genuine RUSH by
Martin™ parts.
Refer any service operation not described in this manual to a
qualified technician.

8 RUSH PAR 2 RGBW Zoom User Manual
Introduction
The RUSH PAR 2 RGBW Zoom™ is a bright single-lens LED PAR Can with
fully premixed color from 12 RGBW LEDs and a 10 to 60° motorized zoom. It
offers electronic dimming and strobe and comes with a flexible bracket for floor
or truss mounting.
The PAR 2 RGBW Zoom can be controlled using any DMX-compliant
controller. The fixture is supplied with a 1.5 m (5 ft) power cable (local power
plug not included) and a mounting bracket with two legs.
Before using the product for the first time
1. Read Safety information on page 4 before installing, powering, operating
or servicing the fixture.
2. Unpack and ensure that there is no transportation damage before using
the fixture. Never attempt to operate a damaged fixture.
3. If the fixture is not going to be hard-wired to an AC mains power source,
install a local power plug (not supplied) on the end of the supplied power
cable.
4. Before operating, ensure that the voltage and frequency of the local power
source match the mains power requirements of the fixture.
5. Check the Martin Professional website at www.martin.com for the most
recent user documentation and technical information about the fixture.
RUSH by Martin™ user manual revisions are identified by the revision
letter at the bottom of the inside cover.
When the fixture is powered on for the first time, it may smoke slightly as it
warms up, but this will only last a few minutes and is no cause for concern.
Physical installation
Read ‘Safety information’ on page 4 before installing the
fixture.
The fixture is designed for indoor use only and must be used in
a dry location with adequate ventilation. Ensure that none of the
fixture’s ventilation slots are blocked and ensure that the product
is fastened to a secure structure or surface.

RUSH PAR 2 RGBW Zoom User Manual 9
Fastening the fixture to a flat surface
The fixture can be fastened to a hard, fixed, flat surface that is oriented at any
angle. Ensure that the surface can support at least 10 times the weight of all
fixtures and equipment to be installed on it.
Fasten the fixture securely. Do not stand it on a surface or leave it where it can
be moved or fall over. If you install the fixture in a location where it may fall
and cause injury or damage if the primary attachment fails, secure it as
directed below with a securely anchored safety cable that will hold the fixture if
the primary fastening method fails.
Mounting the fixture on a truss
The fixture can be clamped to a truss or similar rigging
structure in any orientation. When installing the fixture
hanging vertically down, you can use an open-type clamp
such as a G-clamp. When installing in any other orientation,
you must use a half-coupler clamp (see illustration on right)
that completely encircles the truss chord.
To clamp the fixture to a truss:
1. Check that the rigging structure can support at least 10 times the weight of
all fixtures and equipment to be installed on it.
2. Block access under the work area.
3. Fold the legs of the mounting bracket together and bolt a rigging clamp
securely to the mounting bracket. The bolt used must be M12, grade 8.8
steel minimum. It must pass through both mounting bracket legs and be
fastened with a self-locking nut.
4. Working from a stable platform, hang the fixture with its clamp on the truss
and fasten the clamp securely.
5. Secure the fixture with a safety cable as directed below.
Securing with a safety cable
Secure the fixture with a safety cable (or other
secondary attachment) that is approved for the weight
of the fixture so that the safety cable will hold the
fixture if a primary attachment fails. Loop the cable
through one of the safety cable attachment points on
the fixture (see arrows in illustration on right) and
around a secure anchoring point.

10 RUSH PAR 2 RGBW Zoom User Manual
AC power
Read Safety information on page 4 before connecting the
fixture to AC mains power.
Warning! The mains power input cable supplied with the fixture
is rated 6 A and can supply only one fixture with mains power.
Do not connect any device to the fixture’s MAINS OUT power
throughput socket when using this input cable. If you want to
connect other fixtures to the MAINS OUT socket, see ‘Linking
fixtures to power in a chain’ on page 11.
For protection from electric shock, the fixture must be grounded
(earthed). The power distribution circuit must be equipped with a
fuse or circuit breaker and ground-fault (earth-fault) protection.
Socket outlets or external power switches used to supply the
fixture with power must be located near the fixture and easily
accessible so that the fixture can easily be disconnected from
power.
Do not insert or remove live Neutrik PowerCon connectors to apply or cut
power, as this may cause arcing at the terminals that will damage the
connectors.
Do not use an external dimming system to supply power to the fixture, as this
may cause damage to the fixture that is not covered by the product warranty.
Power input and throughput cables must be rated 16 A minimum, have three
conductors 1.5 mm² (16 AWG) minimum conductor size and an outer cable
diameter of 5 - 15 mm (0.2 - 0.6 in.). The cables must be hard usage type
(SJT or equivalent) and heat-resistant to 90° C (194° F) minimum. In the EU
the cables must be HAR approved or equivalent.
The fixture can be hard-wired to a building electrical installation if you want to
install it permanently, or a power plug (not supplied) that is suitable for the
local power outlets can be installed on the supplied power cable.
If you install a power plug on the power cable, follow the plug manufacturer’s
instructions and connect the wires in the power cable as shown in this table:
Earth, Ground or Neutral or NLive or L
US system Green White Black
EU system Yellow/green Blue Brown
The fixture has an auto-ranging power supply that accepts AC mains power at
100-240 V at 50/60 Hz. Do not apply AC mains power at any other voltage or

RUSH PAR 2 RGBW Zoom User Manual 11
frequency to the fixture.
Linking fixtures to power in a chain
If you obtain a 12 AWG or 2.5 mm2power input cable and 12 AWG or 2.5 mm2
throughput cables from Martin™ (see Accessories on page 29), you can relay
mains power from one fixture to another by connecting fixtures to power in a
linked daisy-chain, MAINS OUT throughput socket to MAINS IN input socket.
Using 12 AWG or 2.5mm2cables from Martin™, you can link:
•Maximum eight (8) RUSH PAR 2 RGBW Zoom fixtures in total at 100-120
V, or
•Maximum eighteen (18) RUSH PAR 2 RGBW Zoom fixtures in total at
200-240 V.

12 RUSH PAR 2 RGBW Zoom User Manual
Fixture overview
1 - Display
2 - LEDs
The two LEDs on the rear of the fixture have the following functions:
POWER On Power on
DMX On Valid DMX signal present
3 - Buttons
MENU
•Activate the menu, or
•Return to the previous level of the menu structure, or
•Press and hold to exit the menus
DOWN Go down a menu level
UP Go up a menu level
ENTER Confirm the selected function
4 – 5-pin XLR DMX input/output sockets

RUSH PAR 2 RGBW Zoom User Manual 13
5 – Primary (mains power) fuse F1
The T 6.3A fixture fuse is located in a fuse holder next to the power
input/output connectors.
6 – AC mains power IN
A blue Neutrik PowerCon socket is provided to connect the fixture to AC mains
power.
7 – AC mains power OUT (THRU)
See Safety information on page 4. The light-grey Neutrik PowerCon socket
can be used to supply power to other fixtures only if the supplied power input
cable is replaced as directed in this manual and safety limits are respected.
Control data link
A DMX 512 data link is required in order to control the fixture via DMX. The
fixture has 5-pin XLR connectors for DMX data input and output.
The number of daisy-chained fixtures is limited by the number of DMX
channels required by the fixtures in relation to the maximum 512 channels
available in one DMX universe. Note that if independent control of a fixture is
required, it must have its own DMX channels. Fixtures that are required to
behave identically can share the same DMX address and channels. To add
more fixtures or groups of fixtures when the above limit is reached, add a DMX
universe and another daisy-chained link.
Tips for reliable data transmission
Use shielded twisted-pair cable designed for RS-485 devices: standard
microphone cable cannot transmit control data reliably over long runs. 24

14 RUSH PAR 2 RGBW Zoom User Manual
AWG cable is suitable for runs up to 300 meters (1000 ft.). Heavier gauge
cable and/or an amplifier is recommended for longer runs. The pinout on all
connectors is pin 1 = shield, pin 2 = cold (-), and pin 3 = hot (+). Pins 4 and 5
in the 5-pin XLR connectors are not used in the fixture but are available for
possible additional data signals as required by the DMX512-A standard.
Standard pinout is pin 4 = data 2 cold (-) and pin 5 = data 2 hot (+).
To split the link into branches, use a splitter such as the Martin 4-Channel
Opto-Isolated RS-485 Splitter/Amplifier.
Terminate the link by installing a DMX termination plug in the output socket of
the last fixture. The termination plug, which is a male XLR plug with a 120
Ohm, 0.25 W resistor soldered between pins 2 and 3, “soaks up” the control
signal so it does not reflect and cause interference. If a splitter is used,
terminate each branch of the link.
Connecting the DMX data link
To connect the fixture to data:
1. Connect the DMX data output from the controller to the first fixture’s male
XLR DMX input connector.
2. Connect the first fixture’s DMX output to the DMX input of the next fixture
and continue connecting fixtures output to input. Terminate the last fixture
on the link with a DMX termination plug.
Fixture setup
This section explains the fixture characteristics that can be set to determine
how it can be controlled and will behave. These settings are made using the
menus available in the control panel. Settings are retained in memory when
the fixture is powered off.
A complete map of the control menu structure and brief explanations of their
purposes can be found in ‘Control menus’ on page 26.
Using the control menus
To access the control menus or to return to the next highest level in the menu
structure, press the MENU button. Navigate the menu structure using the
DOWN, UP and ENTER buttons. If you have selected a menu option, confirm
your selection and set that option using the ENTER button, or if you want to
return to the next highest level in the menu structure without making a change,
press the MENU button.
To exit the menus, press and hold the MENU button.

RUSH PAR 2 RGBW Zoom User Manual 15
DMX function settings
DMX function settings include the DMX address and DMX control mode.
DMX addressing
The DMX address, also known as the start channel, is the first channel used to
receive instructions from a DMX controller. The fixture can be controlled using
signals sent by a DMX controller over a different number of channels
depending on which DMX mode it is set to.
For example:
•In 5-channel mode, if the first fixture has a DMX address of 1, then DMX
address 6 is available for the next fixture, address 11 for the next fixture
and so on.
•In 9-channel mode, if the first fixture has a DMX address of 1, then DMX
address 10 is available for the next fixture, address 19 for the next fixture
and so on.
For independent control, each fixture must be assigned its own control
channels. Two fixtures of the same type may share the same address, if
identical behavior is desired. Address sharing can be useful for diagnostic
purposes and grouped control.
To set the fixture’s DMX address:
1. In the fixture’s control panel, use the UP and DOWN buttons to select
DMX ADDRESS and press ENTER. The fixture’s currently set DMX
address will blink in the display.
2. Use the UP and DOWN buttons to select a new address.
3. Once the new address has been selected, press ENTER to confirm it (or
to return to the higher level of the menu structure without making a change,
press MENU).
DMX channel modes
The fixture provides two control modes enabling varying degrees of DMX
control and enabling the efficient use of DMX channel bandwidth. For the
effects available and control details, see ‘DMX protocol’ on page 24. The
different modes are:
5-channel mode – Individual control of red, green, blue and white channels
for color mixing plus zoom.
9-channel mode – Full-range dimming with 16-bit fine control, shutter/strobe
effects, individual control of red, green, blue and white channels for color
mixing, ‘color wheel’ effect and zoom.
To set a fixture’s DMX channel mode:
1. Select CHANNEL MODE and press ENTER.

16 RUSH PAR 2 RGBW Zoom User Manual
2. Use the DOWN and UP buttons to select the desired DMX mode and
press ENTER to set (or, to return to the higher level of the menu structure
without making a change, press MENU).
Dimming curves
Four dimming curves are available:
DIMMER 1: LINEAR – The increase in light intensity appears to be linear
as DMX value is increased.
DIMMER 2: SQUARE LAW – light intensity control is finer at low levels
and coarser at high levels.
DIMMER 3: INVERSE SQUARE LAW – light intensity control is coarser at
low levels and finer at high levels.
DIMMER 4: S-CURVE – light intensity control is finer at low levels and
high levels and coarser at medium levels.
DIMMER 1 DIMMER 2 DIMMER 3 DIMMER 4
To set the fixture’s dimming curve:
1. Select DIMMER and press ENTER. The currently set mode will blink in the
display.
2. Use the DOWN and UP buttons to select DIMMER1, DIMMER 2, DIMMER
3, or DIMMER 4.
3. Once the mode has been selected, press ENTER to set (or, to return to
the higher level of the menu structure without making a change press
MENU).
Blackout or Hold if DMX signal stops
You can decide how the fixture should behave if you are controlling the fixture
via DMX and you stop sending the DMX signal.
1. Select BLACKOUT and press ENTER. The currently set blackout mode
will blink in the display.
2. Using the DOWN and UP buttons, select YES or HOLD to decide how the
fixture should respond if it stops receiving a DMX signal:
-If you select YES, the fixture will black out
-If you select HOLD, the fixture will continue to show the effect that it is
displaying at the time.

RUSH PAR 2 RGBW Zoom User Manual 17
3. Press ENTER to confirm your choice (or, to return to the higher level of the
menu structure without making a change press MENU).
Display panel backlight sleep mode
To set the display panel backlight to remain on all the time or to automatically
switch off when the control panel is not in use:
1. Select BACKLIGHT and press ENTER.
2. Use the DOWN and UP buttons to select ON (display backlight constantly
on) or OFF (display backlight turns off when not in use). Press ENTER to
confirm (or, to return to the higher level of the menu structure without
making a change, press MENU).
White balance adjustment
You can adjust the white balance of the fixture (to match other fixtures, for
example) by adjusting the amount of red, green or blue in the white output. To
adjust the white balance mix:
1. Select WHITE BALANCE and press ENTER.
2. Use the DOWN and UP buttons to select RED or GREEN or BLUE.
3. Press ENTER to confirm.
4. Use the DOWN and UP buttons to change the value (125-255).
5. Once the correct value has been selected, press ENTER to confirm (or, to
return to the higher level of the menu structure without making a change,
press MENU).
Fixture test
Automatic tests of all effects or manual test of individual effects can be run
from the control menus.
Automatic effects test
To perform a complete test of all of the fixture’s effects:
1. Select FIXTURE TEST and press ENTER to confirm. The automatic test
will run.
2. To stop the test and return to a higher level of the menu structure, press
MENU.
Manual effects test
The Manual effects test menu can be used to test the fixture’s effects
individually and to set a standalone scene that the fixture will show each time it
is powered on:
1. Select MANUAL TEST and press ENTER.

18 RUSH PAR 2 RGBW Zoom User Manual
2. Use the DOWN and UP buttons to select an effect: dimmer, red, green,
blue, white, color wheel, shutter or zoom. Press ENTER to confirm your
selection.
3. Use the DOWN and UP buttons to change the value (000-255). The test
will be the equivalent of sending this DMX value to the selected effect.
4. Press ENTER to confirm your selection and activate the effect (or, to
return to the higher level of the menu structure without making a change,
press MENU).
5. If you have confirmed a selection with the ENTER button, press MENU to
return to the list of effects.
6. If you want, you can now select another effect and set a value for it as
described above. This effect will be added to the effects that you have
already set.
By combining effects in this way, you can set a mix of RGBW colors plus a
strobe, for example.
Note that if you set a color wheel effect, you override any RGBW values that
have been set. If you set an RGBW color, you override any color wheel value
that has been set.
Stand-alone scene
If you power the fixture off while it is running the effect – or the combination of
effects – that you have set in the MANUAL TEST menu (see above), it will
hold that setting in memory. The next time you power the fixture on, it will
display those effects. This feature lets you set a stand-alone scene that runs
automatically each time the fixture is powered on.
Note that when the fixture is running a stand-alone scene, it will not respond to
DMX control signals.
Fixture information
Fixture temperature readout
To check the onboard temperature of the fixture:
1. Select TEMP and press ENTER. The display will show the temperature of
the unit.
2. To return to a higher level of the menu structure, press MENU.
Fixture operating time
The fixture operating time counter monitors the total number of hours the
fixture has been in operation since manufacture. To display the counter:
1. Select FIXTURE TIME and press ENTER. The display will show the time
the unit has been running.
2. To return to a higher level of the menu structure, press MENU.

RUSH PAR 2 RGBW Zoom User Manual 19
Firmware version
To see which software version is installed in the fixture:
1. Select FIXTURE VERSION and press ENTER. The firmware version will
be shown.
2. To return to a higher level of the menu structure, press MENU.
Reset
To reset the fixture to its factory default settings:
1. Select RESET and press ENTER to confirm.
2. The fixture will now reset to its default settings.

20 RUSH PAR 2 RGBW Zoom User Manual
Effects
See ‘DMX protocol’ on page 24 for a full list of the DMX channels and values
required to control the different effects.
Color control
All DMX modes offer full RGBW color mixing.
Besides color mixing, the following 32 color presets can be selected directly in
9-channel mode:
Red Green Blue White
Color 1 255 0 0 0
Color 2 255 50 0 30
Color 3 255 100 0 0
Color 4 255 150 0 0
Color 5 255 200 0 50
Color 6 255 255 0 0
Color 7 200 255 0 0
Color 8 150 255 0 10
Color 9 100 255 0 0
Color 10 50 255 0 50
Color 11 0 255 0 0
Color 12 0 255 50 10
Color 13 0 255 100 0
Color 14 0 255 150 0
Color 15 0 255 200 10
Color 16 0 255 255 0
Color 17 0 200 255 0
Color 18 0 150 255 10
Color 19 0 100 255 0
Color 20 0 50 255 50
Color 21 0 0 255 0
Color 22 50 0 255 0
Color 23 100 2 255 0
Color 24 150 0 255 50
Color 25 200 0 255 0