Maser TORRANT-V2 Operating manual

MASER TORRANT-V2
ULTRASONIC
RODENT REPELLENT
User and Installation Manual
Maser Electronics Pvt. Ltd., Mumbai.
[e-mail] www.maserindia.com 022 4111 0000 (100 Lines)

Page 2
The TorranT V2 Model supports the following protocols on RS/485
a. CRMS which is our proprietary protocol.
b. Modbus.
By default when the system is switched ON it operates on CRMS protocol.
There are two modes of operation AUTO Mode and MANUAL Mode.
By default the system runs on Auto Mode with factory preset setting (kindly refer
below table)
In this mode the Wave speed and Wave density parameters will change automatically.
In Manual Mode the above mentioned parameters will not
change automatically and the user will have to do the same
manually.
However in the Auto and Manual modes the frequency bands
will change automatically after the time for which they have
been congured.
Once the console is powered up the system will be in
operation and twenty transducers (Dedicated Connection)
connected to the console will start receiving the signal
transmission from the console.
*Parameter Name Factory Preset Value
Wave Speed ( PPM- Pulses Per Minute )
Wave Density
Band A Time (20 KHz to 50 KHz)
Band B Time (30 KHz to 60 KHz)
Band C Time (26 KHz to 57 KHz)
Band D Time (24 KHz to 61 KHz)
Band E Time (32 KHz to 62 KHz)
Password
130
80
1 Min
2 Mins
3 Mins
2 Mins
1 Mins
9999

Page 3
PANEL KEYPAD
OPERATIONS

Press m.
Enter Machine Password as mentioned above in the table by doing the following.
Use ror lto change the correct digit (9999).
Press mto access the setup.
1.
2.
3.
4.
Password Entry to Access Setup
Press m.
Enter Machine Password as mentioned above in the table
Press mthen rto choose ‘Test Setup’.
Press mto choose ‘Audible Test’ parameter.
Again press mthen ror lto check a Transducers in Audible Mode.
Use ethen rto choose ‘Fixed Frequency Test’ ie.20KHz to 62KHz.
parameter.
Press mthen ror lto choose desired frequency value.
1.
2.
3.
4.
5.
6.
7.
Transducer Testing
Page 4

Press etwo times to go back to the main Menu and after 30 seconds controller
will start displaying all the congured parameters.
8.
Press m.
1.1. Enter Machine Password as mentioned above in the “Password Entry to
Access Setup”
1.2. Press mthen rtwo times to choose the Parameter Setup.
1.3. Press mto set mode of operation.
1.4. Press mthen rto select Manual Mode.
1.5. Press ethen rto choose the parameter like Wave Speed,
Band Density & Band Timings.
1.5.a. Press mto enter the values for respective parameters.
1.5.b. Press ror lfor changing the values.
1.
Parameter Setup
Mode of Operation – Manual Mode
First change the mode of operation to Manual Mode. Steps are as follows.
Page 5

Page 6
1.5.c. Press ethen rfor changing the values of other
parameters.
Press eto go back main menu.
Go to step 1.5 if you wish to change another parameter else after 30 seconds controller
will start displaying all the congured parameters.
2.
3.
Press m.
Enter Machine Password as mentioned above in the “Password Entry to Access
Setup”.
Press rthree times to choose ‘System Setup’parameter.
Press mthen r6 times to choose ‘Factory Reset ‘parameter.
Press mtwo times for Factory Reset and after Factory Reset Controller will start
displaying all the default parameters
1.
2.
3.
4.
5.
Restore Factory Settings

Page 7
Press m.
Enter Machine Password as mentioned above in the “Password Entry to Access
Setup”.
Press rthree times to choose ‘System Setup’ parameter.
Press mthen rto choose RS-485 Mode.
Press mto choose CRMS Mode.
Press magain system will congure to CRMS Mode.
Press etwo times to go back main menu.
1.
2.
3.
4.
5.
6.
7.
CRMS Mode
Press m.
Enter Machine Password as mentioned above in the “Password Entry to Access
Setup”.
Press rthree times to choose ‘System Setup’ parameter.
1.
2.
3.
CRMS Mode Settings

Page 8
Press mthen rto choose RS-485 Mode. If your system is in MODBUS
Mode.
Press mthen lto choose CRMS Mode.
Press magain system will congure to CRMS Mode.
Press ethen lto select CRMS ID (MID).
Press mthen rto congure MID (0-255).
Press mand System will congure to CRMS with respective MID.
Press etwo times to go back to main menu.
4.
5.
6.
7.
8.
9.
10.
Press m.
Enter Machine Password as mentioned above in the “Password Entry to Access
Setup”.
Press rthree times to choose ‘System Setup’ parameter.
Press mthen rto choose RS-485 Mode.
1.
2.
3.
4.
Modbus Mode

Page 9
Press mthen rto choose MODBUS Mode.
Press magain system will congure to MODBUS Mode.
Press etwo times to go back to main menu.
5.
6.
7.
Press m.
Enter Machine Password as mentioned above in the “Password Entry to Access
Setup”.
Press rfour times to choose ‘MODBUS Setup’.
Press mSet Baud Rate.
4.1. Press mthen ror lto choose baud rate ie.1200bps to
115200bps
4.2. Press eto go back to the ‘MODBUS Setup’.
Press rto choose ‘Parity Bits’.
1.
2.
3.
4.
5.
MODBUS Mode Settings

Page 10
6.
7.
5.1. Press mthen ror lto choose Parity Bits i.e. Even, Odd
and No Parity.
5.2. Press eto go back to the ‘MODBUS Setup’.
Press rtwo times to choose‘Stop Bits’.
6.1. Press mthen ror lto choose Stop Bits i.e. 1 or 2.
6.2. Press eto go back to the ‘MODBUS Setup’.
Press rthree times to choose ‘MODBUS ID’.
7.1. Press mthen ror lto congure MODBUS ID.
7.2. Press eto go back to the ‘MODBUS Setup’ or press etwo
times to go back to the Main Menu.