Master MFG SSBK-240 User manual

HAVING TROUBLE? CALL SUPPORT AT: 320.340.6464
SSBK-240 BOOM ASSEMBLY 240-AC
TOOLS
PARTS
For each Nozzle Body, insert a Strainer, Gasket and Deflector Fan
Nozzle as shown here.
Push Nozzle Cap onto the Nozzle Body and twist to secure it.
Repeat for remaining Nozzle.
Installs Nozzles, Strainers & Caps
1.
None
TOOLS
2.
Extend the Boom Arms and align the end holes as shown.
Insert the ¾” Bolts through the holes and secure with Flange
Nuts. Tighten with Socket Wrench.
Connects Boom Arms
PARTS
Deflector Nozzle (2)
DF3.0
Flange Nuts (8)
33-100113
1” Bolts (6)
33-100116
7’ Boom Assembly (1)
34-140052-P
TOOLS REQUIRED
NOTE:
IF YOU PURCHASED A COMPLETED BROADCAST SPRAYER,
FOLLOW THE SPOT SPRAYER MANUAL AND MOUNT KIT
ASSEMBLY INSTRUCTIONS BEFORE YOU COMPLETE BOOM
ASSEMBLY STEPS.
1/2” SOCKET WRENCH KNIFE
INCLUDED
COMPONENTS
PRAYING
IMPLE
S
MOBILE SPRAY ASSISTANT
INTEGRATE YOUR SPRAY EQUIPMENT AND ACREAGE. CALCULATE YOUR NEEDED LIQUID AND APPLICATION SPEED.
Boom Upright Bracket (2)
31-100160
FREE
Gasket (2)
G-G00002020
Ball Check Strainer (2)
NS-50BC
Deflector Nozzle Cap (2)
G-8253051
NOTE: ¾” Bolts will be
pre-installed onto Boom
Assembly.

HAVING TROUBLE? CALL SUPPORT AT: 320.340.6464
SSBK-240 BOOM ASSEMBLY 240-AC
ID Part Number Description Qty
1 31-100353 Left Boom Arm 1
2 31-100354 Right Boom Arm 1
3 31-400008 L Nozzle Body - 3/8” HB 2
4 31-400010 Boom Nozzle Clips 2
5 3B34 Swivel Nut - 3/4” FGHT 1
6 3C38 Flat Seat Hose Barb - 3/8” 1
7 3T38 Tee - 3/8" Hose Barb 1
8 CTB8-40 Black Nylon Cable Tie 4
9 DF3.0 Gray Deflector Nozzle 2
10 G-8253051 Deflector Nozzle Body Caps 2
11 G-G00002020 Gasket 2
12 NS-50BC Nozzle Strainer - 50 Mesh 2
13 SHC-F Snapper Hose Clamp - 3/8” 6
14 33-103153 Rubber Hose - 3/8” 1
15 W406V Washer - 1” OD x 3/4” ID 1
16 31-100160 Boom Upright Brackets 2
17 33-100116 Bolts - 1” 6
18 33-100113 Flange Nuts 8
19 33-200120 Bolts - 3/4” 2
B. SSBK-240 BOOM BREAKDOWN
TOOLS
PARTS
Locate Boom Hose and make sure there is a Washer in the end of
Boom Cap.
Thread the Boom Hose to the Shut-Off Valve.
Connects Boom Assembly to Shut-Off Valve
4.
NOTE: Use a Knife to cut zip
tie from Boom Assembly to
free the Boom Hose.
TOOLS
3.
Secure Boom Assembly to Boom Upright Brackets with 1”
Bolts and Flange Nuts. Tighten with Socket Wrench.
Use remaining 1” Bolts and Flange Nuts to install Boom
Assembly with Boom Upright Brackets to Mount Kit.
Attaches Boom Uprights to Boom Assembly
NOTE: Boom Upright
Brackets may not be needed.
Consult Mount Kit Assembly
instructions.
PARTS
PROBLEM CAUSE SOLUTION
Boom Doesn't Spray Bad Electrical Connection Check Battery Connections
Boom Shut-Off Valve Flip On Shut-Off Valve
Irregular Spray Pattern Clogged Strainer Unclog Strainer
Pinched Or Clogged Hose Unpinch or Unclog Hose
Clogged Nozzles Unclog Nozzles
Damaged Spray Nozzles Replace Nozzles
No Nozzles In Boom Install Nozzles Into Boom
Incorrect Nozzle Size Replace with Correct Nozzles
Nozzle Facing Wrong Direction Adjust Nozzle To Correct Designation
Boom Leaks Loose Fasteners Tighten Fasteners
Loose Connection To Shut-Off Valve Tighten Boom To Shut-Off Valve
Damaged Boom Hose Replace Hose or Boom Kit
Nozzles Drip After Use No Ball Check Strainers Install Ball Check Strainers
SSBK-240 BOOM TROUBLESHOOTING
T.