Masterbuilt MB20101719 User manual
Welcome to the family. Let’s get started.
Master it. Masterbuilt.
Manual Code: 9810180001 190226-GSB
SMOKER LEG KIT
Manual applies to the following model number(s)
MB20101719
• To avoid personal injury and/or property damage, please read and follow all of these instructions
before assembly and operation.
• Use legs on stable and level surface only.
• Keep this manual for future reference.
WARNING
•BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.
• Assemble on a clean flat surface.
• Tools needed: Adjustable wrench, pliers, Phillips head screwdriver
• Approximate assembly time: 45 minutes
• Actual product may differ from picture shown.
2
NO QTY DESCRIPTION
1 1 14” Left Rear Leg
2 1 14” Right Rear Leg
3 1 14” Left Front Leg
4 1 14” Right Front Leg
5 2 Rear Brace*
6 2 Front Brace*
Parts List
NO QTY DESCRIPTION
7 1 Left Side Brace
8 1 Right Side Brace
9 2 Axle*
10 2Large Wheel with Cap
11 23” Locking Swivel Caster
1
2
4
5
6
7
8
11
3
10
9
10
11
*This leg kit is designed to fit the MES 300 and MES 400 Series by Masterbuilt.Additional parts are included
but only certain parts are needed based on the size of your smoker.
Hardware List
Ø6 Washer
Qty-10
C
M6 Flange Nut
Qty-16
B
Ø10 Washer
Qty-4
D
M10x20 Screw
Qty-2
E
M6x16 Screw
Qty-26
A
Axle Nut
Qty-2
F
3
B
B
A
A
A
A
B
B
X4
A
B
X4
Assembly
1
2
Remove grease tray. Grease tray
brackets can remain attached to
bottom of smoker, but are not
pictured in the leg kit assembly
steps.
Grease Tray Bracket
Grease Tray
Remove front brace.
4
BB
AA
AA
BB
X8
A
B
X8
B
BA
AA
AB
B
X4
A
B
X4
3
Assembly
4
Remove rear brace.
Remove left and right
side braces.
5
ED
Remove and re-use
screw and washer
R/R
R/R
D
X2
X2
E
A
A
C
C
A
A
C
C
X4
A
C
X4
Assembly
5
6
Remove rear leg screws and
washer from back of smoker.
Remove rear legs from smoker. The smaller screws and washers will be
re-used to assemble new legs.
6
Assembly
7
8
3
4
AC
AC
AC
X6
A
C
X6
X6
A
AA
A
CC
C
C
X6
Remove front legs from smoker.
Install left and right front legs with casters.
11
11
7
A
C
CA
C
CAA
1
2
X4
A
C
X4
9
10
Assembly
1
2
ED
Remove and re-use
screw and washer
R/R
R/R
D
X2
X2
E
Install left and right rear legs.Re-use smaller screws
and washers removed in step 6.
Secure left and right rear
legs to back of smoker.
1
8
9
11
12
Assembly
10
10
F
D
D
F
F
X2
Install axle through holes in rear legs, then large
wheels with caps.
A
B
A
B
BB
AA
7
8
Install left and right side braces.
X8
A
B
X8
D
X2
9
13
14
Assembly
Install rear brace.
Install front brace.
A
B
5
A
B
B
B
A
A
BA
BA
A
A
B
B
X4
A
B
X4
X4
A
B
X4
6
10
15
Assembly
Install grease tray through front
brace into grease tray brackets.
• Smoker should only be rolled on a smooth surface. Smoker should never be rolled up or down stairs or
uneven surfaces.Potential damage to smoker or harm to user may result from failure to follow warnings.
WARNING
DO NOT RETURN TO RETAILER for assembly assistance, missing or damaged parts. Please
contact MASTERBUILT customer service at 1-800-489-1581 or support.masterbuilt.com.
STOP
11
Visit masterbuilt.com or complete form below and return to:
Attn: Warranty Registration
Masterbuilt Manufacturing, LLC
1 Masterbuilt Court | Columbus, GA 31907
Name: ___________________________ Address: __________________________________________
City: ______________________________________________________________________________
State/Province: ________ Postal Code: ________________ Phone Number: _______________________
E-mail Address: ______________________________________________________________________
*Model Number: ______________________________ *Serial Number: ___________________________
Purchase Date: _____- ______-_______ Place of Purchase: ____________________________________
*Model Number and Serial Number are located on silver label on back of smoker.
Masterbuilt 1-Year Limited Warranty
Masterbuilt warrants its products to be free from defects in material and workmanship under
proper assembly, normal use and recommended care for 1 year from the date of original retail
purchase.The Masterbuilt warranty does not cover paint finish as it may burn off during normal
use.The Masterbuilt warranty does not cover rust. Masterbuilt requires proof of purchase for
warranty claim,such as a receipt. Upon the expiration of such warranty, all such liability shall
terminate.
Within the stated warranty period, Masterbuilt, at its discretion, shall replace defective
components free of charge, with the owner being responsible for shipping. Should Masterbuilt
require return of component(s) in question for inspection, Masterbuilt will be responsible for
shipping charges to return requested item. This warranty excludes property damage sustained
due to misuse, abuse, accident, or damage arising out of transportation.
This express warranty is the sole warranty given by Masterbuilt and is in lieu of all other
warranties, expressed or implied including implied warranty, merchantability, or fitness for a
particular purpose. Neither Masterbuilt nor the retail establishment selling this product has
authority to make any warranties or to promise any remedies in addition to or inconsistent with
those stated above.Masterbuilt’s maximum liability, in any event, shall not exceed the purchase
price of the product paid by the original consumer/ purchaser. Some states do not allow the
exclusion or limitation of incidental or consequential damages. In such a case,the above
limitations or exclusions may not be applicable.
California residents only: Not withstanding this limitation of warranty, the following specific
restrictions apply; if service,repair, or replacement of the product is not commercially practical,
the retailer selling the product or Masterbuilt will refund the purchase price paid for the product,
less the amount directly attributable to use by the original buyer prior to the discovery of the
nonconformity. Owner may take the product to the retail establishment selling this product in
order to obtain performance under warranty. This express warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
Rest assured, we’re here to help.
Customer Service masterbuilt.com/contact
Masterbuilt Manufacturing, LLC
1 Masterbuilt Court | Columbus, GA | 31907
@masterbuilt 1.800.489.1581
masterbuilt.com
Bienvenue à la famille. Commençons!
Maîtrisez-le. Masterbuilt.
TROUSSE DE PIEDS POUR LE FUMOIR
Le manuel s’applique au(x) numéro(s) de modèle(s) suivant(s)
MB20101719
• Pour éviter les blessures et les dommages matériels, assurez-vous de lire et de suivre toutes ces
consignes avant l’assemblage et l’utilisation.
• N’utiliser les pieds que sur une surface stable et de niveau.
• Conservez ce manuel pour référence ultérieure.
AVERTISSEMENT
•AVANT L’ASSEMBLAGE, LIRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS.
• Assembler l’appareil sur une surface plane et propre.
• Outils nécessaires: clé ajustable, pinces, tournevis cruciforme
• Temps nécessaire pour l’assemblage: environ 45minutes
• Le produit réel peut différer de l’illustration.
14
NO QTÉ DESCRIPTION
1 1 Pied arrière gauche de 14po
2 1 Pied arrière droit de 14po
3 1 Pied avant gauche de 14po
4 1 Pied avant droit de 14po
5 2 Support arrière*
6 2 Support avant*
Liste des pièces
NO QTÉ DESCRIPTION
7 1 Support latéral gauche
8 1 Support latéral droit
9 2 Essieu*
10 2 Grosse roue avec capuchon
11 2 Roulette orientable à blocage de 3po
1
2
4
5
6
7
8
11
3
10
9
10
11
Liste de quincaillerie
Rondelle
Ø6
Qté-10
C
Écrou
d’accouplement M6
Qté-16
B
Rondelle
Ø10
Qté-4
D
Vis M10×20
Qté-2
E
Vis M6×16
Qté-26
A
Écrou
d’essieu
Qté-2
F
*Ce kit de jambe est conçu pour s’adapter à la série MES 300 et MES 400 de Masterbuilt.Des pièces
supplémentaires sont incluses mais seules certaines pièces sont nécessaires en fonction de la taille de
votre fumeur.
15
B
B
A
A
A
A
B
B
X4
A
B
X4
Assemblage
1
2
Enlevez le bac à graisse.Les
supports du bac à graisse peuvent
rester fixés au fond du fumoir, mais ils
ne sont pas illustrés dans les étapes
d’assemblage de la trousse de pieds.
Support du bac à graisse
Bac à graisse
Enlevez le support avant.
16
BB
AA
AA
BB
X8
A
B
X8
B
BA
AA
AB
B
X4
A
B
X4
3
Assemblage
4
Enlevez le support arrière.
Enlevez le support latéral droit
et le support latéral gauche.
17
ED
Retirez la vis et la
rondelle et réutilisez-les.
R/R
R/R
D
X2
X2
E
A
A
C
C
A
A
C
C
X4
A
C
X4
Assemblage
5
6
Enlevez les vis et les rondelles du pied
arrière de l’arrière du fumoir.
Enlevez les pieds arrière du fumoir. Les vis plus petites et les rondelles
seront réutilisées pour assembler les nouveaux pieds.
18
Assemblage
7
8
3
4
AC
AC
AC
X6
A
C
X6
X6
A
AA
A
CC
C
C
X6
Enlevez les pieds avant du fumoir.
Installez les pieds avant droit et gauche avec des roulettes.
11
11
19
A
C
CA
C
CAA
1
2
X4
A
C
X4
9
10
Assemblage
1
2
ED
Retirez la vis et la
rondelle et réutilisez-les.
R/R
R/R
D
X2
X2
E
Installez les pieds arrière droit et gauche.Réutilisez les vis plus petites et les
rondelles enlevées à l’étape6.
Fixez les pieds arrière
droit et gauche à l’arrière
du fumoir.
1
20
9
11
12
Assemblage
10
10
F
D
D
F
F
X2
Installez l’essieu au travers des trous dans les pieds avant, puis les
grosses roues avec capuchons.
A
B
A
B
BB
AA
7
8
Installez le support latéral droit et le support latéral
gauche.
X8
A
B
X8
D
X2
Table of contents
Languages:
