Mastervolt 77030500 User manual

USER’S MANUAL
Multipurpose
contact output
DC Relay for MasterBus
MASTERVOLT
Snijdersbergweg 93,
1105 AN Amsterdam
The Netherlands
Tel.: [phone]
Fax.: [phone]
www.Mastervolt.com Copyright © 2008 Mastervolt, v 1.3 December 2008
ENGLISH: PAGE 1
NEDERLANDS: PAGINA 5
DEUTSCH: SEITE 9
FRANÇAIS: PAGINA 13
CASTELLANO: PÁGINA 17
ITALIANO: PÁGINA 21

2December 2008 / Multipurpose Contact Output / EN
1 GENERAL INFORMATION
1.1 Use of this manual
Copyright © 2008 Mastervolt. All rights reserved.
Reproduction, transfer, distribution or storage of part
or all of the contents in this document in any form
without the prior written permission of Mastervolt is
prohibited.This manual serves as a guideline for the
safe and effective operation of the Multipurpose
Contact Output. Keep this manual at a secure place!
1.2 Guarantee specifications
Mastervolt guarantees that this product was built
according to the legally applicable standards and
stipulations. If you fail to act in accordance with the
regulations, instructions and stipulations in this
user’s manual, damage can occur and/or the
product will not fulfil the specifications. This may
mean that the guarantee will become null and void.
IMPORTANT: Additional warranty agreements, like
“Mastervolt system warranty” may contain
restrictions which forbid resetting of historical data
The standard guarantee period is two years after
date of purchase.
1.3 Liability
Mastervolt can accept no liability for:
•consequential damage due to use of the
Multipurpose Contact Output;
•possible errors in the manuals and the results
thereof;
•Use that is inconsistent with the purpose of the
product.
CAUTION!
Never remove the identification label.
2 OPERATION
2.1 MasterBus functions
The Multipurpose Contact Output operation is entirely MasterBus based. For information about MasterBus and
the MasterBus event structure, see www.mastervolt.com. The table below shows the relay functions.
Monitoring Function Description Factory settings Range
State Relay can be switched On (activate) or
Stand by
Stand by Stand by/ Activate
Override Change the state of the relay Stand by Activate/ Stand by
Configuration Function Description Factory settings Range
Language Set the Multipurpose Contact Output
menu language
English See specifications
Device name Any name you wish with 12 characters
max
DC Relay 12 characters max
1 sec pulse Option to create a 1 second starting
pulse, needed for some generators
Off Off, On
Min. runtime Option to use a minimum run time Off Off, On
Min. runtime Set the minimum run time if selected 15 minutes 15 min-45 days
Max. runtime Option to use a maximum run time Off Off, On
Max. runtime Set the maximum run time if selected 8 hrs 15 min-45 days
2.2 CSI for ChargeMaster
The Multipurpose Contact Output can be used as CSI (Charger Status Interface) for the ChargeMaster, switching
at charger failure. CSI configuration is done at the ChargeMaster under Configuration/ Events:
Event source Event target Event command Event action
Failure DC Relay Activate Copy
On DC Relay Activate Inverted copy

EN / Multipurpose Contact Output / December 2008 3
3 EC DECLARATION OF CONFORMITY
This product is in conformity with the provision of the EC EMC directive 89/336/EEC
and amendments 92/31/EEC, 93/68/EEC. Standards applied:
Generic emission standard: EN 50081-1:1992, Generic Immunity standard: EN 50082-1:1997,
Safety directive 2006/95/EC, with the following standard:
Low voltage standard: EN 60950: 2000
4 EXAMPLES
Where to configure: Mass Charger, Multipurpose contact controls: Fan
Where to configure: DC Distribution, Multipurpose contact controls: Buzzer
Where to configure: Sunmaster XS, XL range, Multipurpose contact controls: Power supply
Where to configure: MasterShunt, Multipurpose contact controls: Generator
Source Target Command Command Data
Insulation failure Multipurpose Contact Activate Copy
Source Target Command Command Data
Battery Low Multipurpose Contact Activate Copy
Source Target Command Command Data
Temperature High Multipurpose Contact Activate Copy
Source Target Command Command Data
Fuse blown Multipurpose Contact Activate Copy

5 INSTALLATION
Insert the MasterBus cables, then connect the relay cables to the screw terminal input and outputs, figure below.
Overview and functional scheme of the Multipurpose Contact Output
6 SPECIFICATIONS
Model: Multipurpose contact output
Article number: 77030500
Delivery also includes: Screw terminal, MasterBus cable, MasterBus Terminating device, User’s manual
Function of instrument: MasterBus controlled Multipurpose Contact Output
Potential free contact: 1:C, 2: NC – 1A / 30 V DC, 3: NO
Languages available: English,Nederlands,Deutsch,Français,Castellano,Italiano,Norsk,Svenska,Suomi,Dansk
Power consumption: 144 mW
MasterBus Powering: No
Din rail mounting: Yes, Din rail 30 mm [1.2 inch]
Protection degree: IP 21
Dimensions: 66 x 78 x 32 mm [2.6 x 3.1 x 1.3 inch]; see drawing below
Weight: Approx. 80 gr [0.18 lb]
Dimensions in mm [inch]
4,5 [0.18]
69 [2.7]4.0 [0.16]
33 [1.3]
33 [1.3]
6.0 [0.24]
78 [3.1]
32 [1.3]
4.0 [0.16]
1. Input
2. Output normally closed
3. Output normally open
4. Communication LED, illuminating when the state is “activate”
MasterBus connector
Function:
Stand by: 1 is connected 2,
Activate: 1 is connected to 3,
Maximum rela
y
current: 1A.
Snijdersbergweg 93, 1105 AN Amsterdam, The Netherlands
Tel : + 31-20-3422100
Fax : + 31-20-6971006
Email : [email protected]