Matrix Orbital GLK24064-25 User manual

GLK24064-25/GLT24064
Including GLK24064-25-USB, GLK24064-25-422, GLT24064-USB, and GLT24064-422
Technical Manual
Revision 3.2
PCB Revision: 4.0 or Higher
Firmware Revision: 8.1 or Higher
Downloaded from Arrow.com.

Revision History
Revision
Date
Description
Author
3.2
January 3, 2018
Correction to Set Non-Standard Baud Rate command
Divino
3.1
January 21, 2015
Revision to Keypad note
Divino
3.0
October 19, 2015
Revision to Commands for Firmware Revision 8.6
Clark
2.9
May 21, 2014
Revision to Commands for Firmware Revision 8.5
Martino
2.8
March 12, 2014
Revision and correction to Colour in Ordering Options
Martino
2.7
September 9, 2013
Corrected Scripted Button/Key and Keypad Brightness Commands
Clark
2.6
July 10, 2013
Updated Data Packet Size Definitions
Clark
2.5
December 13, 2012
Added Firmware Revision 8.4 Commands
Clark
2.4
October 23, 2012
Added Alternate Power requirement for YG units
Clark
2.3
October 13, 2011
Major Command Additions
Clark
2.2
March 8, 2011
Updated Electrical Specifications
Clark
2.1
January 27, 2011
Filesystem Command Updates for Firmware Revision 8.1
Clark
2.0
November 3, 2010
Initial Release
Clark
Downloaded from Arrow.com.Downloaded from Arrow.com.

Contents
1 Introduction ...............................................................................................................................................1
2 Quick Connect Guide..................................................................................................................................2
2.1 Available Headers ...............................................................................................................................2
2.2 Standard Module ................................................................................................................................3
Recommended Parts............................................................................................................................. 3
Serial Connections.................................................................................................................................3
I2C Connections .....................................................................................................................................4
2.3 USB Module ........................................................................................................................................ 5
Recommended Parts............................................................................................................................. 5
USB Connections...................................................................................................................................5
2.4 RS422 Module..................................................................................................................................... 6
RS422 Connections ...............................................................................................................................6
3 Software.....................................................................................................................................................7
3.1 MOGD# ............................................................................................................................................... 7
3.2 Firmware Upgrade ..............................................................................................................................8
3.3 Application Notes................................................................................................................................ 8
4 Hardware....................................................................................................................................................9
4.1 Standard Model .................................................................................................................................. 9
Extended Communication/Power Header ............................................................................................9
Serial DB9 Connector ............................................................................................................................ 9
Power Through DB9 Jumper ...............................................................................................................10
Protocol Select Jumpers......................................................................................................................10
Hardware Lock ....................................................................................................................................10
4.2 USB Model.........................................................................................................................................11
Mini USB Connector............................................................................................................................11
Alternate USB Header.........................................................................................................................11
Alternate Power Connector ................................................................................................................11
4.3 RS422 Model.....................................................................................................................................12
RS422 Header......................................................................................................................................12
Alternate Power Connector ................................................................................................................12
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4.4 GLK Model.........................................................................................................................................13
Keypad Header....................................................................................................................................13
4.5 GLT Model.........................................................................................................................................14
Touch Screen.......................................................................................................................................14
Coordinate Mode................................................................................................................................14
Region Mode.......................................................................................................................................14
4.6 Common Features.............................................................................................................................15
General Purpose Outputs ...................................................................................................................15
Dallas One-Wire Connector ................................................................................................................15
5 Troubleshooting.......................................................................................................................................16
5.1 Power ................................................................................................................................................16
5.2 Display...............................................................................................................................................16
5.3 Communication.................................................................................................................................17
5.4 Manual Override...............................................................................................................................17
6 Commands ...............................................................................................................................................18
6.1 Communication.................................................................................................................................18
Text .........................................................................................................................................................20
6.2 Drawing.............................................................................................................................................22
6.3 Fonts..................................................................................................................................................27
Font File Creation................................................................................................................................28
6.4 Bitmaps .............................................................................................................................................30
Bitmap File Creation............................................................................................................................31
Bitmap Masking ..................................................................................................................................31
6.5 9-Slices ..............................................................................................................................................32
9-Slice File Creation.............................................................................................................................32
6.6 Animations ........................................................................................................................................33
Animation File Creation ......................................................................................................................34
6.7 General Purpose Output...................................................................................................................34
6.8 Dallas One-Wire ................................................................................................................................35
6.9 Piezo Buzzer ......................................................................................................................................36
6.10 Keypad.............................................................................................................................................36
6.11 Touchpad ........................................................................................................................................38
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6.12 Display Functions ............................................................................................................................41
6.13 Scripting ..........................................................................................................................................42
6.14 Filesystem .......................................................................................................................................43
File Transfer Protocol..........................................................................................................................46
XModem Upload Protocol ..................................................................................................................47
6.15 Data Security...................................................................................................................................49
6.16 Miscellaneous .................................................................................................................................49
7 Appendix ..................................................................................................................................................52
7.1 Command Summary .........................................................................................................................52
7.2 Block Diagram ...................................................................................................................................57
7.3 Environmental Specifications............................................................................................................57
7.4 Electrical Tolerances .........................................................................................................................57
7.5 Dimensional Drawings ......................................................................................................................58
7.1 Optical Characteristics ......................................................................................................................60
8 Ordering ...................................................................................................................................................60
8.1 Part Numbering Scheme...................................................................................................................60
8.2 Options..............................................................................................................................................60
8.3 Accessories........................................................................................................................................61
9 Definitions................................................................................................................................................63
10 Contact...................................................................................................................................................63
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 1
1Introduction
Figure 1: GLT24064 Display
The GLK24064-25/GLT24064 is an intelligent graphic liquid crystal display engineered to quickly and
easily add an elegant creativity to any application. In addition to the RS232, TTL and I2C protocols
available in the standard model, USB and RS422 communication models allow the GLK24064-
25/GLT24064 to be connected to a wide variety of host controllers. Communication speeds of up to
115.2kbps for serial protocols and 100kbps for I2C ensure lightning fast text and graphic display.
The simple command structure permits easy software control of many settings including backlight
brightness, screen contrast, and baud rate. On board memory provides a whopping 256KB of
customizable fonts and bitmaps to enhance the graphical user experience.
User input on the GLK24064-25 is available through a five by five matrix style keypad, or a resistive
touch overlay on the GLT24064. Six general purpose outputs provide simple switchable five volt sources
on each model. In addition, a versatile Dallas One-Wire header provides a communication interface for
up to thirty-two devices.
The versatile GLK24064-25/GLT24064, with all the features mentioned above, is available in a variety of
colour, voltage, and temperature options to suit almost any application.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

2 Command Summary
2Quick Connect Guide
2.1 Available Headers
Figure 2: GLK24064-25/GLT24064 Header Locations
Table 1: List of Available Headers
#
Header
Mate
Population
1
RS422 Terminal Block
16-30 AWG Wire
422 Model Only
2
Extended Communication/Power Connector
ESCCPC5V/BBC
Standard Model Only
3
Alternate Power Connector
PCS
422 and USB Models Only
4
Mini USB Connector
EXTMUSB3FT/INTMUSB3FT
USB Model Only
5
GPO Header
None Offered
All Models
6
DB9 Serial Header
CSS1FT/CSS4FT
Standard Model Only
7
Keypad
KPP4x4
GLK Model Only
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 3
2.2 Standard Module
The standard version of the GLK24064-25/GLT24064 allows for user configuration of two common
communication protocols. First, the unit can communicate using serial protocol at either RS323 or TTL
voltage levels. Second, it can communicate using the Inter-Integrated Circuit connect, or I2C protocol.
Connections for each protocol can be accessed through the six pin Extended Communication/Power
Header as outlined in the Serial Connections and I2C Connections sections below.
Recommended Parts
Figure 3: Extended Communication/Power
Cable (ESCCPC5V)
The most common cable choice for any standard Matrix Orbital
display, the Extended Communication/ Power Cable offers a simple
connection to the unit with familiar interfaces. DB9 and floppy power
headers provide all necessary input to drive your display.
Figure 4: Breadboard Cable (BBC)
For a more flexible interface to the GLK24064-25/GLT24064, a
Breadboard Cable may be used. This provides a simple four wire
connection that is popular among developers for its ease of use in a
breadboard environment.
Serial Connections
Serial protocol provides a classic connection to the GLK24064-25/GLT24064. The Extended
Communication/Power Cable is most commonly used for this set up as it provides connections for DB9
serial and floppy power cables. To place your board in Serial mode, adhere to the steps laid out below.
1. Set the Protocol Select jumpers.
RS232: Connect the five jumpers*in the 232 protocol box with the zero ohm jumper resistors
provided or an alternate wire or solder solution.
TTL: Connect the four jumpers*in the TTL protocol box.
*Note: Jumpers must be removed from all protocol boxes save for the one in use.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4 Command Summary
2. Make the connections.
a. Connect the six pin female header of the Extended Communication/Power Cable to the
Communication/Power Header of your GLK24064-25/GLT24064.
b. Insert the male end of your serial cable to the corresponding DB9 header of the Extended
Communication/Power Cable and the mate the female connector with the desired
communication port of your computer.
c. Select an unmodified floppy cable from a PC power supply and connect it to the power header
of the Communication/Power Cable.
3. Create.
MOGD# or a terminal program will serve to get you started, and then you can move on with
your own development. Instructions for the former can be found below and a variety of
application notes are available for the latter at www.matrixorbital.ca/appnotes.
I2C Connections
A more advanced connection to the GLK24064-25/GLT24064 is provided by the I2C protocol setting. This
is best accomplished using a breadboard and the Breadboard Cable. Power must be supplied from your
breadboard or another external source. To dive right into your application and use the GLK24064-
25/GLT24064 in I2C mode, get started with the guidelines below.
1. Set the Protocol Select switches.
I2C: Ensure that the two I2C jumpers in the corresponding protocol box are connected while all
others are open.
2. Make the connections.
a. Connect the Breadboard Cable to the Communication/Power Header on your GLK24064-
25/GLT24064 and plug the four leads into your breadboard. The red lead will require power,
while the black should be connected to ground, and the green and yellow should be connected
to your controller clock and data lines respectively.
b. Pull up the clock and data lines to five volts using a resistance between one and ten kilohms on
your breadboard.
3. Create.
This time you're on your own. While there are many examples within the Matrix Orbital
AppNote section, www.matrixorbital.ca/appnotes, too many controllers and languages exist to
cover them all. If you get stuck in development, it is possible to switch over to another protocol
on the standard board, and fellow developers are always on our forums for additional support.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 5
2.3 USB Module
The GLK24064-25-USB/GLT24064-USB offers a single USB protocol for easy connection to a host
computer. The simple and widely available protocol can be accessed using the on board mini B style
USB connector as outlined in the USB Connections section.
Recommended Parts
Figure 5: Mini USB Cable
(EXTMUSB3FT)
The External Mini USB cable is recommended for the GLK24064-25-
USB/GLT24064-USB display. It will connect to the miniB style header on the
unit and provide a connection to a regular A style USB connector, commonly
found on a PC.
USB Connections
The USB connection is the quickest, easiest solution for PC development. After driver installation, the
GLK24064-25-USB/GLT24064-USB will be accessible through a virtual serial port, providing the same
result as a serial setup without the cable hassle. To connect to your GLK24064-25-USB/GLT24064-USB
please follow the steps below.
1. Set the Protocol Select jumpers.
USB: The GLK24064-25-USB/GLT24064-USB offers USB protocol only. Model specific hardware
prevents this unit from operating in any other protocol, and does not allow other models to
operate in USB. Protocol Select jumpers on the USB model cannot be moved.
2. Make the connections.
Plug the mini-B header of your External Mini USB cable into your GLK24064-25-USB/GLT24064-
USB and the regular USB header into your computer USB jack*.
3. Install the drivers.
a. Download the latest drivers at www.matrixorbital.ca/drivers, and save them to a known
location.
b. When prompted, install the USB bus controller driver automatically
c. If asked, continue anyway, even though the driver is not signed
d. When the driver install is complete, your display will turn on, but communication will not yet be
possible.
e. At the second driver prompt, install the serial port driver automatically
f. Again, if asked, continue anyway
4. Create.
Use MOGD# or a terminal program to get started, and then move on with your own
development. Instructions for the former can be found below and a number of application
notes are available for the latter at www.matrixorbital.ca/appnotes.
*Note: The YG version of the GLK24064-25-USB/GLT24064-USB will require the alternate power connection.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6 Command Summary
2.4 RS422 Module
The GLK24064-25-422/GLT24064-422 provides an industrial alternative to the standard RS232
communication protocol. Rather than single receive and transmit lines, the RS422 model uses a
differential pair for the receive and transmit signals to reduce degradation and increase transmission
lengths. Power can be transmitted at distance to a -VPT module or supplied from the immediate vicinity
to a regular or -V unit. RS422 signals are available in a six pin connector as described in the RS422
Connections section.
RS422 Connections
The GLK24064-25-422/GLT24064-422 provides a robust RS422 interface to the display line. For this
interface, a series of six wires are usually screwed into the RS422 terminal block provided. An alternate
header is also available to provide local power to a regular or -V unit. To connect to your GLK24064-25-
422/GLT24064-422, adhere to the steps laid out below.
1. Set the Protocol Select jumpers.
RS422: The GLK24064-25-422/GLT24064-422 offers only RS422 protocol and does not require
any jumper changes.
2. Make the connections.
a. Screw one wire; sized 16 to 30 on the American Wire Gauge, into each of the six terminal block
positions. When local power is supplied, a floppy cable may link to the alternate power header.
b. Connect the Vcc wire to the positive terminal of your power supply and the GND terminal to
the negative or ground lead to provide appropriate power as per Voltage Specifications.
c. Secure the A and B wires to your non-inverting and inverting output signals respectively, while
attaching the Z and Y wires to your inverting and non-inverting inputs.
3. Create.
a. In a PC environment, MOGD# or a terminal program will serve to get you started. In addition, a
variety of application notes are available online in a number of different languages to aid in the
development of a host controller. Instructions for these programs can be found below and the
simple C# example at www.matrixorbital.ca/appnotes is a great first programming reference.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 7
3Software
The multiple communication protocols available and simple command structure of the GLK24064-
25/GLT24064 means that a variety of applications can be used to communicate with the display. Text is
sent to the display as a character string, for example, sending the decimal value 41 will result in an 'A'
appearing on the screen. A single control character is also available. Commands are merely values
prefixed with a special command byte, 254 in decimal.
Table 2: Reserved Control Characters
Control Characters
7
Bell / Sound Buzzer
10
Line feed / New line
Once the correct communication port is identified, the following communication settings can be applied
to communicate correctly with the GLK24064-25/GLT24064.
Table 3: Communication Settings
BPS
Data Bits
Parity
Stop Bits
Flow Control
19200
8
None
1
None
Finally, with a communication port identified and correctly setup simple text strings or even command
bytes can easily be transmitted to control your display.
3.1 MOGD#
The Matrix Orbital Graphic Display interface, MOGD#, is offered as a free download from
www.matrixorbital.ca/software/software_graphic. It provides a simple graphical interface that allows
settings, fonts, and bitmaps to be easily customised for any application.
While monochromatic bitmaps can easily be created in virtually any image editing program, MOGD#
provides an extensive font generation suite to stylize your display to any project design. In addition to
standard font wide modifications, character ranges can be specified by start and end values to eliminate
unused symbols, and individual glyphs can be modified with a double click. Finally, text spacing can be
tailored and a complete font library built with your Matrix Orbital graphic display.
Like uProject, MOGD# offers a scripting capability that provides the ability to stack, run, and save a
series of commands. The most basic function is the Send Numeric tool which is used to transmit a string
of values to the display to write text or execute a command.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

8 Command Summary
Figure 6: MOGD# Command Example
Again, the clear screen command is sent to a connected display, this time using the MOGD# Send
Numeric function command style. Scripts can be run as a whole using the Play button from the toolbar
or as single commands by selecting Step; once executed it must be Reset. Before issuing commands, it is
a good idea to ensure communication with a display is successful using the autodetect button.
This program provides both a staging areas for your graphics display and a proving ground that will
prepare it for any application environment.
3.2 Firmware Upgrade
Beginning with revision 8.1, the firmware of the GLK24064-25/GLT24064 can be upgraded in the field.
All firmware revisions can be installed using software found at www.matrixorbital.ca/software/GLT
Series.
If it is necessary to forgo all current and future upgrades to the filesystem and subsequent commands,
firmware revision 8.0 may be ordered as a part of a custom order. Please use the
Contact section to request more information from the Matrix Orbital sales team.
3.3 Application Notes
Full demonstration programs and code are available for Matrix Orbital displays in the C# language from
Simple C# AppNote Pack in the Application Note section at www.matrixorbital.ca/appnotes. Difficulty
increases from beginner, with the Hello World program, to advanced with the Dallas One-Wire
temperature reading application.
Many additional applications are available in a number of different programming languages. These
programs are meant to showcase the capability of the display and are not intended to be integrated into
a final design. For additional information regarding code, please read the On Code document also found
on the support site.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 9
4Hardware
4.1 Standard Model
Extended Communication/Power Header
Figure 7: Extended Communication/Power Header
Table 4: Extended Communication/Power Pinout
Pin
Function
1
Vcc
2
Rx (SCL)
3
Tx (SDA)
4
Gnd
5
CTS
6
RTS
The Extended Communication/Power Header provides a standard connector for interfacing to the
GLK24064-25/GLT24064. Voltage is applied through pins one and four of the four pin
Communication/Power Header. Please ensure the correct voltage input for your display by referencing
Voltage Specifications before connecting power. Pins two and three are reserved for serial transmission,
using either the RS-232/TTL or clocking data through the I²C protocol, depending on what has been
selected by the Protocol Select Jumpers. Pins five and six can be used for serial transmission hardware
flow control, and are ignored for I²C communications. The Molex 22-04-1061 style header used can be
mated to a number of connectors, a 22-01-1062 for example.
Serial DB9 Connector
Figure 8: Serial DB9 Connector
Table 5: Serial DB9 Pinout
Pin
Function
2
Tx
3
Rx
5
Gnd
7
CTS
8
RTS
9
NC/Vcc*
The GLK24064-25/GLT24064 provides a DB-9 Connector to readily interface with serial devices using
EIA232 standard signal levels. It is also possible to communicate at TTL levels of 0 to +5V by setting the
Protocol Select Jumpers to TTL. As an added feature it is also possible to apply power through pin 9 of
the DB-9 Connector in order to reduce cable clutter. A standard male DB9 header will provide the
perfect mate for this connector.
*Note: Do not apply voltage through pin 9 of the DB-9 Connector AND through the Communication/Power Header
at the same time.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

10 Command Summary
Power Through DB9 Jumper
In order to provide power through pin 9 of the DB-9 Connector you must connect the Power Through
DB-9 Jumper labelled R42, as illustrated below. This connection can be made using a zero ohm resistor,
recommended size 0603, or a solder bridge. The GLK24064-25/GLT24064 allows all voltage models to
use the power through DB-9 option, see the Voltage Specifications for power requirements.
Figure 9: Power Through DB9 Jumper
Protocol Select Jumpers
The Protocol Select Jumpers provide the means necessary to toggle the GLK24064-25/GLT24064
between RS-232, TTL and I²C protocols. As a default, the jumpers are set to RS-232 mode with solder
jumps on the RS232 jumpers. In order to place the display module in I²C mode you must first remove
the solder jumps from the RS232 jumpers and then place them on the I2C jumpers. The display will now
be in I²C mode and have a default slave address of 80, unless changed with the appropriate command.
Similarly, in order to change the display to TTL mode, simply remove the zero ohm resistors from the
RS232 or I²C jumpers and solder them to the TTL jumpers.
Hardware Lock
The Hardware Lock allows fonts, bitmaps, and settings to be saved, unaltered by any commands. By
connecting the two pads near the memory chip, designated R13, with a zero ohm resistor, the display
will be locked. This supersedes the data lock command and cannot be circumvented by any software
means. To unlock the display and make changes simply remove the jumper.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 11
4.2 USB Model
Mini USB Connector
Figure 10: Mini USB Connector
Table 6: Mini USB Pinout
Pin
Function
1
Vcc
2
D-
3
D+
5
Gnd
The GLK24064-25-USB/GLT24064-USB comes with a familiar Mini USB Connector to fulfill both
communication and power needs*. The standard MiniB style header can be connected to any other USB
style using the appropriate cable. Most commonly used with a PC, this connection creates a virtual com
port that offers a simple power solution with a familiar communication scheme.
Alternate USB Header
Some advanced applications may prefer the straight four pin connection offered through the Optional
Alternate USB Header. This header offers power and communication access in a simple interface
package. The Optional Alternate USB Header may be added to the GLK24064-25-USB/GLT24064-USB for
an added charge as part of a custom order. Please use the
Contact section to request more information from the friendly Matrix Orbital sales team.
Alternate Power Connector
Figure 11: Alternate Power Connector
Table 7: Alternate Power Pinout
Pin
Function
1
Vcc
2
Gnd
3
Gnd
4
NC
The Alternate Power Connector provides the ability to power the GLK24064-25-USB/GLT24064-USB
using a second cable*. The Tyco 171825-4 style header is particularly useful for connecting to an
unmodified floppy power cable, a 171822-4 for example, from a PC power supply for a simple bench
power solution.
*Note: The YG version of the GLK24064-25-USB/GLT24064-USB may draw more than the 500mA of current
permitted by USB standards and will likely require the alternate power connection.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

12 Command Summary
4.3 RS422 Model
RS422 Header
Figure 12: RS422 Header
Table 8: RS422 Pinout
Pin
Function
1
Gnd
2
Rx (Y)
3
Inv Rx (Z)
4
Inv Tx (B)
5
Tx (A)
6
Vcc
The six pin RS422 interface header of the GLK24064-25-422/GLT24064-422 offers power and ground
connections as well as two differential pair communication lines. Regular and inverted lines are
provided for both receive and transmit signals. Power is supplied locally to the regular or –V variants
while the –VPT can receive power over a distance. The Tyco 282834-6 style header is most suited to a
simple wire connection.
Alternate Power Connector
Figure 13: Alternate Power Connector
Table 9: Alternate Power Pinout
Pin
Function
1
Vcc
2
Gnd
3
Gnd
4
NC
The Alternate Power Connector provides the ability to power the GLK24064-25-USB/GLT24064-USB
using a second cable. The Tyco 171825-4 style header is particularly useful for connecting to an
unmodified floppy power cable, a 171822-4 for example, from a PC power supply for a simple bench
power solution.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 13
4.4 GLK Model
Keypad Header
Figure 14: Keypad Header
Table 10: Keypad Pinout
Pin
Function
Pin
Function
1
Gnd
7
Column 1
2
Row 1
8
Column 2
3
Row 2
9
Column 3
4
Row 3
10
Column 4
5
Row 4
11
Column 5
6
Row 5
12
Gnd/Vcc*
To facilitate user input, the GLK24064-25 provides a Keypad Interface Connector which allows a matrix
style keypad of up to twenty-five keys to be directly connected to the display module. Key presses are
generated when a short is detected between a row and a column. When a key press is generated, a
character specific to that key press is automatically sent on the Tx communication line. If a synchronous
read method is desired in serial mode*, the “Auto Transmit Keypress” function can be turned off to
allow the key presses to remain in the buffer so that they may be polled. The character that is
associated with each key press may also be altered using the “Assign Key Codes” command. The straight
twelve pin header of the Keypad Interface Connector will interface to a variety of different devices
including the Matrix Orbital KPP4x4 keypad.
*Note: In I2C mode, the “Auto Transmit Keypress” function should always be on, keypresses should not be polled.
**Note: The Ground/+5V pin is toggled by the jumpers to the right of the keypad connector. Placing a 0 Ohm
resistor on jumper R31 ties pin 12 to Ground. Using a 0 Ohm resistor on jumper R29 supplies +5V to pin 12. It
should be noted that only 1 jumper should be occupied at a time, otherwise a short will be created.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

14 Command Summary
4.5 GLT Model
Touch Screen
The GLT24064 facilitates user touch input in one of two distinct ways. Coordinate mode will report
events by supplying their exact position on the screen. Region mode will report events within defined
boundaries on the screen. Both modes are outlined below.
Coordinate Mode
In coordinate mode all touch events are reported using three
single byte values. First, the type of event is transmitted,
followed by the x and y coordinates of its position. Pressure
and drag thresholds must be exceeded for an event to be
registered. A low drag threshold will result in greater tracking
accuracy but transmits much more data to the host. Care
should be taken to find balance. This mode offers a great
degree of flexibility and creativity.
Table 11: Coordinate Mode Event Prefixes
Return Value
1
2
4
Touch Event
Press
Release
Drag
Region Mode
A simpler, keypad style alternative to coordinate mode,
region mode offers only a single byte for each touch event.
Unique regions are created by specifying a position, size, and
return values. A value corresponding to a specific region is
returned when an event occurs within its bounds. Events
outside of regions result in transmission of the value 255.
Regions can be deleted individually or collectively when no
longer needed. This mode allows quick and easy set up.
Table 12: Region Mode Event Responses
Return Value
Key Down
Key Up
Key Down
255
Touch Event
Press
Release
Drag
Out of Region
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Command Summary 15
4.6 Common Features
General Purpose Outputs
Figure 15: GPO Header
Table 13: GPO Pinout
Pin
Function
Pin
Function
1
GPO 1
8
Gnd
2
GPO 2
9
Gnd
3
GPO 3
10
Gnd
4
GPO 4
11
Gnd
5
GPO 5
12
Gnd
6
GPO 6
13
Gnd
7
Vcc
14
Gnd
A unique feature of the GLK24064-25/GLT24064 is the ability to control relays*and other external
devices using either one or six General Purpose Outputs. Each can source up to 10mA of current at five
volts when on or sink 20mA at zero volts when off. The two row, fourteen pin header can be interfaced
to a number of female connectors to provide control to any peripheral devices required.
*Note: If connecting a relay, be sure that it is fully clamped using a diode and capacitor in order to absorb any
electro-motive force (EMF) which will be generated.
Dallas One-Wire Connector
Figure 16: Dallas One-Wire Connector
Table 14: Dallas One-Wire Pinout
Pin
Function
1
Vcc
2
D
3
Gnd
In addition to the six general purpose outputs the GLK24064-25/GLT24064 offers an Optional Dallas
One-Wire bridge, to allow for an additional thirty two one-wire devices to be connected to the display.
This header can be populated with a Tyco 173979 connector at an added cost by custom order only.
Please use the Contact section to request more information from the Matrix Orbital sales team.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.