MATSONIC MS7192S User manual

This publication, including all photographs, illustrations and
software, is protected under international copyright laws, with all
rights reserved. Neither this manual, nor any of the material
contained herein, may be reproduced without the express written
consent of the manufacturer.
The information in this document is subject to change without
notice. The manufacturer makes no representations or warranties
with respect to the contents hereof and specifically disclaims any
implied warranties of merchantability or fitness for any particular
purpose. Further, the manufacturer reserves the right to revise this
publication and to make changes from time to time in the content
hereof without obligation of the manufacturer to notify any person
of such revision or changes.
Trademarks
IBM, VGA, OS/2, and PS/2 are registered trademarks of
International Business Machines.
Intel, Pentium, Pentium-II, Pentium-III, MMX, and Celeron are
registered trademarks of Intel Corporation.
Microsoft, MS-DOS and Windows 95/98/NT are registered
trademarks of Microsoft Corporation.
Sound Blaster and SB-Link are trademarks of Creative Technology
Ltd.
PC-cillin and ChipAway Virus are trademarks of Trend Micro Inc.
Award is a trademark of Award Software Inc.
A3D is a registered trademark of Aureal Inc.
Other names used in this publication may be trademarks and are
acknowledged.
Copyright © 1999
All Rights Reserved
MS7192S, Version 1.2
V6X/April 1999

Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
qReorient or relocate the receiving antenna.
qIncrease the separation between the equipment and the receiver.
qConnect the equipment onto an outlet on a circuit different from that
to which the receiver is connected.
qConsult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and shielded AC power cable must be
employed with this equipment to insure compliance with the pertinent RF
emission limits governing this device. Changes or modifications not
expressly approved by the system’s manufacturer could void the user’s
authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject
to the following conditions:
qThis device may not cause harmful interference, and
qThis device must accept any interference received, including
interference that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian
Interference-causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouilieur du Canada.

Table of Contents
Chapter 1 Introduction........................................................1
Key Features................................................................................. 2
Slot-1 Processor Support........................................................... 2
Socket-370 Processor Support................................................... 2
Memory Support....................................................................... 2
Expansion Slots ........................................................................ 2
Onboard IDE channels .............................................................. 2
Power Supply and Power Management ...................................... 3
Sound System........................................................................... 3
Onboard I/O Ports..................................................................... 3
Hardware Monitoring................................................................ 4
Onboard Flash ROM................................................................. 4
Bundled Software ..................................................................... 4
Dimensions............................................................................... 4
Package Contents .......................................................................... 4
Optional Accessories ................................................................ 4
Static Electricity Precautions ......................................................... 5
Chapter 2 Mainboard Installation.......................................6
Mainboard Components ................................................................ 7
I/O Ports....................................................................................... 8
Install the Processor ...................................................................... 8
Installing a Slot-1 Processor Cartridge ....................................... 9
Installing a Socket-370 Processor .............................................10
Install Memory.............................................................................11
Set the Jumpers ............................................................................12
Jumper JP1: Clear CMOS Memory ..........................................13
Jumper JP2: Keyboard Power On Selector................................13
Jumper JP3: Audio System Enable/disable ...............................13
Jumper JP4: Select System Bus Frequency ...............................13
Jumper JP5: Set SPDIF Output Voltage....................................14
Jumper JP7: Flash BIOS Enable/disable ...................................14
Install the Mainboard ...................................................................15
Install the Extension Brackets/Options .........................................16
Digital Audio Extension Bracket ..............................................16
Optional Infrared Port ..............................................................17
Install Other Devices ....................................................................18
Floppy Disk Drive ...................................................................18
IDE Devices ............................................................................18

Table of Contents
Internal Sound Connections .................................................... 19
Expansion Slots .......................................................................... 20
Installing an Expansion Card ................................................... 20
Wake Up Connectors and Sideband1 ....................................... 21
Wake On LAN........................................................................ 21
Wake On Modem.................................................................... 21
SB-Link.................................................................................. 21
Chapter 3 BIOS Setup.......................................................22
Introduction ................................................................................ 22
Running the Setup Utility ............................................................ 23
Standard CMOS Setup Page........................................................ 24
BIOS & CPU Features Setup Page .............................................. 25
Chipset Features Setup Page........................................................ 27
Power Management Setup Page ................................................... 29
PCI / Plug and Play Setup Page ................................................... 31
Load BIOS Defaults.................................................................... 32
Load Optimum Settings ............................................................... 32
Integrated Peripherals Setup Page ................................................ 33
Password Settings ....................................................................... 35
Change or Remove the Password ............................................. 35
IDE HDD Auto Detection ........................................................... 35
Save and Exit Setup .................................................................... 35
Exit Without Saving Option ........................................................ 36
Chapter 4 Software & Applications...................................37
Introduction ................................................................................ 37
Using the PCI Sound Application ................................................ 37
The Four Speakers System .......................................................... 38
Speaker Installation ................................................................. 38
Speaker Position ..................................................................... 38
Mixer Setup............................................................................ 39
Demo...................................................................................... 39

Chapter 1
Introduction
This mainboard provides very high performance as it supports all
of Intel’s Slot-1 processors including the Pentium-III, the
Pentium-II, and the SEPP (Single Edge Processor Package)
Celeron. Pentium-III processors run at clock rates of 450 and 500.
Pentium-II processors run from 233 MHz through to 450 MHz, and
the SEPP Celerons run from 266 up to 433 MHz. The mainboard
also has a Socket-370 for the new PPGA (Plastic Pin Grid
Array) Celeron processor.
The mainboard is highly integrated and includes a built-in PCI 3D
Sound System. In addition, the mainboard has a full set of ATX
I/O Ports including two serial ports, two PS/2 ports, a parallel port
and two USB ports.
The mainboard supports CPU Plug & Play through firmware. The
board adheres to the ATX Form Factor and it can be installed in
an ATX. The board is installed with a full set of expansion slots
including an AGP slot for an AGP graphics adapter, four 32-bit
PCI slots, and two 8/16-bit legacy ISA slots.

Chapter 1
2
Key Features
This key features of this mainboard include:
Slot-1 Processor Support
♦Pentium-III support for 450 MHz and 500 MHz clock
rates
♦Pentium-II support for 233 MHz to 450 MHz clock rates
♦SEPP Celeron support for 266 MHz to 433 MHz clock
rates
♦Support for 66 MHz and 100 MHz FSB (Front Side Bus)
♦All processors configured by CPU Plug & Play
Socket-370 Processor Support
♦Supports the new PPGA Celeron processor
♦Supports the PPGA Celeron 66 MHz bus
♦All processors configured by CPU Plug and Play
Memory Support
♦Three DIMM slots for 3V SDRAM 168-pin memory
modules
♦Support for 66 MHz and 100 MHz memory bus
♦Supports 1-bit ECC (Error Correction Code)
♦Maximum installed memory can be 3 x 256 MB = 768 MB
Expansion Slots
♦Four 32-bit PCI slots
♦One AGP slot for an AGP graphics adapter
♦Two 8/16-bit ISA slots
♦One PCI slot and one ISA slot are shared, meaning that
only one of the slots can be used at one time.
Onboard IDE channels
♦Primary and Secondary PCI IDE channels
♦Support for PIO (programmable input/output) modes
♦Support for Bus mastering and UltraDMA 33/66 modes

Key Features
3
Power Supply and Power Management
♦Provides ATX power connector
♦Support for Power button/Suspend Switch, and Keyboard
Power On/Off (needs Win98 keyboard)
♦Supports Wake on Modem, Wake on LAN and Wake on
Alarm
Sound System
♦Meets PC98 audio specification
♦Full duplex playback and recording with built-in 16-bit
CODEC
♦HRTF 3D professional audio supports both Direct Sound
3D® and A3D® interfaces compatible plus support for 4-
channel speakers
♦Drivers support Windows 3.1/95/98/NT 4.0
♦Built-in 32 ohm earphone buffer and 3D surround
♦Provides MPU-401 Game/MIDI port and legacy Sound
Blaster 16 support
♦Downloadable Wave-table Synthesizer supports Direct
Music®
♦Digital Audio Interface with 24-bit stereo, 44KHz
sampling rate and measured 120dB audio quality
♦Stereo Mixer supports analog mixing from CD-Audio,
Line-In, and digital mixing from voice, FM/Wave-table and
digital CD-Audio
Onboard I/O Ports
♦Provides PC99 Color Connector for easy identification of
peripheral devices
♦Floppy disk drive port with 1Mb/s transfer rate
♦Two serial port with 16550-compatible fast UART
♦One parallel port with support for ECP and EPP
♦Two USB ports & two PS/2 ports
♦One optional infrared port

Chapter 1
4
Hardware Monitoring
♦Built-in hardware monitoring for CPU temperature and fan
speeds
♦Supports Intel’s LANDesk Client Manager (LDCM)
Onboard Flash ROM
♦Provides plug and play function for automatic CPU and
board configuration
♦Supports plug and play configuration of peripheral devices
and expansion cards
♦Built-in virus protection using Trend’s ChipAway Virus
which ensures that the entire boot process is virus protected.
Bundled Software
♦PC-Cillin provides automatic virus protection under
Windows 95/98
Dimensions
♦ATX form factor (30.5cm x 22cm)
Package Contents
Your mainboard package ships with the following items:
qMainboard
qSlot-1 cartridge holder
qThis User’s guide
qIDE cable
qFloppy diskette drive cable
qSupport software CD-ROM
Optional Accessories
You can purchase the following optional accessories for this
mainboard.
qDigital Audio extension bracket
qInfrared port extension bracket

Static Electricity Precautions
5
Static Electricity Precautions
1. Components on this mainboard can be damaged by static
electricity. Take the following precautions when unpacking the
mainboard and installing it in a system.
2. Keep the mainboard, and other components, in their original
static-proof packaging until you are ready to install them.
3. During an installation, wear a grounded wrist strap if possible.
If you don’t have a wrist strap, frequently discharge any static
electricity by touching the bare metal of the system chassis.
4. Handle the mainboard carefully by the edges. Avoid touching
the components unless it is absolutely necessary. During the
installation lay the mainboard on top of the static-proof
packaging with the component side facing upwards.
5. Inspect the mainboard for any damage caused during transit.
Ensure that all the components that are plugged into sockets
are correctly seated.
6. If you suspect that the mainboard has been damaged, do not
apply power to the system. Contact your mainboard vendor
and report the damage.

Chapter 2
Mainboard Installation
To install this mainboard into your system, follow the procedures
in this chapter:
qIdentify the mainboard components
qInstall the correct processor
qInstall one or more memory modules
qVerify that any jumpers or switches are at the correct setting
qInstall the mainboard in the system chassis
qInstall any other devices and make the appropriate connections
to the mainboard headers.
Note: Before installing the mainboard, you must ensure that
jumper JP1 is set to the Normal setting. See this chapter for
information on locating JP1 and changing the jumper setting.

Mainboard Components
7
Mainboard Components
Use the diagram below to identify the major components on your
mainboard.
Slot-1
JP2
ATX1
Socket-370
CD1
CD2
JP3
JP5
SPDIF1
SIR1
AGP1
Sideband1
PCI1
PCI2
PCI3
PCI4
ISA1
ISA2
CPUFAN1
JP4
DIMM
DIMM2
DIMM3
FDD1
IDE1
IDE2
PANEL CASEFAN1
JP1
WOM1
WOL1
JP7

Chapter 2
8
I/O Ports
The illustration below shows a side view of the I/O ports installed
on the mainboard.
PS/2 Mouse
PS/2 Keyboard
USB Ports
Microphone
Game/MIDI Port
Stereo In
Parallel Port
Serial COM2/4
Serial COM1/3 Stereo Out
Install the Processor
This mainboard has a Slot-1 which can be installed with any Slot-1
processor cartridge including the Pentium-III, the Pentium-II, and
the SEPP Celeron. It also has a Socket-370 which can be installed
with the new Celeron processor which is shipped in a PPGA
(Plastic Pin Grid Array) package. To ensure reliability, make
sure that your PPGA Celeron processor is fitted with a
heatsink/cooling fan assembly.
You can install a Slot-1 processor or a PPGA Celeron. You cannot
install a PPGA and a Slot-1 processor cartridge together. Take care
that you do not try to install a Socket-7 processor into the Socket-
370. A Socket-7 processor such as the Pentium-MMX, or the AMD
K5/K6 does not fit in the socket-370.
The following table lists all the processors that are currently
supported by the two processor sockets. New processors may be a
released after this manual is printed.

Install the Processor
9
Processor
Cartridge Clock Rate MHz Processor Socket System Bus MHz
Pentium-III 500 Slot-1 100
Pentium-III 450 Slot-1 100
Pentium-II 450 Slot-1 100
Pentium-II 400 Slot-1 100
Pentium-II 350 Slot-1 100
Pentium-II 333 Slot-1 66
Pentium-II 300 Slot-1 66
Pentium-II 266 Slot-1 66
Pentium-II 233 Slot-1 66
SEPP Celeron 433 Slot-1 66
SEPP Celeron 400 Slot-1 66
SEPP Celeron 366 Slot-1 66
SEPP Celeron 333 Slot-1 66
SEPP Celeron 300A Slot-1 66
SEPP Celeron 300 Slot-1 66
SEPP Celeron 266 Slot-1 66
PPGA Celeron 433 Socket-370 66
PPGA Celeron 400 Socket-370 66
PPGA Celeron 366 Socket-370 66
PPGA Celeron 333 Socket-370 66
PPGA Celeron 300 Socket-370 66
Installing a Slot-1 Processor Cartridge
1. Locate Slot-1 and CPUFAN1on the mainboard.
2. The Slot-1 is installed with a cartridge holder. The upright
struts of the cartridge holder are folded down for shipping. Pull
the struts upwards so that they are in the upright position.
Slot-1 with pre-installed
cartridge holder. The
upright arms are folded
down for shipping.
CPUFAN1

Chapter 2
10
3. Insert the processor cartridge into the cartridge holder. Follow
the instructions given with your processor cartridge. The edge
connector on the cartridge has a notch so that it only fits into
the Slot-1 in the correct way.
4. Locate the cooling fan power supply CPUFAN1. Connect the
cable from the processor cartridge cooling fan to FAN1.
5. On this mainboard, you can configure the processor by
entering the correct settings in the BIOS setup utility.
Installing a Socket-370 Processor
The Celeron processor installs into the ZIF (Zero Insertion Force)
Socket-370 on the mainboard.
1. Locate the Socket-370 and CPUFAN1. Pull the locking lever
out from the socket and swing it to the upright position.
Pin-1 Corner
CPUFAN1
Socket-370

Install Memory
11
2. On the Celeron processor, identify the pin-1 corner by noting
that it has a slight bevel.
3. On the Socket-370, identify the pin-1 corner. The pin-1 corner
is on the same side as the locking lever, closest to the top of the
lever when it is in the locked position.
4. Match the pin-1 corners and insert the Celeron processor into
the socket. No force is required and the processor should drop
into place freely.
5. Swing the locking lever down and hook it under the catch on
the side of the socket. This locks the Celeron processor in the
socket.
If the Celeron processor is installed with a cooling fan assembly,
connect the cable from the fan to the CPU fan power connector
CPUFAN1.
Install Memory
The mainboard has three DIMM slots which can be installed with
memory modules. You must install at least one memory module in
order to use the mainboard. You can install the memory into any of
the DIMM slots.
For this mainboard, you must use 168-pin, 3.3V memory modules
installed with SDRAM memory chips. If you are using a processor
cartridge that runs on a 100 MHz system bus, you must use
memory that operates on a 100 MHz memory bus (PC-100
memory). If you are using a processor cartridge that runs on a 66
MHz system bus, you can use memory that operates on a 66 MHz
memory bus.
DIMM1
DIMM2
DIMM3

Chapter 2
12
You can install any size of memory module from 16 MB up to 256
MB, so the maximum memory size is 3 x 256 MB = 768 MB.
The edge connectors on the memory modules have cut outs, which
coincide with struts in the DIMM slots, so the memory modules
can only be installed in the correct way.
On the DIMM slot, pull the locking latches at either end of the
slots outwards. Position the memory module correctly and insert it
into the DIMM slot. Press the module down into the slot so that the
locking latches lever inwards and lock the module in place.
Set the Jumpers
Jumpers are sets of pins which can be connected together with
jumper caps. The jumper caps change the way the mainboard
operates by changing the electronic circuits on the mainboard. If a
jumper cap connects two pins, we say the pins are SHORT. If a
jumper cap is removed from two pins, the pins are OPEN.
JP2
JP4
JP1
JP7
JP5
JP3
1
1
1
1
1

Set the Jumpers
13
Jumper JP1: Clear CMOS Memory
Use this jumper to clear the contents of the CMOS memory. You
may need to clear the CMOS memory if the settings in the setup
utility are incorrect and prevent your mainboard from operating. To
clear the CMOS memory, disconnect all the power cables from the
mainboard and then move the jumper cap into the CLEAR setting
for a few seconds.
Function Jumper Setting
Normal Operation Short Pins 1-2
Clear CMOS memory Short Pins 2-3
Jumper JP2: Keyboard Power On Selector
If you enable the keyboard power on feature, you can use hot keys
on your keyboard as a power on/off switch for the system
Note: Make sure that the system can provide 1A on +5VSB (+5V
Standby) signal before using the Keyboard Power On function.
Function Jumper Setting
Disable Keyboard Power On Short Pins 1-2
Enable Keyboard Power On Short Pins 2-3
Jumper JP3: Audio System Enable/disable
Use this jumper to enable or disable the audio system integrated on
this mainboard. Disable the built-in audionif you plan on using
another audio system on an expansion card.
Function Jumper Setting
Enable Audio Short Pins 1-2
Disable Audio Short Pins 2-3
Jumper JP4: Select System Bus Frequency
If you set this jumper to Normal, the system will auto-detect if the
installed processor requires a system bus speed of 66 MHz or 100
MHz. If you set this jumper to Force 100 MHz, the system will
always use a 100 MHz bus, even for processors that are rated to
run on a 66 MHz system bus frequency.

Chapter 2
14
Jumper JP5: Set SPDIF Output Voltage
Use this jumper to select the output voltage of the digital audio
SPDIF connector on this mainboard. Select either 0.5 volts or 5
volts according to the devices that you have connected to the
SPDIF connector.
Function Jumper Setting
5V SPDIF Output Short Pins 1-2
0.5V SPDIF Output Open Pins 1-2
Jumper JP7: Flash BIOS Enable/disable
The mainboard BIOS is stored on an EPROM (Erasable
Programmable Read Only Memory) chip. You can erase an old
BIOS and write an upgrade BIOS to the chip by using the Flash
BIOS utility. Before flashing a new BIOS, you must set this
jumper to Enable.
Function Jumper Setting
Enable flash BIOS Short Pins 1-2
Disable flash BIOS Short Pins 2-3

Install the Mainboard
15
Install the Mainboard
Install the mainboard into the system chassis. This mainboard uses
the ATX format with a twin-tier of I/O ports. Ensure that your case
has an I/O template that can be used by this mainboard.
Install the mainboard into the unit case. Follow the instructions
provided by the case manufacturer using the screws and mounting
points provided in the chassis.
Connect the power cable from the power supply unit to the power
connector ATX1 on the mainboard. If the system chassis is
installed with a cooling fan, connect the cable from the cooling fan
to the chassis fan power connector on the mainboard CASEFAN2.
Connect the case switches and indicator LEDs to the bank of
switch and LED connectors PANEL. See the illustration below for
a guide to the pin functions of the PANEL connector.
ATX1
CASEFAN1
Panel
123
HDD LED 20-21
Speaker 15-16-17-18
Reset SW 12-13
Power SW 22-23
Power LED 1-2-3 Green LED 7-8-9
Sleep SW 4-5
231
Keylock 10-11

Chapter 2
16
Install the Extension Brackets/Options
This mainboard does not ship with any extension brackets. You
can install an optional SPDIF extension bracket and an optional
infrared port.
The extension brackets are used to transmit features on the
mainboard to external connectors that can be fixed to the system
chassis. Follow the steps below to install the extension brackets.
Note: All the ribbon cables used on the extension brackets carry a
red stripe on the pin-1 side of the cable.
Digital Audio Extension Bracket
This bracket has two RCA jacks for digital audio in and digital
audio out, and an auxiliary jack for a Stereo Line-in device.
1. On the mainboard, locate the SPDIF1 header for this bracket.
2. Plug the cable from the bracket into the SPDIF1 header.
3. In the system chassis, remove a blanking plate from one of the
expansion slots and install the extension bracket in the slot.
Use the screw that held the blanking plate in place to secure
the extension bracket.
Stereo Line-in
SPDIF In
SPDIF Out
Digital Audio
Extension Bracket
SPDIF1
1