MAX SMART SG2 User manual
INSTALLATION AND USER MANUAL
Alarm Security System™
GSM+WiFi SG2
1. Status / GSM Signal Indicator
2. Power / Network status Indicator
3. Panic (SOS)
4. Panel
5. Stand
6. Monitoring MIC
SIM 1. SIM Card Slot
2. Connect
3. Power
4. Adapter Interface
5. USB Upgrade Port
2 3
-16-bit high speed processor, reliable capability
-100% wireless D.I.Y.
-Built-in 1,000,000 RF codes
-Supports 10 remote controls and 100 wireless sensors.
-The alarm system can be controlled by SMS, App or phone call
-Stores 5 phone numbers and 5 SMS numbers for alarm alert
-Supports exit and entry delay arm / alert
-Wireless self-learning code
-Adding new accessories fast and easy
-Supports arm and disarm by App
-Supports remote monitor by App
-Supports remote control / arm / disarm / monitor by phone
-SMS for power power recovery and low
-Supports global GSM 850/900/1800/1900MHz
-
Support Wi-Fi 802.11b/g/n
Control Panel Features
Features
1. Status / Low Power Indicator
Blue(off):system is disarmed
Blue system is armed
Blue (blinking): the alarm has been triggered
2. Power / GSM Signal Indicator
Product name:
SG2 GSM+WiFi
Power supply:
Input:AC 110~240V/50~60Hz
Output: DC 12V/1A
GSM working frequency:
850/900/1800/1900MHz
Standby current:
60mAh
Alarm current:
120mAh
Built-in
7.4V 500mAh lithium
Support wireless accessories:
10 remote control, 100 wireless detectors
Wireless receiving frequency:
315 MHz / 433MHz (±75KHz)
Siren volume:
90dB
Housing material:
ABS
Temperature: -10°C ~ +55°C
Humidity: ≤80%
(non-condensing)
White(Fast blinking):searching GSM network
White(slow blinking): GSM signal is normal
Wi-Fi:
802.11b/g/n
4 5
Quick Start-up Guide
Firstoperaons
Store a phone number
To interact with the control panel by SMS, by phone call and/or from the app, at least one phone number
Change the language
Arm / Disarm the system
By SMS
By app
Register wireless accessories
Control by Phone Call
Method 1
Method 2
Aer each key you press on your phone, you hear one beep
of conrmaon. Wait unl you have heard this beep of conrmaon before pressing the next key.
Note
VoiceInstrucons
Command
Press Arms the system
Press
- Stops monitoring without hanging up
Press
Press
Press
Press
- Exits control by phone call
- Stops call recycles
Note
Hard Reset
6
Zone setup of accessories
D0
D3
D0
D3
D0
D3 D3
D0
Normal zone
24h zone
It is recommended to set smoke detectors, gas detectors and outdoor beam sensors in the 24-H zone.
Delay zone
It is recommended to assign the Door /
Window Contact to the Delay zone.
Home zone
When the system is armed in Home Mode, the sensors assigned to the Home zone do not trigger an
It is recommend to assign moon dectors to the Home zone so that you can have your system
armed in Home Mode when you are home and move inside your home without triggering any alarm.
SMSOperaons
IMPORTANT: BEFORE USING FOR THE
FIRST TIME
Only stored numbers can control and
congure the system.
INSERT A SIM CARD IN THE CONTROL PANEL
SMS Command
The rst pink speech bubble is the SMS
command sent by the user
The rst grey speech bubble is the reply sent
by the control panel
The speech bubbles that follow are the
dialogue between the user and the control
panel (SMS sent by the user are in pink, SMS
sent by the control panel are in grey).
Store Phone numbers for SMS
nocaons
6
Copy, Paste, then Edit
8 9
Disarm the System
0
Arm the System
1
Home Mode
2
SengsEnquiry
00
Note
Store Phone Numbers
5
Copy, Paste, then Edit
Change Zone Name
9199
91
Copy, Paste, then Edit
Note
of the zone cannot consist of more than
10 11
SMSAlertforAccessoryLowBaery
been renamed, an SMS will be sent under
not been renamed, an SMS will be sent under
SMS Alert for Accessory Tamper Alarm
been renamed, an SMS will be sent under
tamper alarm
not been renamed, an SMS will be sent
tamper
alarm
Entry and Exit Delay Time
11
Copy, Paste, then Edit
Note
to bring a remote control or RFID tag with
Siren Volume and Ringing Time
12
Copy, Paste, then Edit
Note
Disarm Password
13
1234
Copy, Paste, then Edit
8888
Set Ringing Times
19
Copy, Paste, then Edit
1312
Callrepeon
the alarm detects an intrusion, the alarm will
20
Copy, Paste, then Edit
Delete all Wireless Accessories
21
Change system language
0001
0001
Refer to the table below for the full list of
0001 English
0002 French
0003 Russian
0004 Danish
0005 Dutch
0006 Italian
0007 Swedish
0008 German
0009 Spanish
0010 Finnish
0011 Norwegian
0012 Arabic
0013 Farsi
RestoreSystemtoFactorySengsbySMS
0000
Only stored numbers can send the SMS to
Accessories
Wireless Remote Control
Home Mode
Arm
SOS
Disarm
LED indicator
Arm the system
If an intruder is detected, the siren rings
system dials the pre-stored phone numbers
Disarm the system
Home Mode
All the sensors in regular zones are armed
The sensors in the Home Mode zone are
1514
Emergency Mode
Regardless the status of the system, the alarm
SOS
Register in the control panel
Specicaons
10 uA
Transmission distance
WirelessMoonDetector
Features
Design
3
1
2
1. LED indicator
2. Detection window
3. Bracket
PCB Layout
Alarm zone
setup
Tamper
switch*
Infrared
sensor**
AA 1.5V LR6
Antenna
LED working
indicator
*Tamper switch
When the alarm system is armed, the tamper
switch will trigger the alarm if the case is
**Infrared sensor
Detects the infrared rays released by human
LEDindicaons
Blinksconnuously:
Blinks once: an intruder is detected
Blinks twice:
Blinks once every 3 seconds:
16
Usage
When the sensor is in operation, if it is
triggered more than twice within 3 minutes,
it will switch to standby mode to save power.
If no movement is detected within the next
3 minutes, the sensor goes back to working
mode.
Register in the control panel
Installaon
recommended to mount the detector
Top
Ground
2.2 m
The detector is more sensitive to
cross movements than vertical
movements.
Tesng
Specicaons
Power supply
Alarm current
Housing material
DeteconScope
0m 2m 4m 6m 8m
2m
0m
1918
Wireless Door / Window Contact
Features
The ES-D3A is a Door / Window Contact that can be installed on doors, windows, and any other
Design
Magnet
Transmitter
LED indicator
PCB Layout
LED working indicator
Zone setting
A23 12V Battery
Tamper switch
LEDindicaons
Blinks once
Blinksquickly:
Register the detector in the alarm system
Installaon
-
- Mount the sensor on the door and the magnet on the
-
-
-
Specicaons
Power supply
Alarm current
Housing material
60 x 45 x 18 mm
2120
RegisteranAddionalSiren
TroubleshoongandSafetyInstrucons
FAQ
Issue
No response following
control panel
The control panel is switched
Turn the power on
AC Power failure
Accessories cannot
connect to the control
panel
The control panel is not in
so to send a signal to the control
panel
beeps twice
The accessory has already been
connected
one accessory to the control panel
No response from the
control panel following
commands from the
remote control
The remote control has not
been connected to the control
panel
manual to connect the remote
control to the panel
Remote control is too far from
the control panel
Transmission distance of the remote
A signal repeater can be installed to
increase the transmission distance
2322
Precauons
-
-
-
-
- The control panel is neither waterproof nor moisture-proof, install it in a shady, cool and dry
-
-
-
-
-
Standards
FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment .This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Table of contents
Popular Security System manuals by other brands
Johnson Controls
Johnson Controls Tyco PowerSeries Pro HS3032 user manual
Ecco
Ecco EB7260 Series Assembly, installation and operation instructions
Bosch
Bosch VSS7915/00T installation instructions
Lorex
Lorex LHB806 Quick connection guide
X10
X10 VT38A owner's manual
BigTimeClocks
BigTimeClocks BHD 109R-XL manual
