Maxlife MXBE-01 User manual
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Thank you for purchasing a product by Maxlife. Before use, please refer to the
User’s manual, and save it for future reference. Do not disassemble the device on
your own – all repairs should be done by a service technician. Use only original
parts and accessories provided by the manufacturer. The device should not be
exposed directly to water, moisture, sunlight, fire or other heat sources. We hope
that the product by Maxlife fulfills your expectations.
CHARGING THE CHARGING CASE
Before the first use, please put the earphones into charging case. Connect one
end of the USB cable to a USB-C port of the charging case. The other end should
be connected to a power adapter (or a USB port of your computer). Then plug the
power adapter into a power outlet.
Use only working charger with sufficient power.
Charging will be signaled by flashing the red LED on the charging case. Once fully
charged, the LED will stop flashing. When fully charged, disconnect the charging
case from the power source.
Note: A power adapter is not supplied with the earphones and should be
purchased separately!
CHARGING THE EARPHONES
With a built-in rechargeable battery, the charging case can provide charging
process up to 3 times for the earphones (both left and right). Please make sure
the earphones are fully charged before the first use.
Pay attention: In case you do not use the earphones for a long time, charge the
earphones at least once every 3 months.
EARPHONES PAIRING
The right (R) and left (L) earphones can work together (stereo mode).
Any earphone can work as an independent earphone (mono mode).
PROPER DISPOSAL OF USED EQUIPMENT
This device is marked with a crossed-out garbage container symbol, in
accordance with the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE). Products marked with
this symbol should not be disposed of or discarded with other
household waste at the end of their service life. The user is obliged to
dispose of waste electrical and electronic equipment by delivering it to a
designated point, where such hazardous waste is recycled. The collection of this
type of waste in separate locations and the proper recovery process contributes
to the conservation of natural resources. Proper recycling of waste electrical and
electronic equipment is benefcial to human health and environment. For
information on where and how to dispose of used electronic equipment in an
environmentally safe manner, the user should contact the relevant local
authority, the collection point or the point of sale where the equipment was
purchased.
PROPER DISPOSAL OF USED BATTERY
In accordance with EU Directive 2006/66/EC, as amended by
Directive 2013/56/EU on the disposal of batteries, this product is
marked with a crossed-out garbage container symbol. This symbol
means that the batteries used in this product should not be
disposed of with ordinary household waste, but handled in
accordance with the directive and local regulations. Do not dispose of batteries
with unsorted municipal waste. Battery users must use available collection
network for these items, that allows for their return, recycling and disposal.
Within the EU, the collection and recycling of batteries is governed by separate
procedures. To learn more about existing battery recycling procedures in your
The earphones would enter pairing mode automatically after taking out from
charging case.
1. Make sure the earphones and charging case are charged.
2. Activate Bluetooth connection on the device through which you want to
connect with the earphones.
3. Search for a new device. The earphones will be visible as “MXBE-01” on the list.
4. Connect with the earphones. Certain devices require entering code “0000”.
5. Correct connection of the earphones will be confirmed with a voice message.
“MXBE-01” will remember last paired device and attempt to connect with it
automatically after next power on.
Pay attention: If pairing device is switched off or Bluetooth is disabled, after 3
minutes the earphones will turn off automatically.
DEVICE OPERATION
After the connection you can control media and phone calls.
LED INDICATORS
LED indicator can help to understand what is going on with the earphones
Take the earphones out of the charging case or press long
multifunction button for 5 seconds, until earphones LED
indicator lights flash blue and red, and you hear a voice
prompt “Power on”.
Put the earphones into the charging case or (when not
paired) long press multifunction for 5 seconds until you
hear a voice prompt “Power off”. If you put only one earbud
into the charging case, the other earbud will continue
working.
Press the multifunction button twice.
Press the multifunction button on the right earphone
three times.
Play Next track
Press the multifunction button on the left earphone three
times.
Play Previous
track
Charging case battery is lower than
10%
The indicator on the charging case
blinks white
Charging case is charging
The indicator on the charging case
blinks red
The earphones are charging
The earphones are fully charged
The earphones indicator blinks blue
and red
The indicator on the earphones
is off
Earphones are in pairing mode
The indicator on the earphones is
solid red/The indicator on the
charging case is solid white
Charging case is fully charged
INDICATOR STATUS
The indicator on the charging case is
red
TelForceOne S.A. declares that the product is compatible with requirements
and other relevant provisions of the 2014/53/UE directive. You can download
the declarationon of product on website www.manual.maxlife.com.pl.
Designed in Poland | Made in China
TelForceOne S.A.
Krakowska 119
50-428 Wrocław / Poland
Telephone: (+48) 71 327 20 00
E-mail: info@telforceone.com
PRODUCER/CUSTOMER SERVICE OFFICE
MXBE01
BLUETOOTH TWS
EARPHONES
MANUAL
INSTRUKCJA OBSŁUGI
ENG
FUNCTION OPERATION
Power on
Power off
Play/Pause
Answer
phone call
Hang up
Reject phone
call
Voice
Assistant
Press the multifunction button twice.
Press the multifunction button twice.
Press and hold the multifunction button for 2 seconds.
Press and hold the multifunction button for 2 seconds.
area, contact your city hall, waste management agency or landfll.
The device and accessories are in line with the directives on
operational safety, health and environmental protection referred to
in the declaration of conformity. It is compatible with the provisions
of the New Approach Directives.
Separate collection of used products and packing allows materials to
be recycled and used again.
Table of contents
