Maytag MGC4430BD User instructions

Dimensions
"A" 28-1/2" (72.4 cm)
"B" 19-15/16" (50.6 cm)
"C" 2-1/8" (5.4 cm)
"D" 5-1/4" (13.3. cm)
"E" 29-1/2" (74.9 cm)
"F" 21" (53.3 cm)
"G" 3-13/16" (9.7 cm)
"H" 12-1/4" (31.1 cm)
30" (76.2 cm) and 36" (91.4 cm) Sealed Gas Cooktop
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10187822
08-07-08
Page 1 of 2
PRODUCT MODEL NUMBERS
MGC4430BD MGC4436BD
Gas supply: The installation of this appliance must
conform with local codes, or in the absence of local
codes, with the latest edition of the National Fuel Gas
Code ANSI Z223.1 USA or current CAN/CGA-B149
INSTALLATION CODE.
This appliance is designed to operate at a pressure of 5"
ofwater column (36" models), 4" of water column (30"
models) on natural gas or, if converted for use with LP
gas (propane or butane), 10 " water column. Make sure
this appliance is supplied with and adjusted for the type
of gas for which it is designed.
This appliance was adjusted at the factory for use with
natural gas. If, at any time, this appliance is to be used
with a different type of gas, all of the conversion
adjustments described in the installation instructions
must be made by a qualified service technician before
attempting to operate the cooktop on that gas. Natural
gas should be supplied to the appliance pressure
regulator at a line pressure between 6" – 14" of water
column or, if converted for LP gas, between 11"– 14".
All supply piping, except as noted, should use common
National Pipe Thread (N.P.T.). For all pipe connections
use an approved pipe joint compound resistant to the
action of LP gas.
The supply line must be equipped with a manual shutoff
valve. This valve should be located in the same room but
external to the range. It should be in a location that
allows ease of opening and closing.
Electrical: See page 2.
PRODUCT DIMENSIONS – 36" MODEL
PRODUCT DIMENSIONS – 30" MODEL
IMPORTANT: Cutout
dimensions are critical.
Dimensions must be
measured and cut
accurately to within
±1/16" (0.159 cm) to
ensure proper fit.
B
A
C
E
F
GH
Dimensions
"A" 34-1/2" (87.6 cm)
"B" 19-15/16" (50.6 cm)
"C" 2-1/8" (5.4 cm)
"D" 5-1/4" (13.3. cm)
"E" 36" (91.4 cm)
"F" 21" (53.3 cm)
"G" 3-13/16" (9.7 cm)
"H" 15-1/4" (38.7 cm)
B
A
E
C
F
GH
D
IMPORTANT: Cutout
dimensions are critical.
Dimensions must be
measured and cut
accurately to within
±1/16" (0.159 cm) to
ensure proper fit.

Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10187822
08-07-08
Page 2 of 2
PRODUCT MODEL NUMBERS ELECTRICAL WIRING DIAGRAM
MGC4430BD MGC4436BD
Gas supply: See page 1.
Electrical: This appliance is equipped with a grounded
type power cord. A grounded outlet must be provided. It
is recommended, for convenience, the outlet be located
within either the shaded area or the cross hatched area
shown at right.
User may experience occasional circuit tripping if Ground
Fault Circuit Interrupter (GFCI) outlet or breaker is in use.
In planning any installation, note that the free length of
this appliance’s power cord, extending beyond a point
3-3/4" (9.53 cm) left of the nominal center of the rear
wall of the burner box, when viewed from the front of the
unit, is approximately 46" (117 cm).
30" (76.2 cm) and 36" (91.4 cm) Sealed Gas Cooktop
CABINET OPENING DIMENSIONS
4ʺMAX.
10.16 cm
37 3/16 ʺ
94.46 cm
293/8ʺ
74.61 cm
3 13/16 ʺ
9.7 cm
CABINET BOTTOM
31/2ʺ(8.89 cm) WIDE
SLATS WHENAWALL
OVEN IS INSTALLED
BELOW 30ʺMODEL
Locate this appliance away from combustible materials such as
window curtains and combustible wall decorations.
Minimum horizontal clearance between the edge of the appliance
and combustible construction, extending from the cooking surface
to 18" (45.72 cm) above the cooking surface:
C=1.0" (2.54 cm) at rear
D=6" (15.24 cm) at sides
Dimensions apply to both 30" and 36" wide models.
A=30" (76.2 cm) minimum vertical clearance between
cooking surface and construction above the
appliance. This clearance may be reduced to not
less than 24" (60.96 cm) by protecting the underside
of the combustible material or metal cabinet above
the cooking surface with not less than 1/4" (0.635
cm) insulating millboard covered with sheet metal
not less than 0.0122" thick.
B=13" (33.02 cm) maximum depth of cabinets installed
above cooktop.
Avoid use of cabinets above cooktop for storage space
to eliminate associated potential hazards such as
reaching over open flames.
1.0ʺ
2.54 cm
18ʺ
45.72 cm
6ʺ
15.24 cm
1.0ʺ
2.54 cm
18ʺ
45.72 cm
6ʺ
15.24 cm
A
B
C
D