Maytag GAS RANGE User manual

PORTABLE
DISHWASHER
vens, Compactors, Room Air Conditioners, Dehumldlflers, Automatic Washers, Clothes Dryers, Freezers, Refrigerator-Freezers, Ice Makers,Dish\

INSTALLATION PROCEDURE
Before You Begin.. a
I. (‘aster Installation and
Removal of’ Materials From
Interior
Gstf;:s are supplied rn tile loose parts bag inside
the c!lsllwasher tub.
Lay tile dishwasher on its back using 2 corner posts
to prevent paint scratching. The corner posts should
be [)laced as shown in Figure 1
Remove tile bottom pad
Insert casters into mo:lntlng holes as shown in
Figure 2.
Stand the dishwasher upright and then remove the
I,acking rndterials, Customer Literature Package, and
faucet ;jcl;ll)ter kit from the dishwasher.
After ,llst,tllation has been coml)leted, discard the
~Jxkrnq rliaterlals. Piace tile Customer Literature
P,jckage and this InstallatYon Ir!struction on the top
of the dishwasher so th;lt they are readily available
to the customer.
2. Faucet Adapter Kit
Installation
Remove screen holder or aerator from faucet spout
if one is present. (See Figure 3.)

If ‘yo111.f;iiicet spout has vxxternal threads, screw the
,lti,lrltt:r iron1 [he Fauce! Adapter t<lt directly onto
ti?e l;iuci:t. If your fauce: spout has internal threads,
fir-st i:rst;!lI the threaded hushing and rubber washer
front thu iducet Adapter Kit onto the faucet. then
ii>st:;ll the adapter onto the tbushing as shown ~II
F I qu r&i ii
RUBBER WASHER
AND THREADED
BUSHING (FOR
FAUCETS WITH
INTERNAL
THREADS)
For other type faucets, see your dealer for special
type adapter kits.
NOTE: If dishwasher is attached to a faucet
equipped with a spray hose attachment,
walc’r pressure is applied to the spray hose.
To prevent possible failure, the spray hose
should be permanently disconnected or rep
placed with a good quality reinforced hose.
3. Electrical Requirements
A 120 Volt, 60 Hz, AC only, 15 Amp (20 Amp
171ilxir1ldl~~~
fused electrical supply is required.
(TII-ne rielay fuse is recommended.) It is recom
nlentle[l tt:,rt a separate circuit serving only this ap-
l)l~;~nce !~e provIdeO. DO NOT LISC an extension
coral Se[> Figure 5.
Electrical ground is required on this appliance.
Keconmended Grounding Method
DO NOT, UNDER ANY CIRCUMSTANCES,RE-
MOVE THE POWER SUPPLY CORD GROUND
PRONG.
For your personal safety, this appliance must be
grounded. This appliance is equipped with a power
supply cord having a 3-prong grounding plug. To
minimize possible shock hazard it must be plugged
into a mating 3-prong grounding type wall recep-
tacle, grounded in accordance with the National
Electrical Code and tocat codes and ordinances.
If a mating wall receptacle is not available, it is the
personal responsibility and obligation of the cus-
tomer to have a properly grounding 3-prong watt
receptacle installed by a qualified electrician. See
Figure 6.
m ~-~~%:ING TYPE
WALL RECEPTACLE
3-PRONG
GROUNDING
POWER SUPPLY
CORD

-1. Fmcet Conntdion
NOTE: Mininlurn ‘~.lax~rnurrl water pressure
r:: :dircjl?ierits are 15 PSI to 120 PSI.
0 T.lrn water off.
c. Use tiie ring til 111111hoses out of storage
cornpariment 011 /lack of dishwasher.
(;. AtLach the ties? connector to the faucet by
pulling down on the locking collar and lift
tny up on the connector until it snaps into
place on the faucet adapter. Release the
locking collar. See Figure 7.
e. Turn the hot water on slowly to the full open
position
After the dishes are washed:
a, Turn hot water OFF. (This may be done
during the dry cycle.)
b. Press the red button on the connector to
release water pressure. See Figure 8.
c. Grasp hose connector and lift up slightly.
d. Move the locking collar down and pull down
on the connector.
c. Empty any rem,jlning water from the con-
nector
f. Push hoses into storage cotnpartment.
~_--~- -__
PUSH COLLAR
AND SLIP FAUCET
CONNECTOR ONTO -4
THE FAUCET
ADAPTER
BUTTON
Operational Test
l Spin spray arm to check movement.
0 Start Dishwasher.
0 Check for leaks - particularly around door,
pump mounting gasket, and at hose connections.
0 Check water level -- water should just cover the
round heater element. .
0 Check for complete drain - no water should be
visible above grate when drain is complete.
If Dishwasher Won’t Run, or
Stops During Cycle.. .
Before Calling for Service,
Check These Points:
1. Is door tightly closed and latched securely?
2. Has cycle been correctly set to start dishwasher?
3. Is water turned on?
4. Is electric cord plugged In?
5. Has house fuse blown?
6. Has electrical power been interrupted?
7. If motor has stopped because of overload,
it will automatically reset itself within a few
minutes.
NOTE: To convert a front loading portable
dishwasher Into a built-in model, contact
your Whirlpool appliance dealer. Conversion
Kit No. 569056 is available through hirr to
facilitate the installation.
4

Instructions for Changing Color in Front
Panel Pack For Models SO Equipped
Remove Side Trim
NOTE: Either side trrn may be removed to
change color in the Front Panel Pack.
STEEP 1. Remove the tb’:o screlvs that fasten the
side trlrn to the door frarrle. See Figure 9.
STEEP 2. Open the door <Ibout half way, then slide
the trim downward until the upper edqe is free of
the console or end cap (about l/4”)
STEEP 3. Next lift off the <lde trinl.
Change Front Panel
STEP 4. Slide the panels sideways until they are
clear of the groove in the underside of the console
and the lower trim strip of the door. See Figure 9.
NOTE: There is a corrugated (cardboard)
spacer behind the panels that should be left
in place.
STEEP 5. Select the color VOLJ wash to have showing.
INSERT SIDE
TRIM BOTTOM
FIRST
Reinstall Panel Pack
and Side Rims
STEP 6. Position the panels so that upper edge of
the panels fits into the groove on the underside of
the console, and the lower edge of the panels fit
into the lower door trim. See Figure 9.
STEP 7. Slide the panels back into place, making
sure the cardboard spacer is in place in the door
assembly.
It may be necessary to gently push on the surface
of the panels so they will fit under the edge of the
side trim that is still in place. See Figure 10.
STEP 8. Slide the lower end (with cutout) of the
side trim downward until the upper edge will fit
under the lower edge of the console end cap. Next
slide the side trim upward until it is secure. See Fi-
gure 10. Make sure the panels are in place before
installing the side trim.
STEP 9. Posrtron the side trim so the two moun
ting holes in the side trim align with mounting
holes in the door frame.
STEP 10. Install the two mounting screws in the
side trim.
5

Part No. 303312 Rev. A
Maktng your world a little easier
IP rhe euenr your WHIRLPOOL appliance should need service. call rhe dealer from whom you purchased
rhe appliance or a WHIRLPOOL franchtsed TECH~CARE L service company. He 15 ,n rhe Yellow Pages of your
Telephone d~recrory listed under “Appliances Household~Ma]or~Servlce and Repair.” You can also obtain his
name and number by dlallng, free, wirhln the contlnenral Unlred States rhe Whfrlpool COOL LINE& Service
(8001 253 1301 When calling from Mtchlgan, dial 1800) 632.2243. from Alaska or Hawail, dfal (8001 253 1121.
Dual 1~s~ as you normally dial long distance A special operafor will fell you rhe name and number of your
nearesf Whirlpool TECH CARt st?rwce outlet During normal workfng hours. WhIrlpool tonsul~ants ar
rhls same number WIII also answe’ any questions about operaring or mainralmng your appliance GOT covered
in your Use and Care Gutde
PrInted in U.S.A.
s, Automatic Kashers, Clothes Dryers, Freezers, Refrigerator-Freezers, Ice Makers, Dishwashers, Built-In Ovens and Surface Units, Ranges, Microl’