Maytag 27-inch electric built-in single cavity wall... User manual

Z_OEdwardsStreet,SE
Cleveland,Tennessee37311
fei:423-472_33_3
F3x:423-478-6710
INSTALLATIONINSTRUCTIONS
27-INCH ELECTRIC
BUILT-IN SINGLE CAVITY WALL OVEN
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE
WIRING
The neutral of this unit is grounded to theframe through the _en grounding wire,(The green and the white
wire are twistedtogether at the termination ofthe conduit). If local conditions doe not permit _ounding ofthe
neutral, untwist the green wire and connect the green wire to ground in accordance with local codes. Connect
the white neutral to the service neutral.
PROPER ELECTRIC SUPPLY
You must provide an adequate electrical supply outletas requiredfor youroven.Checkwithlocal utility for
governing electrical codes andordinances. In the absence of lncalelectrical codes, the National Electric Code,
NFPA No. 70, governingelectric range installations must be followed. A copy of the National Electrical
Code, NFPA No. 70, can be obtained by writing to:
National Fire ProtectionAssociation
Batterymarch Park
Quincy, MA 02269
Athree-wire, singlephase, AC120/240 volt or 120/208 volt, 60 Hz electrical system (properly fused tomeet
NFPA No.70) must be provided. The ovencircuit should be fused with a 30 ampere fuse if it istheonly unit
on the circuit. Size No. 10 wire (minimum)may beused if the ovenis the only appliance onthe circuit. If
smaller sizes ofwire are used,the unit efficiency will be reduced and a fire hazard may be created.
It isadvisable that the electrical wiring and hookup be accomplished bya competent electrician.
Make electrical connectionswith a 120/240 volts or I20/208volt, 60 Hz, single-phase, AC three-wire electri-
cal system. All wire connections must be in accordance with local codes and properly i_ulated. Be sure to
check local codes for wire size and installationrequirements. Unitmust be properly grounded in accordance
with local wiring code.
SERVICE
Interrupt the source of elect_cityto the unit be disconnecting the fuse or eircu#breaker when attempting to
repair or service the oven.Failure to do this could result in a dangerous or even fatal shock.
SPECIFICATIONS
Voltage 120/240 Volts AC 120/208Volts AC
Amperage 24.2 Amps 21. I Amps
Watts 5700 4300
Frequency 60 Hz
Weight 142 lbs.

2_0EdwardsStta.=t.SE
Clove)ant1,Tennessee37Sli
Tel -'Z2-47Z-3233
Fax:47_2-473-6710
1.CAUTION: Some 27-Inch built-in cabinets may not bewide enough,due to their construction to allow
this installation.
2.Cut hole incabinet tomount oven. Cut out in cabinet should beleveland straight. NOTE: Themare no
provisions tolevel the unit after itis installed.An oventhat is notlevel will causepoor bakingresults.
3.Installplywood floor perfollowing instructions.
4.Assembleunit to the cabinetwiththe fourNo, 8 x1" screws supplied with unitinside of envelope contain-
ingthese instructions.Pra-dril! holesin cabinetfor attachmentscrews using 1/8" drill, Oven mounting boles
are in eachcornerof front panel.
5.See previous pagefor electricalhook-up.
6.See User's Manual for operating instructionsandwarranty.
7.Packed with this unitis an additional bottom trim to cover thebottom edge of the cabinet cutout, If
needed, loosenthe screws ontheunderside of the frontclosure and slip trim in place withthe solidflanged
sidedown. Retighten screws.
TRIM J_
CAtqN_r
j•
27"24"CAUTION: If cabinetdoorsareprovided above
wall oven,aminimum spacing of3_',t"is required
rain._ rain.forV=" thick doors.Forthicker doors,increasethe
Y 1"for each%"additional thickness.
CAUTION: Oven vent.
0o not locatedo notobstruct.
junction box,'--_2g-3/8"
in shaded area. |
Provide clearancek,,'ETypical corner
ho(e forconduit"" " ".,_j 4" to screw.
accessto junction"33"#8 x 1 screw.
box below ply-(-
wood floor. I floor
]28-1/8"
ConstructSie" r, n.'_ .._
plywoodfloor flush \
withbottom of open-
ing. Floor mustbe
cagabie ofsupporting 23.,NOTE: Donotb)ock air
142 Ibs._ intakeslotsalong sides
/and bottom of unit.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'SUSE.