Maytag PerformaHJ6301JRT2 User manual

1VL AG
ELECTRIC
WATER HEATER
USER'SGUIDE Model Numbers
HJ6301J_2 HJ6302JRT2
HJ6301JLS HJ6302JLS
HJ6401JRT2 HJ6402J_2
HJ6401JRT2F HJ6402J_2F
HJ6401JRS HJ6402JRS
HJ6401JLS HJ6402JLS
HJ6521J_2 HJ6522J_2
HJ6521JRT2F HJ6522JRT2F
HJ6521JRS HJ6522JRS
HJ6501JLSW HJ6502JLSW
HJ6661JRT HJ6662J_
HJ6821JRT HJ6822J_
HJ61201JRT HJ61202JRT
®FOR POTABLE WATER
•IsTEo HEATING ONLY
GAMA certification applies to all residential
e_ectricwater heaterswithcapacitiesof 20 to NOT SUITABLE FOR
120 Gallons.Input rating of 12 Kw or lessat a SPACE HEATING
voltage no greater than 250V.
Caution:
AWARNING I Read and Follow All
READTHE GENERALSAFETYSECTIONBEGINNINGON INSIDEI Safety Rules and
COVERANDTHENTHISENTIREMANUALBEFOREINSTALLINGOR Operating Instructions
OPERATINGTHISWATERHEATER. Before First Use of
Save this Manual for FutureReference.This Product.

Safety Instructions
AWARNING AWARNING
Improper installation, adjustment, alteration, service At the time of manufacture this water heater was pro-
or maintenance can cause DEATH, SERIOUS BODILY vided with a combinationtemperature-pressuresrelief
INJURY,OR PROPERTYDAMAGE. Refer to this manu- valve certified by a nationally recognized testing labo-
al for assistance consult your local utility or call ratory that maintains periodic inspection of production
Maytag Customer Service at 1-800-788-8899 for an of listed equipment or materials, as meeting the
authorized servicer for further information, requirements for Relief Valves and Automatic Gas
Shutoff Devices for HotWater Supply Systems, and
the latest edition of ANSI Z21.22 and the code require-
ments of ASME.If replaced,the valve must meet the
A, WARNING mquiremeuts of local cedes,but not lessthan a combi-
nation temperature and pressure relief valve certified
HAZARDOF ELECTRICAL SHOCK!Before removing as meeting the requirements for Relief Valves and
any access panels or servicing the water heater,Automatic Gas Shutoff Devices for Hot Water Supply
make sure the electrical supply to the water heater Systems,ANSI 7.21.22 bya nationally recognized test-
is turned "OFF". Failure to do this could result in ing laboratory that maintains periodic inspection of
DEATH,SERIOUS BODILY INJURY,OR PROPERTY production of listad equipment or materials.
DAMAGE. The valve must be marked with a maximum set pres-
sure not to exceed the marked hydrostatic working
pressure of the water heater (150Ibs./sq.in.) and a
discharge capacity not less than the water heater
input rate as shown on the model rating plate.
A'WARNING (Electric heaters - watts divided by 1000 x 3415 equal
HOTTER WATER CAN SCALD: Water heaters are BTU/Hr. rate.)
intended to produce hot water. Water heated to a Your local jurisdictional authority, whilemandating the
temperature which will satisfy clothes washing, useof a temperature-pressure relief valve complying
dish washing, and other sanitizing needs can scald with ANSI Z21.22 and ASME, may require a valve model
different from the one fum shed with the water heater.
and permanently injure you upon contact. Some
people are more likely to be permanently injured by Compliance with such local requirements must be sat-
hot water than others.These include the elderly,isfied by the installer or end user of the water heater
children,the infirm,or physically/mentally handi-with a locally prescribed temperature-pressure relief
capped. If anyone using hot water in your home fits valve installed In the designated opening in thewater
into one of these groups or if there is a local code or heater in place of the factory furnished valve.
state law requiring a certain temperature water at Forsafe operation of the water heater, the relief valve
must not be removed from it's designated opening or
the hot water tap, then you must take special pre-
cautions. In addition to using thelowest possible plugged.
temperature setting that satisfies your hot water The temperature-pressure relief valve must be
needs, a means such as a mixing valve, should be installed directly into the fitting of the water heater
used at the hot water taps used by these people or designated for the relief valve. Position the valve
at the water heater. Mixing valves are available at downward and provide tubing so that any discharge
plumbing supply or hardware stores. Follow manu- will exit only within 6 inchesabove,or at any distance
tacturers instructions for installation of thevalves, below thestructural floor. Becertain that no contact is
Before changing the factory setting on thethermo- made with any live electrical part. The discharge open-
stat, read the "Temperature Regulation"section in ing must not be blocked or reduced in size under any
this manual, circumstances. Excessivelength, over 30 feet, or use of
more than four elbows can cause restriction and
reduce the discharge capacity of the valve.
No valve or other obstructionisto be placed between
the relief valve and thetank. Do not connect tubing
AWARNING directly to discharge drain unlessa 6"air gap is provid-
INSULATING JACKETS: When installing an external ed. To prevent bodily injury, hazard to life, or property
water heater insulation jacket on an electric water damage, the relief valve must be allowed to discharge
heater: water in quantities should circumstances demand. If
• DONOT cover the temperature-pressure relief valve, the discharge pipe isnot connected to a drain or other
•DO NOT put insulation over the access covers or suitable means, thewater flow may cause property
any accessareas, damage.
•DO NOT cover or remove operating instructions, The Discharge Pipe:
and safety related warning labels and materials Must not be smaller in size than theoutlet pipesize
affixed to the water heater, of the valve, or have any reducing couplingsor
other restrictions.
Must not be plugged or blocked.
Must be of material listed for hot water distribution.
•,WARNING Must be installed so as to allow complete drainage
of both the temperature-pressure relief valve, and
Do not usethis appliance if any part of it has been the discharge pipe.
under water. An electrical short or malfunction could Must terminate atan adequatedrain.
occur. The water heater shou d be rep aced. Must not have any valve between the relief valve
and tank.
2

Safety Instructions (cont'd)
WATER _WARNING
HEATERS EQUIPPED FORONE VOLTAGE
ONLY: This water heater is equipped for one type
voltage only. Check the rating platenear the bot-
tom access panel for the correct voltage. DONOT
use this water heater with any voltage other than
the one shown on the model rating plate. Failure to
use the correct voltage can cause problems which
can result in DEATH,SERIOUS BODILY INJURY, OR
PROPERTY DAMAGE. If you have any questions or
doubts consult your electric company.
ACAUTION
WATER HEATERS EVENTUALLY LEAK: Installation of l
the water heater must be accomplished in such a I
manner that if thetank or any connections should I
leak, the flow of water will not cause damageto the
structure.For this reason, it isnot advisable to insta
the water heater in an attic or upper floor. When
such locations cannot be avoided, a suitabledrain
pan should be installed under the water heater.
Drain pans are available atyour local hardware
store. Such a drain pan must have a minimum diam-
eter of at least 13/, inches greater than the water
heater diameter and must be piped to an adequate
drain. Under no circumstances isthe manufacturer or
Maytag to be held liable for any water damage in
connection with this water heater.
I

Table of Contents
Safety Instructions .....................................................................................................................................2-3
Table of Contents ...........................................................................................................................................4
Customer Information ............................................................................................................................s
Product Specifications ..........................................................................................................................s-7
Accessories and Tools Needed ....................................................................................................8
Accessories ............................................................................................................................................................................ 8
Tools ..................................................................................................................................................................................... 8
Instructions for Installation ........................................................................................................ 9-15
Removing the Old Water Heater .......................................................................................................................................... 9
Locating the New Water Heater ......................................................................................................................................... 10
Typical Installation .............................................................................................................................................................. 10
Water Piping ....................................................................................................................................................................... 11
Temperature-Pressure Relief Valve ..................................................................................................................................... 12
Filling the Water Heater ..................................................................................................................................................... 13
Wiring Diagrams ................................................................................................................................................................ 13
Wiring ................................................................................................................................................................................ 14
Installation Checklist .......................................................................................................................................................... 15
Service and Maintenance ............................................................................................................ 16-21
Temperature Regulation ...................................................................................................................................................... 16
Thermostats ........................................................................................................................................................................ 16
Temperature Settings .......................................................................................................................................................... 16
Thermostat Adjustments .................................................................................................................................................... 17
Temperature-Pressure Relief Valve Operation .................................................................................................................... 17
Draining .............................................................................................................................................................................. 18
Thermostat Removal ...................................................................................................................................................... 18,19
Element Cleaning and Replacement ............................................................................................................................. 19-21
Drain Valve Washer Replacement ...................................................................................................................................... 21
Service ................................................................................................................................................................................. 21
Troubleshooting ......................................................................................................................................22-24
Start Up Conditions ............................................................................................................................................................ 22
Thermal Expansion ........................................................................................................................................................ 22
Strange Sounds ............................................................................................................................................................... 22
Operational Conditions ................................................................................................................................................. 22,23
Smelly Water .................................................................................................................................................................. 22
Air in Hot Water Faucets ............................................................................................................................................... 22
Rumbling Noise ............................................................................................................................................................. 22
High Temperature Shut Off System ......................................................................................................................... 22,23
Not Enough Hot Water ................................................................................................................................................. 23
Water is Too Hot ........................................................................................................................................................... 23
Leakage Checkpoints ..................................................................................................................................................... 24
Repair Parts List .......................................................................................................................................26-34
Warranty ....................................................................................................................................................................36
4

Customer Information
Thank Youfor purchasinga Maytagwaterheater. •The installation must conformwith the instructions in this
Properly installedandmaintained, it should give you years of manual; electric company rules;andLocal Codes, or in the
absence of LocalCodes, with the latest edition of the
trouble free service. It is strongly suggestedthat this new
waterheater be professionally installed, call MaytagCustomerNational Electrical Code. This publication is available from
Service at 1-800-788-8899for recommended installers, your local government or public library or electric company
or by writing Underwriters Laboratories Inc., 333 Pfingsten
Abbreviations Found In This Instruction Manual Road, Northbrook, IL 60062.
U.L.-Underwriters Laboratories Inc., 333 Ptingsten Rd., •If after readingthis manual you have any questions ordo
Northbrook, IL60062 not understandany portion of the instructions, call Maytag
National Electrical Code-This pubhcation isava//able from Customer Service at 1-800-788-8899 for an authorized
your local government or public library or electric company or servicer.
by writing to U.L. above.
ANSI-American National Standards Institute •Carefi_lly plan the place where you are going to put the
water heater. Correct electrical wiring and connections are
•Read the "Safety Instructions"section, pages 2 and 3 of this very important in preventing death from possible electrical
manual first and then the entire manual carefully. If you shock and tires.
don't follow the safety rules, the water heater will not oper- Examine the location to ensure the water heater complies
ate properly. It could cause DEATH, SERIOUS BODILY with the "Locating the New Water Heater" section.
INJURY AND/OR PROPERTY DAMAGE.
This manual contains instructions for the installation, oper- • ForCalifornia installation this water heater must be braced,
ation, and maintenance of this electric water heater. It also anchored, or strapped to avoid falling or moving during an
contains warnings throughout the manual that you must earthquake. See instructions for correct installation proce-
read and be aware of. All warnings and all instructions are dures. Instructions may be obtained from the California
essential to the proper operation of the water heater and office of the State Architect, 400 P Street, Sacramento, CA
your safety. Since we cannot put everything on the first few 95814.
pages, READ THIS ENTIRE MANUAL BEFORE
ATTEMPTING TO INSTALL OR OPERATE THE •Massachusetts Code requires this water heater to be
installed in accordance with Massachusetts 248-CMR 2.00:
WATER HEATER. State Plumbing Code and 248-CMR 5.00.
Product Specifications
Model HJ6301JRT2 HJ6302JRT2 HJ6301JLS HJ6302JLSHJ6401JRT2
HJ6401JRT2F
TankCapacity
In Gal.30303030 40
•ElementUpper -- 4500 -- 4500 --
Wattage
at 240 VoltLower4500 4500 4500 4500 4500
Recovery Rate Upper -- 20 -- 20 --
In Gals Per Hr.
@90*F Rise Lower 2020202020
Diameter 18"18" 22" 22" 18"
Height 46"46"293/," 293/4" 591/2"
Maximum Fuse or
Circuit Breaker Size 303030 30 30
Minimum
Wire Size (Gauge)10 10 10 10 10
• Standarddement wattagesareshown.Other elementwattages (up tothe maximum shown) areavailablewhen specified.
•Wiringsize basedon standard60"Ccopperwire.If distancefrom fuse boxtowaterheateris more than 90 feet, refertoyour
localelectricalcode.
5

Product Specifications
Model HJ6402JRT2 HJ6401JRSHJ6402JRS HJ6401JLSHJ6402JLS
HJ6402JRT2F
Tank Capacity
In Gal. 40 40 404040
*ElementUpper 4500 -- 4500-- 4500
Wattage
at 240 VoltLower4500 4500 4500 4500 4500
Recovery Rate Upper 20 -- 20 -- 20
In Gals. Per Hr.
@90°F Rise Lower 202020 20 20
Diameter 18"20"20"24" 24"
Height59112"47" 47"311/2" 31%"
Maximum Fuse or
Circuit Breaker Size 30 30 30 3030
Minimum
Wire Size (Gauge) 10 10 10 10 10
Model HJ6521JRT2 HJ6522JRT2 HJ6521JRSHJ6522JRSHJ6501JLSW
HJ6521JRT2F HJ6522JRT2F
TankCapacity
In Gal.50 50 50 5050
*Element Upper-- 4500 -- 4500--
Wattage
at 240 Volt Lower4500 4500 4500 4500 4500
RecoveryRate Upper -- 20-- 20 --
In Gals. Per Hr.
@ 90*F Rise Lower 20 20 20 20 20
Diameter 20"20"23"23"25"
Height 58"58"46%"46%"31%"
Maximum Fuseor
Circuit Breaker Size 303030 30 30
Minimum
Wire Size (Gauge) 10 10 10 10 10
Model HJ6502JLSW HJ6661JRTHJ6662JRT HJ6821JRT HJ6822JRT
TankCapacity
In Gal.50 66 66 80 80
*ElementUpper 4500 -- 4500 -- 4500
Wa
Vatta_
at 240ColtLower4500 4500 4500 4500 4500
RecoveryRate Upper 20-- 20 -- 20
In Gals.Per Hr.
@ 90*F Rise Lower 2020 20 20 20
Diameter 25" 22"22"24"24"
Height 313/,"60%"60%"60%"60%"
Maximum Fuse or
Circuit BreakerSize 30 30 30 30 30
Minimum
Wire Size (Gauge)10 10 10 10 10
*Standard element wattages are shown.Other element wartages(up to the maximum shown) are availablewhen specified.
*Wiring size basedon standard 60°C copper wire. If distance from fusebox to water heater ismore than 90 feet, referto your
localelectricalcode. 6

Product Specifications
Model HJ61201JRT HJ61202JRT
Tank Capacity
In Gal.119119
*Element Upper -- 4500
Wa
va_
at240 _olt Lower 4500 4500
Recovery Rate Upper -- 20
In Gals. Per Hr.
@90°FRise Lower 2020
Diameter 28"28"
Height 641//' 641/4"
Maximum Fuse or
Circuit Breaker Size 3030
Minimum
WireSize (Gauge) 10 10
*Standard element wattages are shown.Otherelementwattages(up to the maximum shown) are availablewhen specified.
*Wiringsizebased on standard 60°Ccopperwire. If distance from f_se boxto waterheater is more than 90 feet, referto your
localelectricalcode.
7

Accessoriesand Tools Needed
Accessories
To simplify the installation Maytag hasavailable the installa-
tion parts shown below. You may or may not need allof these
accessories depending on your type ofinstaUation. Call
Maytag Custdmer Service at 1-800-788-8899 for an autho-
rized installer.
C5
DRAIN PANSAVAILABLEIN 22"DIAMETER(PART
EXPANSIONTANKSFORTHERMALEXPANSION NUMBER66001011) FORWATERHEATERSHAVING
CONDITIONSAVAILABLEIN 2 GALLON(PART A DIAMETER20"ORLESS,24"DIAMETER(PART
NUMBER66001013) AND SGALLON(PART NUMBER66001105) FORWATERHEATERSHAVING
NUMBER66001014) CAPACITY A DIAMETER22"OR LESSAND AVAILABLEIN 28"
DIAMETER(PARTNUMBER66001012) FORWATER
HEATERSHAVINGA DIAMETER26.25"ORLESS
Tools ADDITIONAL TOOLS NEEDED
WHEN SWEAT SOLDERING
You may or may not need all of these tools, depending on your
tyj3e of installation. These tools can be purchased atyourlocal • Tubing Cutters or Hacksaw
Xlaytag store. • Propane Torch
•Soft Solder
•Pipe Wrenches (2) 14" • Solder Flux
•Screwdriver •Emery Cloth
•6 Foot Tape of Folding Rule *Wire Brushes
•Garden Hose
•Drill
•Pipedope or Teflon Tape
6 FOOTTAPE
GARDENHOSE3/4"WIREBRUSH
SLOT-HEADSCREWDRIVER PIPE
-WRENCH 1/2"WIREBRUSH
PHILLIPSSCREWDRIVER _ _ PROPANETORCH
ROLLOF LEADFREE
PIPEDOPE _SOFTSOLDER(SQUEEZETUBE,
ROLLOFTEFLONTAPE DRILL ROLLOFEMERY SOLDERFLUX TUBINGCUTTER
(Useonly on water connec- CLOTH
tions) 8

Installation Instructions
Removing the Old Water Heater
Turn supply to water@a. If you have copper piping to the water heater,the two
"OFF" electrical the heater.
copper water pipes can be cut with a hacksaw approxi-
@_ _ mately four inches away from where they connect to
the water heater. This will avoid cutting off the pipes
too short. Additional cuts can be made later if neces-
sary. Disconnect the temperature-pressure rebel valve
drain fine. When the water heater is drained, discon-
nect the hose from the drain valve. Close the drain
valve. The water heater is now completely disconnect-
ed and readyto be removed.
Turn "OFF" the water supply to the
water heater at the water shutoff valve _ [
or water mete_
Attach a to the water heater
hose drain
valve and put the other end in a floor 1_----- ]1 5_)b. If you have galvanized pipe to the water
drain oroutdoors. Open the water_] heater, loosen the two galvanized pipes
heaterdrain valve.Open a nearby hotwith a pipe wrench atthe union in each
waterfaucet which will relieve pressure line. Also disconnect the piping remain-
in the waterheaterand speed draining,ing to the water heater. These pieces
should be saved since theymaybe needed
__ _ when reconnecting the new water heater.
Disconnect the temperature-pressure
relief valve discharge pipe. When the
water heater is drained,disconnect the
hose from the drain valve. Close the drain
valve. The water heater is now completely
1[- -[1 disconnected and ready to be removed.
The water _,WARNlNGpassingout of theelectricaldrain __1[l_is _
valve may be extremely hot, To
avoid being scalded, make sure all
connections are tight and that the
water flow is directed away from
any person.
Check again to make sure the supply turned
-- "OFF" to the water heater. Then disconnect the electri-
cal supply connection from the water heater junction
box.
_itl _CAUTION
Mineral buildup or sediment may have accumulated I
._:_ _,_. in the old water heater. This causes the water
heater to be much heavier than normal and this
residue,f spi ed out, could cause staining.
9

Instructions for Installation (cont'd)
Locating The New Water _,CAUTION ]
Heater WATER HEATERS EVENTUALLY LEAK: Installation of/
the water heater must be accomplished in such a_
You should carefully choosean indoor location for the new manner that if the tank or any connections should |
waterheater, becausethe placement is a very important con- leak, the flow of water will not cause damage to the
structure. For this reason, it is not advisable to instal
slderation for the safety of the occupants in the building and the water heater in an attic or upper floor. When
for the mosteconomical use of the appliance. This water such locations cannot be avoided,a suitable drain
heater isnot intendedfor outdoor installation, pan should be installed under thewater heater.
Drain pans are available at your local hardware
store. Such a drain pan must havea minimum diam-
Whether replacing an old water heater or putting the water eter of at least 1314inches greater than the water
heater in a new location, the following critical points must be heater diameter and must be piped to anadequate
observed, drain. Under no circumstancesisthemanufacturer or
Maytag to beheld liable for any water damage in
connection with this water heater.
1. The location selected should be indoors as close to and as
centralized with the water piping system as possible. This r1
water heater, as well as all water heaters, will eventually [_kCAUTION]
leak Do not instal/without adequate drainage provisions I INSTALLATION IN RESIDENTIAL GARAGES; The water /
I /
|heater must be located and/or protected so it is not/
where water flow will causedamage. [ subject to physical damage by a moving vehicle. J
2. The location selection must provide adequate clearances for
servicing and proper operation of the water heater.
Typical Installation VACUUMREL,EFREQU,REDSOMECODES
,REFERTO'O LCOOES,
CHECK ALL CONNECTIONS FOR LEAKS. IAHOTWATER,W=TATER _
CONSULT THE LOCAL UTILITY COMPANY TOEXAM-OUTLET COLDWATERINLET
INE INSTALLATION FOR PROPRIETY AND SAFETY. _O_ kk._=_
*AWARNING 1ELBOW
HOTTER WATER CAN SCALD: Water heaters are/1 UNION UNION
intended to produce hotwater, Water heated to a/
temperature which will satisfy clothes washing,[ _ READED
dish washing, and other sanitizing needs can scald I TEM- _,_ J __ C'C)NI_'I_t_ORS
and permanently injure you upon contact. SomeI PERED"_w _
people aremore likely to bepermanently injured by WATER *MIXINGVALVE
hot water than others. These includethe elderly,OUTLET _[_
children, the infirm, or physically/mentally handi- • •
capped. If anyone using hot water in your home fits JUNCTIoNELECTRICALBoxIi Ii _1r E-_TEMPERATURE-
into one of these groups or if there isa local code or k=_==JI I PRESSURE
ACCESSCOVER I IRELIEFVALVE
state law requiring a certain temperature water at
the hot water tap, then you must take special pre-
cautions. In addition to using the lowest possible
temperature settingthat satisfies your hot water DISCHARGE
needs, a means such as a mixing valve, should be IF PIPE
used at the hot water taps used by these people or _(Donotcap
at the water heater. Mixing valves are available at or plug)
plumbing supply or hardware stores.Follow manu-
facturers instructions for installation of the valves. ACCESSCOV /DRAIN VALVE
Before changing the factory setting on the thermo- _/
stat, read the"Temperature Regulation"section in
this manual, if'AIR GAP
TOSUITABLEDRAIN
10

Instructions for Installation (cont'd)
Water Piping
AWARNING NOTE: Your water heater is super insulated to minimize
HOTTER WATER CAN SCALD: Water heaters are heat loss from the tank. Furtherreduction in heat loss can
intended to produce hot water. Water heated to a be accomplished byinsulating the hot waterlines from the
temperature which will satisfy clothes washing, waterhearer.
dish washing,and other sanitizing needs can scald
_nd permanently injureyou upon contact. Some
_eople aremorelikely to bepermanently injured by
lot water than others. These include the elderly,
children,the infirm,or physically/mentally handi-
capped. If anyone using hot water in your home fits
into one of thesegroups or if there is a local code or
state law requiring a certain temperature water at HOTOUTLETTO SHUT-OFF COLDINLET
the hot water tap,then you must take special pre- HOUSE VALVE_WATERLINE
cautions. In addition to using the lowest possible < [1_ '_
temperature settingthat satisfies your hotwater _-"_/_ % _ _X N
needs, a means such as a mixing valve, should be
used at the hot water taps used by these people or THREADED Td_1
at the water heater. Mixing valves are available at THREADEDTO
plumbing supply or hardware stores. Follow manu- SWEATCOUPLING _ _SWEATCOUPLING
facturers instructions for installation of the valves.
Before changing the factory setting on the thermo-
stat,read the "Temperature Regulation"section in _ .......
3/4"THREADED-- -- 3/4"THREADED
this manual. NIPPLE _'¢11_- NIPPLE
_HOT COLD,<
The illustration shows the attachment of the water piping to _ c::,_
the water heater. The water heater is equipped with 3/4inch i--==--3TEMPERATURE-
PRESSURERELIEF
water connections. U _ VALVE
If a water heater is installed in a closed water supply system;
such as one having a back-flow preventer,check valve,water
meter with a check valve, etc.in the cold water supply; DISCHARGEPIPE
means shall be provided to control thermal expansion. IDonotcapor plug)
Contact the local utility or call Maytag Customer Service at
1-800 788-8899 for an authorized servicer on how to con-
trol this situation. r'"l II
NOTE:If using coppertubing, soldertubing toan adapter_--_ U -----F
before attachingthe adaptor tothe cold water inlet connection. L._,=J T6
Do notsolderthe cold watersupply line directly tothe cold _x.. _%_" AtRGAP
water inlet. It will harm the diptube and damage thetank.
NOTE:To protect against untimely corrosionof hot andcold FLOORDRAIN
waterfittings, it is strongly recommendedthat di-electric
unions or couplingsbe installed on this waterheater when con-
nectedtocopperpipe.
1. Look at thetop cover of the water heater. The water outlet
is marked hot.Connect the hotwater pipetothehotwater
outlet of the water heater.
2. Look at thetop cover of the water heater. The cold water
inlet is marked cold. Connect the cold water pipetothe
cold water inlet of the water heater.
11

Instructions for Installation (cont'd)
Temperature-Pressure Relief Valve
A, WARNING I _, WARNING
At the timeof manufacturethis water heater was provid- The temperature-pressure relief valvemust be manu-
ed with a combinationtemperature-pressuresrelief valve I ally operated at least once a year. Caution should be
taken to ensure that (1) no one is in front of or
certified by a nationally recognizedtesting laboratory that I
maintains periodic inspection of production of listed I around the outlet of thetemperature-pressure relief
equipment or materials, as meeting the requirements for valve discharge line, and (2) the water manually dis-
Relief Valvesand Automatic Gas Shutoff Devicesfor Hot charged will not causeany bodily injury or property
Water Supply Systems, and thelatest edition of ANSI damage because the water may be extremely hot.
Z21.22 and the code requirements of ASME. If replaced,If after manually operating the valve, it fails to com-
the valve must meet the requirementsof localcodes,but pletely reset and continues to release water, immedi-
not lessthan a combination temperatureand pressure ately close thecold water inlet to the water heater,
relief valve certified as meeting the requirements for follow the draining instructions, and replace the
Relief Valvesand Automatic Gas Shutoff Devicesfor Hot temperature-pressure relief valve with a new one.
Water Supply Systems,ANSI Z21.22 by a nationally recog- I
nized testing laboratory that maintainsperiodicinspection!
of productionof listedequipmentor materials. ! _ _11 t, C(OLD
The valve must be marked with a maximum set pressure
not to exceedthe marked hydrostaticworking pressureof
the water heater (150 Ibs./sq.in.) and a dischargecapacity
notlessthan the water heater input rate asshown on the
model rating plate. (Electricheaters -watts divided by L1000x 3415equal BTU/Hr.rate.)
Your local jurisdictional authority, while mandating the
useof a temperature-pressurerelief valve complyingwith CONDUIT
ANSIZ21.22 and ASME,may require a valve model differ-TEMPERATURE-
ent from the one furnishedwith the water heater. _PRESSURE
Compliancewith suchlocalrequirements mustbesatisfied RELIEFVALVE
by theinstaller or end user of the water heater with a
Iocallyprescribed temperature-pressurerelief valve _-DISCHARGEPIPE
installedin the designatedopening in the water heater in _(Donotcapor plug)
placeof the factory furnishedvalve.
Forsafe operation of the water heater, therelief valve
must notberemoved from it's designated opening or
plugged.
The temperature-pressurerelief valve must be installed
directly intothe fitting of the water heater designatedfor
the relief valve. Positionthe valve downward and provide
tubing sothat any dischargewill exit only within 6 inches
above, or at any distancebelow thestructural floor. Be
certain that no contact is made with any live electrical _-_
part. Thedischarge opening must not be blocked or m6"AIRGAP
reducedin sizeunder any circumstances.Excessivelength, _-
over 30 feet, or useof more than four elbows cancause FLOORDRAIN V
restrictionand reducethe dischargecapacityof the valve.
No valve or other obstructionisto be placedbetween the 1NARNING "RELIEF VALVE OPENING"
N _eq _ Re_v_w4_dAu_n_c_ Shu_eDoves_H_W_S_/SyCe_An_1.22
relief valveand the tank.Do not connecttubing directly to _lis waterheater_pr0v_eqw_ a _ Te,_0etat0_RdiefV_ve Istedasco " w_
dischargedrain unlessa 6 air gap isprovided.Toprevent _,o0_q_ofAS,E
_AI_ANS_1,_ andASME,m_requ_ea valvemodal_ifemntfromIhe one_umish_d_ _ _ _.bodily injury, hazard to life,or property damage,the relief_,_ _o_,_,_m,_u,u_of aTe_,*P_umP_V_
valvemust be allowed to dischargewater in quantities _._._._mu=_,_._of_._.._
_pre,_db_Temperllture-P_e_ureReliefValve install_inthedes_gn_ed_ening in_.e water
should circumstances demand. If the discharge pipe isnot
_J_RCoA_SpE_LINGTANK;_'_'_,_,!:JACKET
connected to a drain or other suitable means, the water ,_:,-, BRASS
TAT-NFKG COUPLING
flow may cause property damage. _.,.Z_l,_rF;_rlz_r-_.1% _
The DischargePipe: T&PREUEF
VALVEPROBE _ _IEMPERATURE-
MUST EXTEND PRESSURE
•Must notbe smaller in sizethan the outlet pipesize ofINTO TANK RELIEFVALVE
the valve, or have any reducing couplings or other _v,._,_,.
restrictions. NIPPLE |%_ .L_Ei_'_
• Must not beplugged or blocked. . ifashortshirk(lecSfflaf12.)tenlpe_tu_Ppressurer_tefvldveistobeinstalled
Must be of material listedfor hot water distribution. (,.shown),=nippleandCOUl:41ngmustbeused.
Must be installed so as to allow complete drainage of "Ifal°hg_laflk(2_°rl°rlgef)ist°beh"stalled'd°n°tuseth°hipp_eandC°_l_i_"
both the temperature-pressurerelief valve,and the dis-"InStallTemeqra_ur_-Fressurepcotec_eequipmentrequiredby localcodes_butnotless_hana c¢_nbina-
tionTemeqrature-PressareRelief Valvec_rtified&smeetin 1herequirementsfor ReliefValvesand
charge pipe. _ R.S_ _= _,.=.w==Su_s_.,_sz__ by.,,0_,.,0_ _=-
ingliu_iSocy _maintains " icinspe_onof p_oflistedeqJpme_or maledals,The valve
Must terminate at an adequate drain, mustbecdeflteq,p_ovtdeq_°d_b/_,orothen_tsew_leqsolhatalschaxgecane_onlywflhin_alches
above,or atar_'distancebdow 1healzucturalfloor,andcannotc_act anylivealecb_d pa_t."
•Must not have any valve between the relief valve and Fcrsafeo_ofthewalsrheatsr,lheRdietValvemustnoteqrefnoveqc_:.
tank.see manualheading- "Temperaturs-Pressure R_f Valve' forinstallalJonan_eql_ntenanceof Relief
12

Instructions for Installation (cont'd)
Filling the Water Heater STANDARD WIRING FOR
Tofill the water heater with water: SINGLE ELEMENT 240 VOLT
1.Close the waterheater &ain valve by turning the handle toTO ELECTRICPOWERSUPPLY
the right (clockwise). The drain valveis on the lowerfrontJUNCTION
of the water heater. BOX
2. Open the cold water supplyvalve to the waterheater. BLACK
NOTE: The cold water supplyvalvemustbe left open RED
when thewater heater is in use.
3. To insure complete tilting of thetank,allow airto exit by
opening the nearest hot waterfaucet. Allow water to run
untila constant flow is obtained.This will let air out of the
water heater and the piping.
ACAUTION
Never use this water heater unless it is completely
full of water. To prevent damage to the tank and
heating element, the tank must be filled with
water. Water must flow from the hot water faucet
before turning "ON"power.
4. Check all new water pipingfor leaks. Repair as needed.
Wiring Diagrams HEA.NGELEMENT
STANDARD WIRING FOR WIRING FOR 3 WIRE LEAD WATER HEATERS
2 WIRE LEAD WATER HEATERS NON-SIMULTANEOUS OPERATION240VOLT
NON-SIMULTANEOUS OPERATIONDOUBLE ELEMENT
240 VOLT DOUBLE ELEMENT
TO ELECTRIC
POWERSUPPLY YELLOW -- THREETYPES
OF FIELD
_E CONNECTIONS
BLACK[YOU MAY HAVE
1.TIME CLO_K SWITCH
OPERATESBOTTOM ELEMENT ONLY
UPPERE.C.O. &, TO ELECTRIC, , TOTIME
POWER SUPPLY I_1 L2[_2E_ CLOCK SWITCHTHERMOSTAT
im. JUNCTION
YELLOLACK
UPPER 2. "OFF PEAK_METER
HEATING ELEMENT OPERATESBOTTOM ELEMENT ONLY
TO ELECTRIC LI L2"_'TO "OFF PEAK
E_ POWERSUPPLY_-I L2_t METER
J_LA JNCTIONBOX
YELLO CK
..g
== 3. FOR TWO W/RE CONNECTION
TOELECTRIC, t
POWER SUPPLY L_I L2
]W_flkA JNCIIONBOX
YELLO CK
HEATINGELEMENT
Note: SomeLower Hi-Temp Limit switches have4 termi-
may
LOWERnals. Use only the2 terminals on left.
HEATINGELEMENT 13

Instructions for Installation (cont'd)
Wiring _i,CAUTIONC. Flexible metal conduit or 3 metallic tubing shall be permit-
Neveruse thiswater heaterunless it iscompletely ted forgrounding if all the following conditions are met:
full of water.To prevent damage to the tank and 1.The length in anyground return path doesnot exceed
heating element, the tank must be filled with 6 feet.
water. Water must flow from the hot water faucet 2. The circuit conductors contained therein are protected
before turning on power, by overcurrent devices rated at 20 amperes or less.
3. The conduit or tubing is terminated in fittings
You must provide all wiring of the proper size outside of the approved for grounding.
water heater. You must obeylocal codes and electric company Forcomplete groundingdetails and all allowable exceptions,
requirements when you install this wiring, refer to the latest edition of the National Electrical Code.
If you are not familiar with electric codes and practices,or if 4. A standard 1/2"conduit opening has been made in the water
you have any doubt,even the slightest doubt,in your ability toheater junction box for the conduit connection.
connect the wiring to this water heater,obtain the service of a 5. Wiring Diagrams (See "Wiring Diagrams" Section) have
competent electrician. Call Maytag Customer Service at been supplied showing the twomost common types of con-
1-800-788-8899 for an authorized servicer, nections between the water heater and the power supply.
You can easily see which type connection you have by
WARNING removing the junction box cover on top of the water heater.
WATER HEATERS EQUIPPED FOR ONE VOLTAGE A.TwoWire Connection Diagrams: is the most common
ONLY: This water heater is equipped for one type requiring you to simply connect red to red, black to black,
voltage only. Check the rating plate near the bot- and the ground wire to the green ground screw in the june-
tom access panel for the correct voltage. DO NOT tion box of the water heater.
use this water heater with any voltage other than B. ThreeWire ConnectionDiagram:is used when you are
the one shown on themodel rating plate. Failure to connecting the water heater to power asupply that has a
use the correct voltage can cause problems which
can result in DEATH,SERIOUS BODILY INJURY,OR "Time Clock" or "OffPeak"Meter. To make these connec-
PROPERTY DAMAGE. If you have any questions or tions refer to block I or 2 in this wiring diagram for the type
doubts consult your electric company, of system you have.
NOTE:If you have purchasedathree wire connection
ACAUTION water heater butyouarenoton a"Time Clock"or "Off
If wiring from your fuse box or circuit breaker box Peak" meterandhaveastandardtwowireconnection
was aluminum for your old water heater;,replace it power supply, simplyfoUow the connection diagram in
with copper wire. If you wish to reuse the existing block 3 of the Three Wire Connection Diagram.
aluminum wire, have the connection at the water
heater made by a competent electrician. Call 6. Use wire nuts and connect the power supply wiring to the
i Mayta_Customer Service at %800-788-8899 for an ,. .
authorized servicer, wiresinside the water heaters junction.
1. Provide a way to easily shut off the electric power when 7. The water heater must be electrically "grounded" by the
working on the water heater, This could be with a circuit installer. A green ground screw has been provided on the
breaker or fuse block in the entrance box or a separate dis- water heater's junction box. Connect ground wire to this
connect switch, location.
8.Replace thewiring junction cover using the screw provided.
2. Install and connect a circuit directly from the main fuse or
circuit breaker box. This circuit must be the right size and
have its own fuse or circuit breaker. Refer to the chart in
the "ProductSpecifications" section for the correct size
wire and fuse or circuit breaker.
3. If metal conduit is used for the grounding conductor: co
A. The grounding electrode conductor shall be of copper,
aluminum,orcopperelad aluminum.The material shall_GsG__
be of one continuous length without a splice orjoint.
B. Rigid metal conduit,intermediate metal conduit,or
electrical metallic tubing may be used for the grounding
means if conduit or tubing is terminated in fittings
approved for grounding. 14

Instructions for Installation (cont'd)
Installation Checklist COLD
1. Whether or not the element conversion is made, the modelHOT /*,1[
rating plate must be marked. Using a hard point ink pen, -"
check the appropriate block within the model rating plate,
which is located adjacent to the lower access panel.
2. Is the fuse or circuit breaker size correct as shown in the
chart in the "Product Specifications" section? CONDUIT
3. Are the wires from the circuit breaker or fuse service to the_ERATURE-
water heater's junction box on the correct wire size (gauge) as r"-====_ PRESSURE
shown in the chart in the "Product Specifications" section? _RELIEFVALVE
4. Is thenew temperature-pressnre relief valve properly
installed,and piped to an adequate drain? See
"Temperature Pressure Relief Valve" in the "Instructions
for Installation" section. (Donotcapor
plug)
5. Is the water heater completely filled with water? See
"PilPng the Water Heater" instruct'ons in the 'Instructions
for Installation" section.
6. Will a water leak damage anything? See "Locating the
New Water Heater" in the "Instructions for Installation"
section.
6"AIRGAP
7. Are the cold and hot water lines connected to the water
heater correctly? See 'Water P'p'ng"instructions in the
Instructions for Installation section. FLOORDRAIN
8. Is there adequate clearance for maintenance aroundthe
water heater?
ELECTRICWATERHEATER Boo
9. Do you need to call your electric company to check your ,_,, _ Moo=_ _ ,_
wiring? ] ]
U.L
w_ i_c_'cL._mT_ _i psl.
I I r I --ipdmttlffi,_l
_warts warmF_
®May_ag is a Trzcd_kof Mayteg Corpoc_onacid
is Used under Ucense to StBte Inciustr _s,IN
MODELRATING PLATE
15

Service and Maintenance
Temperature Regulation
_WARNING ]
HOTTER WATER CAN SCALD: Water heaters are|LOWERTHERMOSTAT
intended to produce hot water. Water heated to al WITHHIGHLIMIT
temperature which will satisfy clothes washing,|
dish washing, and other sanitizing needs can scald/
and permanently injure you upon contact. Some
people are more likely to be permanently injured by
hot water than others.These include the elderly,
children, the infirm, or physically/mentally handi- LOWERTHERMOSTAT
capped. If anyone using hotwater in your home fits WITHOUTHIGHLIMIT
into oneof these groups or if there is a local code or
state law requiring a certain temperature water at
the hot water tap,then you must take special pre- __7-_"_
cautions. In addition to using the lowest possible
temperature settingthat satisfies your hot water Ol
needs,a means such as a mixing valve, should be _F
used at the hot water taps used by these people or _i_";;":,_:°_
at the water heater.Mixing valves are available at
plumbing supply or hardware stores.Follow manu-
tacturers instructions for installation of the valves.
Before changing the factory setting on the thermo-
stat,read the "Temperature Regulation"section in LOWER THERMOSTAT ADJUSTABLE
this manual. BEHIND LOWER ACCESSPANEL
AWARNING I
Never allow small children to use a hot water tap,
or to draw their own bath water. Never leave a Temperature Settings
child or handicapped person unattended in a bath-I
tub or shower. I HOT-Is a thermostat setting of approximately 120°F,
which w'tUsupplyhot water at the most eco-
Thermostats nomical temperatures.
The thermostat(s) ofthls water heaterhave been factory set at A-Isa thermostat settingof approximately 130°E
aposition whichapproximates 120°F (HOT) to reduce the
risk ofscaldinjury. B-Isathermostat setting of approximately 140°F.
The upper and/or lower thermostat(s) are factory set ata C-Isa thermostat setting ofapproximately150°E
position whichapproximates 120°F(HOT)andisadjustable
if a differentwater temperature is desired. Read all warnings VERY HOT-Isa thermostat settingof approximately 160°F.
in this manual andon thewater heater before proceeding. It is recommended that the dial beset lower
whenever possible.
NOTE: Water temperaturerangeof120°-140°F recom-
mended bymost dishwasher manufacturers.
UPPER THERMOSTAT ADJUSTABLE
BEHIND UPPERACCESSPANEL
16

Service and Maintenance (cont'd)
Thermostat Adjustments Temperature-Pressure Relief
Valve Operation
The upper and/orlower thermostat(s) have been factory set at
hot (approximately120°F) to reduce the risk of scald injury. The temperature-pressure relief valve must be manually oper-
The upperand/orlowerthermostat(s)areadjustableifa dif- atedat leastonceayear.
ferent water temperature is desired. Read all waxnings in the
"Temperature Regulation" section before proceeding. /TEMPERATURE-PRESSURE
/RELIEFVALVE
NOTE: It is not necessary toadjust the upper thermostat._smm_ A
However, flitis adjustedabove the factory setpoint of
120°F (HOT) it is recommendedthat it notbe set higher
than the lowerthermostat setting.
Toadjust the temperaturesetting for both upper andlower DISCHARGEPIPE
thermostats,proceed as follows:
1. Turn "OFF" the electric power to the water heater at the
junction box. AWARNING
The temperature-pressure relief valve must be
manually operatedat least once a year.Caution
AWARNING should be taken to ensure that (1) no one is in front
HAZARDOF ELECTRICAL SHOCK! Before removing of or around the outlet of the temperature-pres-
any access panels or servicing the water heater,sure relief valve discharge line,and (2) the water
make sure the electrical supply to the water heater manually discharged will not cause any property
is turned "OFF". Failure to do this could result in damage or bodily injury. Thewater may be
DEATH, SERIOUS BODILY INJURY, OR PROPERTY extremely hot.
DAMAGE. If after manually operating the valve, it fails to
completely reset and continues to release water,
immediately close the cold water inlet to the water
2. Take "OFF" the access panel, heater,follow the draining instructions,and
replace the temperature-pressure relief valve with
a new one.
3. The slotted adjustment (using a screwdriver) can be turned
clockwise (f'-_ to increase the temperature setting or
counter clockwise (¢_'x) to decrease the temperature Failure to install and maintain a new properly listed tempera-
setting, ture-pressure relief valve will release the manufacturer from
any claim which might result from excessive temperature or
4. Replace the access panel, pressure.
5. Turn "ON" the power supply. AWARNING
If the temperature-pressure relief valve on the
appliance weeps or discharges periodically, this
may be due to thermal expansion. Your water
heater may havea check valve installed in the
water line or a water meter with a check valve. Call
Mayta_Customer Service at 1-800-788-8899 for an
authorized servicer. Do not plug the temperature-
)ressure relief valve.
17

Serviceand Maintenance (cont'd)
Draining Thermostat Removal
The water heater shouldbe drained ifbeing shut down during 1. Turn "OFF" the electrical power to the water heater at the
freezing temperatures. Also periodic draining and cleaning of junction box.
sediment from the tank may be necessary.
1. Before beginning turn "OFF" the electric power supply to AWARNING
the water heater, HAZARD OF ELECTRICAL SHOCK!Before removing
any access panels or servicing the water heater, I
make sure the electrical supply to the water heater '
is turned "OFF'. Failure to do this could result in
AWARNING DEATH, SERIOUS BODILY INJURY, OR PROPERTY
HAZARD OF ELECTRICAL SHOCK!Before removinc DAMAGE.
any access panels or servicing the water heater I
make sure the electrical supply to the water heatel
is turned "OFF".Failure to do this could result in 2. Remove the access panel and the insulation blocL
DEATH, SERIOUS BODILY INJURY, OR PROPERTY
DAMAGE. 3, Lift out the tab as shown below to unclip the terminal cover
from the thermostat. The terminal cover can now be
2. CLOSE the cold water inlet valve to the water heater, removed from the thermostat.
3. OPENa nearby hot water faucet and leave open to allow
for draining,
4. Connect a hose to the drain valve and terminate to an ade-
quate drain or outdoors. I
5. OPENthe water heater drain valve to allow for tank
draining.
NOTE: If thewater heater is going to be shutdown and
drained foran extendedperiod, the drain valveshould be
left open with hose connected allowing water to termi-,_
nate toan adequate drain. -.
6. Close the drain valve.
7. Follow "Fillingthe Water Heater" instructions in the
Instructions forInstallation section. LOWERTHERMOSTAT UPPERORLOWER
WITHOUTHIGHLIMIT THERMOSTATWITH
HIGHLIMIT
8. Turn "ON" power to the water heater.
4. Remove the two wires attached to the thermostat.
ACAUTION I
Never use this water heater unless it is completely I 5. Removethethermostatfrombehindthethermostatbracket.
full water. To prevent damageto the tankand heat-
ing element, the tank must be filled with water. I
Water must flow from the hot water faucet before 6. Disconnect wires from thermostat andslide out ofthebracket.
turning"ON"power. 7. Place the new lower thermostat in the bracket making sure it
fits firmly against the tank.
8. Attach the wires to the new thermostat,
NOTE: Some of theterminals may require straight-in
wiring through aneye-openlng. If wires are now looped, re-
.. 3 Pt* o
cut and stripware/s toast_ughtlengtharldmsert.
18

Service and Maintenance (cont'd)
Thermostat Removal (cont'd)
9.Put plastic terminal cover back in place. 3.Attach a hose to the water heater drain valve and put the
other end in a floor drain or outdoors. Open the water
10. Replace the insulation block to cover the thermostat, heater drain valve. Open a nearby hot water faucet which
will relieve pressure in the water heater and speed draining.
11. Replace accesspanel, then turn the electric power on.
Element Cleaning/
Replacement
NOTE: These instructions arewritten for element cleaning
and element replacement for thelowerelement. If it is nec-
essary to clean or replace the upper element, then repeat I
AWARNING
theseinstructions. I
The water passing out of the drain valve may be
extremely hot. To avoid beincj scalded, make sure all I
To removethe element from your tankin order to clean or connections are tight and that the water flow is
replace it: d rected away from any person.
1. Before beginning turn "OFF"the electric power supply to
the water heater. 4.Remove the two screws securing the access panel, and
remove panel.
AWARNING a
HAZARD OF ELECTRICAL SHOCK] Beforeremoving
any access panels or servicing the water heater, 5. Remove the block of insulation to expose the terminal
make sure the electrical supply to the water heater
isturned "OFF".Failure to do this could result in cover,
DEATH, SERIOUS BODILY INJURY,OR PROPERTY
DAMAGE.
2. Turn offthe water supply to the waterheater at the water
shutoffvalve or water meter. (_j_ _,
19

Service and Maintenance (cont'd)
6. Lift out the tabas shown to unclip the terminal cover from_r'_
the thermostat. The terminal cover can now be removed
from the thermostat.
11.Close the water heater drain valve by turning the handle
to the right (clockwise). The drain valve is on the lower
front of the water heater.
12. Open the cold water supply valve to the water heater.
NOTE: The cold water supply valve must be left open
when the water heater is in use.
13. To insure complete filling of the tank, allow air to exit by
LOWERTHERMOSTAT UPPERORLOWER opening the nearest hot water faucet.Allow water to run
WITHOUTHIGHUMIT THERMOSTATWITH until a constant flow is obtained. This will let air out of
HIGHLIMIT the water heater and the piping.
7.Disconnect the two wires on the element and unscrew the ACAUTION
old element from the tank. Never use this water heater unless it is completely
full of water.To prevent damage to the tank and
heating element,the tank must be filled with water.
_- X_'_'_'__ turningWatermuStnoN.flOWpower.fromthe hot water faucet before
14. Check element for water leaks. If leakage occurs, tighten
element or repeat steps 2 and 3, remove element and
reposition gasket. Then repeat steps 10 through 14.
15. Reconnect the two wires to the element and then check
to make sure the thermostat remains firmly against the
surface of the tank.
8. Clean the area around the element opening. Remove any
sediment from or around the element opening and inside _"
the tank.
9. If you are cleaning the element you have removed, do so
by scraping or soaking in vinegar or a de-liming solution.
AWARNING
Replacement elements must (1) be the same volt-_,_
age and (2) no greater wattage than listed on the
model rating plate affixed to the water heater.
10.A new gasket should be used in all cases to prevent a pos-
sible water leak. (See Element Gasket in the Repair Parts
Chart). Place the new element gasket on the thread side
of the cleaned or new element and screw into tank, secur-
ing tightly using an element wrench.
20