MB QUART NAUTIC NT1-116 Instruction Manual

The NT1 clamping system is designed for towers
and support structures that utilize ROUND tubing.
Oval tubing and flat structures will not work with
this clamp. The NT1 clamp can be used with tube
diameters from 1.5” up to 2.75”. Included are
separate bushing sets for all tube sizes at 1/8”
increments. Refer to the table below to determine
your configuration.
Choose a suitable
mounting location
Mounting Location
Dimensions
CAUTION
Always consider consulting a professional audio installer
before installing new speakers. Many manufacturers locate
speakers behind interior panels that require special tools to
remove. Be careful and take your time.
If you are using the speaker wire supplied with your new
speakers make sure that you run the speaker wires only
through safe areas. Do not let speaker wire make contact with
metal edges or hot engine components.
Congratulations on your choice of a MBQuart Subwoofer.
This “Quick Start” Installation guide is meant to help
you complete a basic installation. For more detailed
information on system setting, speaker and subwoofer
configuration, and full specifications by model, visit our
website at mbquart.com
It’s a good idea to confirm that you have purchased the
correct size speakers to fit your application. If you have any
reservations about being able to complete the installation
yourself, we recommend contacting a professional.
Before you start
Carefully select a route for the audio signal
wires. If using existing speaker wires, confirm
that the wire is in good shape and not
shorted. In the case of an illuminated model,
route a positive and negative wire from a
switched +12V source. Avoid routing wires
through dangerous areas.
Route signal and
illumination wires
Wiring
230mm
9.04”
104mm
4.08”
44mm
1.73”
274mm
10.78”
215mm
8.47”
Tube
Diameter Tube Circumference Clamp Top Bushing Bottom Bushing
1.5 4.71 A 1.50 1.50
1.625 5.10 A 1.63 1.63
1.75 5.50 A 1.75 1.75
1.875 5.89 A none 1.88
2 6.28 B 2.00 2.00
2.125 6.68 B 2.13 2.13
2.25 7.07 B 2.25 2.25
2.375 7.46 B 2.38 2.38
2.5 7.85 B 2.50 2.50
2.625 8.25 B 2.68 2.68
2.75 8.64 B none none
Black ...................................... Audio signal negative
Black w/white stripe ................ Audio signal positive
Black ....................................... Illumination negative
Red ......................................... Illumination positive

Quick Start
Installation Guide
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period.Componentsthatprovetobedefectiveinmaterialsandworkmanshipunderproperinstallation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
Hifonics products are designed and engineered in the USA by
847-540-7700
www.maxxsonics.com
NT1-116
NT1-116
NT1-116L
NT1-116L
NT1-120
NT1-120
NT1-120L
NT1-120L
NAUTIC
NAUTIC
MBQ NT QSG 01 - rev2
Your NT1 speakers can be aligned to “hang straight”
on an angled tube by loosening, rotating and
re-mounting the speaker. Just behind the speaker
mounting holes is a series mounting holes that can
be used to align the speaker in the pod.
If you have purchased an illuminated version, consider getting an N1-RC remote
control. The remote allows you to adjust color, speed and brightness of the
illumination. Check with an authorized MBQuart retailer or check our website
www.mbquart.com for further details.
Adjust the speaker
alignment
Grill alignment
Illumination control