MCOHome MH-S512 User manual

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 1
Touch Panel Switch
MH-S512
Introduction
Touch Panel Switch is a wall switch with built-in Z-Wave module. It supports basic command
class，multi channel command class and multi channel association command class, which can control
all associated devices synchronously. This product can be included and operated in any Z-Wave
network with other Z-Wave certified devices from any other manufacturers.
Specifications
Power supply: 85~260VAC, 50/60Hz
Z-Wave frequency: 916MHz (IL).
Resistance load: 2*3.5A
*LED load: <1A total
Installation Instructions
IMPORTANT:
A qualified electrician with the understanding of wiring diagrams and knowledge of electrical
safety should complete the installation inside the main circuit box (normally outside your house)
Read all instructions and documentation and save for future reference
Step1 Preparing
CAUTION: Cut off power supply at circuit breaker or fuse before installation to avoid fire, shock or
death!
Step2 Wiring ( standard strip length: 6-8mm )
1. Separate the device into two parts: the touch panel and the bottom.
2. Connect Hot Line to “L” on the bottom.
3. Connect Neutral Line to “N”.
4. Connect Load wire to “L1&L2”.
5. Secure the bottom onto the junction box with two screws, and then mount the touch panel back.
* Note: If a higher output needed, pls choose model MH-S511H instead. (LED load: <10A, inrush current<165A/ 20ms )

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2
Operation
INCLUDING the device into Z-Wave network:
1. Set controller into INCLUSION mode. Follow instructions provided by controller manufacturer.
2. Press and hold any key on the panel for 8 seconds.
Note: If inclusion is successful, all INDICATION LEDs on the panel will turn green, and all switches
will turn on.
EXCLUDING the device from Z-Wave network:
1. Set controller into EXCLUSION mode. Follow instructions provided by controller manufacturer.
2. Press and hold any key on the panel for 8 seconds.
Note: If the exclusion is successful, all INDICATION LEDs on the panel will turn orange, and all
switches will turn off. The exclusion will delete all association data.
Turning on/off the device:
The device can be controlled by:
Pressing any key.
Sending commands through controller or gateway.（the command classes which support this
function are Basic Command Class, Binary Command Class, Switch All Command Class, and
Multi Channel Command Class.）
Multi Channel Control:
The switch can be controlled by command “MULTI_CHANNEL_ENCAP” in the command class
“COMMAND_ CLASS_MULTI_CHANNEL”.
Byte
Name
1
COMMAND_CLASS_MULTI_CHANNEL
2
MULTI_CHANNEL_CMD_ENCAP
3
Source End Point
4
Destination End Point
5
COMMAND_CLASS_SWITCH_BASIC or COMMAND_CLASS_SWITCH_BINARY
6
BASIC_SET/BASIC_GET or BINARY_SET/BINARY_GET
7
Value ( 0xFF -- ON 0x0 -- OFF )
Multi ChannelAssociation:
To set association groups by the command “COMMAND_CLASS_MULTI_CHANNEL_
ASSOCIATION”.
The device supports 3 association groups (AG). The 1st AG is used for reporting devices’state to
the controller if any changes happen. This group supports one Node, which suggested to be controller
Node. The rest 2 AGs is used for switching associated devices，and it can support up to 5 nodes or
terminals.
For the 1st AG, a report will be sent to associated controller when any state changes happen in
other group(s). For the rest 2 AGs, the touch panel switch will send Basic Set Command to related
association groups when setting switch state by gateway or key-pressing. Then the switch states of
associated devices and their related key will be synchronic (S1-AG2, S2-AG3).

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 3
Scene Function:
As a Scene device, it supports “Scene Activation CC”and “Scene Actuator Conf CC”,which
make the device can be added into any scene , and supports 255 Scene ID. In parameter item4, users
can configure which external switch will respond the scene CC .
Parameters Setting:
Add
Function
Byte
Options
Default
Remark
1
Switch state saved or
not when power
failure
1
0x00 not saved，switch will be off when
powered again
0x01 saved，switch will keep the same
state when powered again
0x01
2
RESERVED
3
LED Backlit
brightness level
1
0x00 LED disabled
0x01~0x0A Min level-Max level
0x0A
4
Scene respond
1
0x00 All switches respond Scene CC
0x01 only S1 respond
0x00
5
ALL ON/ALL OFF
1
0x00 forbid ALL ON, forbid ALL OFF
0x01 forbid ALL ON, allow ALL OFF
0x02 allow ALL ON, forbid ALL OFF
0xFF allow ALL ON, allow ALL OFF
0xFF
255
Factory setting
1
0x55 restore factory setting
write only
Restoring Factory Settings
Pls follow the EXCLUDING operation to restore the factory setting.
SAFETY NOTICE
1. Flush-mount only into a UL/ETL/CE certified plastic junction box and switch panel cover. The
minimum size should be 90*60*50mm, minimum Volume is 270cm3.
2. Use Copper Conductors Only.
3. CAUTION - Risk of Electric Shock - More than one disconnect switch may be required to
de-energize the equipment before servicing.
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USAonly)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 4
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
1-year Limited Warranty
We warrant this product to be free from defects in material and workmanship under normal and proper use for one
year from purchase date of the original purchaser. We will, at its option, either repair or replace any part of its products
that prove defective by reason of improper workmanship or materials. THIS LIMITED WARRANTY DOES NOT
COVER ANY DAMAGE TO THIS PRODUCT THAT RESULTS FROM IMPROPER INSTALLATION, ACCIDENT,
ABUSE, MISUSE, NATURAL DISASTER, INSUFFICIENT OR EXCESSIVE ELECTRICAL SUPPLY,
ABNORMAL MECHANICAL OR ENVIRONMENTAL CONDITIONS, OR ANY UNAUTHORIZED
DISASSEMBLY, REPAIR OR MODIFICATION. This limited warranty shall not apply if: (i) the product was not used
in accordance with any accompanying instructions, or (ii) the product was not used for its intended function. This
limited warranty also does not apply to any product on which the original identification information has been altered,
obliterated or removed, that has not been handled or packaged correctly, that has been sold as second-hand or that has
been resold contrary to Country and other applicable export regulations.