MCOHome MH-S312-EU User manual

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2013 1
Touch Panel Switch
MH-S312/MH-S314-EU
Introduction
MCOHome Touch Panel Switch is a wall switch with built-in Z-Wave module. It supports basic
command class，multi channel command class and multi channel association command class, which
can control all associated devices synchronously. This product can be included and operated in any
Z-Wave network with other Z-Wave certified devices from any other manufacturers.
Specifications
EU: S312 - 5A max output (each channel); S314 - 3A max output (each channel)
Installation Instructions
IMPORTANT:
 A qualified electrician with the understanding of wiring diagrams and knowledge of electrical
safety should complete the installation inside the main circuit box (normally outside your house)
 Read all instructions and documentation and save for future reference
Step 1 Preparing
CAUTION: Cut off power supply at circuit breaker or fuse before installation to avoid fire, shock or
death!
Step 2 Wiring
1. Connect Hot Line to “L”.
2. Connect Neutral Line to “N”.
1. Connect Load wire to “1&4”.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2013 2
Operation
INCLUDING the Touch Panel Switch into your network
1. Put the controller into INCLUSION mode. Follow the instructions provided by the controller
manufacturer.
2. Press and hold any key on the panel for 3 seconds.
Note: If inclusion is successful, all INDICATION LEDs on the panel will light up, and all switches
will turn on.
EXCLUDING the Touch Panel Switch from your network
1. Put the controller into EXCLUSION mode. Follow the instructions provided by the controller
manufacturer.
2. Press and hold any key on the panel for 3 seconds.
Note: If the exclusion is successful, all INDICATION LEDs on the panel will go out, and all switches
will turn off. The exclusion will delete all association data.
Turning on/off the Touch Panel Switch
The Touch Panel Switch can be controlled by:
 Pressing any key.
 Sending commands through controller or gateway.（the command classes which support this
function are Basic Command Class, Binary Command Class, Switch All Command Class, and
Multi Channel Command Class.）
Multi Channel Control
The switch can be controlled by command “MULTI_CHANNEL_ENCAP” in the command class
“COMMAND_ CLASS_MULTI_CHANNEL”.
Byte Name
1 COMMAND_CLASS_MULTI_CHANNEL
2 MULTI_CHANNEL_CMD_ENCAP
3 Source EndPoint
4 Destination EndPoint
5 COMMAND_CLASS_SWITCH_BASIC or COMMAND_CLASS_SWITCH_BINARY
6 BASIC_SET/BASIC_GET BINERY_SET/BINERY_GET
7 Value
Multi Channel Association
To set association groups by the command “COMMAND_CLASS_MULTI_CHANNEL_
ASSOCIATION”.
The switch supports 5 association groups. The first four groups are used for switching associated
devices（switch N controlling group N），and each group can support up to 5 nodes or terminals. The
5th association group is used for reporting devices’ state to the controller if any changes happen. This
group supports one node, which defaults to controller node. Please refer to “Command Class
Specification” for detail information.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2013 3
For the first four groups, the touch panel switch will send basic set command to related
association groups when setting switch state by gateway or key-pressing. Then the switch states of
associated devices and their related key will be synchronic. For the 5th group, a report will be sent to
associated controller when any state changes happen in the other four groups.
Restoring Factory Settings
Press and hold any key on the panel for 10 seconds for restoring factory settings. Then the node
information and association data will be deleted.
Note：If factory settings are restored, all INDICATION LEDs on the panel will go out, and all
switches will turn off with a beep of buzzer.
1-year Limited Warranty
MCOHome warrants this product to be free from defects in material and workmanship under
normal and proper use for one year from purchase date of the original purchaser. MCOHome will, at
its option, either repair or replace any part of its products that prove defective by reason of improper
workmanship or materials. THIS LIMITED WARRANTY DOES NOT COVER ANY DAMAGE TO
THIS PRODUCT THAT RESULTS FROM IMPROPER INSTALLATION, ACCIDENT, ABUSE,
MISUSE, NATURAL DISASTER, INSUFFICIENT OR EXCESSIVE ELECTRICAL SUPPLY,
ABNORMAL MECHANICAL OR ENVIRONMENTAL CONDITIONS, OR ANY
UNAUTHORIZED DISASSEMBLY, REPAIR OR MODIFICATION. This limited warranty shall not
apply if: (i) the product was not used in accordance with any accompanying instructions, or (ii) the
product was not used for its intended function. This limited warranty also does not apply to any
product on which the original identification information has been altered, obliterated or removed, that
has not been handled or packaged correctly, that has been sold as second-hand or that has been resold
contrary to U.S. and other applicable export regulations.