MCOHome MH-S513-US User manual

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2013 1
Touch Panel Switch
MH-S513-US
Introduction
MCOHome Touch Panel Switch is a wall switch with built-in Z-Wave module. It supports basic
command class，multi channel command class and multi channel association command class, which
can control all associated devices synchronously. This product can be included and operated in any
Z-Wave network with other Z-Wave certified devices from any other manufacturers.
Specifications
Power supply: AC120V, 60Hz
Frequency: 908.42MHz
Max load: 5A each channel
Load type: Incandescent, Fluorescent, Ballast, Motor, CFL
Installation Instructions
IMPORTANT:
A qualified electrician with the understanding of wiring diagrams and knowledge of electrical
safety should complete the installation inside the main circuit box (normally outside your house)
Read all instructions and documentation and save for future reference
Step1 Preparing
CAUTION: Cut off power supply at circuit breaker or fuse before installation to avoid fire, shock or
death!
Step2 Wiring
1. Connect Hot Line to “L”.
2. Connect Neutral Line to “N”.
3. Connect Load wire to “L1--L3”.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2013 1
Operation
INCLUDING the Touch Panel Switch into your network
1. Set the controller into INCLUSION mode. Follow instructions provided by controller
manufacturer.
2. Press and hold any key on the panel for 3 seconds.
Note: If inclusion is successful, all INDICATION LEDs on the panel will turn green, and all switches
will turn on.
EXCLUDING the Touch Panel Switch from your network
1. Set the controller into EXCLUSION mode. Follow instructions provided by controller
manufacturer.
2. Press and hold any key on the panel for 3 seconds.
Note: If the exclusion is successful, all INDICATION LEDs on the panel will turn orange, and all
switches will turn off. The exclusion will delete all association data.
Turning on/off the Touch Panel Switch
The Touch Panel Switch can be controlled by:
Pressing any key.
Sending commands through controller or gateway.（the command classes which support this
function are Basic Command Class, Binary Command Class, Switch All Command Class, and
Multi Channel Command Class.）
Multi Channel Control
The switch can be controlled by command “MULTI_CHANNEL_ENCAP”in the command class
“COMMAND_ CLASS_MULTI_CHANNEL”.
Byte
Name
1
COMMAND_CLASS_MULTI_CHANNEL
2
MULTI_CHANNEL_CMD_ENCAP
3
Source End Point
4
Destination End Point
5
COMMAND_CLASS_SWITCH_BASIC or COMMAND_CLASS_SWITCH_BINARY
6
BASIC_SET/BASIC_GET or BINERY_SET/BINERY_GET
7
Value ( 0xFF -- ON 0x0 -- OFF )
Refer to “Z-Wave Command Class”for detail information, or consult the information provided by
controller/ gateway manufacturer.
Multi ChannelAssociation
To set association groups by the command “COMMAND_CLASS_MULTI_CHANNEL_
ASSOCIATION”.
The switch supports 4 association groups. The first three groups are used for switching associated
devices（switch N controlling group N）， and each group can support up to 5 nodes or terminals. The
4th association group is used for reporting devices’state to the controller if any changes happen. This
group supports one node, which defaults to controller node.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2013 1
For the first three groups, the touch panel switch will send basic set command to related
association groups when setting switch state by gateway or key-pressing. Then the switch states of
associated devices and their related key will be synchronic. For the 4th group, a report will be sent to
associated controller by it when any state changes happen in other groups.
Restoring Factory Settings
Press and hold any key on the panel for 10 seconds for restoring factory settings. Then the node
information and association data will be deleted.
Note：If factory settings are restored, all INDICATION LEDs on the panel will turn orange, and
all switches will turn off.
FCC Warning (Part 15.21) (USAonly)
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
1-year Limited Warranty
MCOHome warrants this product to be free from defects in material and workmanship under
normal and proper use for one year from purchase date of the original purchaser. MCOHome will, at
its option, either repair or replace any part of its products that prove defective by reason of improper
workmanship or materials. THIS LIMITED WARRANTY DOES NOT COVER ANY DAMAGE TO
THIS PRODUCT THAT RESULTS FROM IMPROPER INSTALLATION, ACCIDENT, ABUSE,
MISUSE, NATURAL DISASTER, INSUFFICIENT OR EXCESSIVE ELECTRICAL SUPPLY,
ABNORMAL MECHANICAL OR ENVIRONMENTAL CONDITIONS, OR ANY
UNAUTHORIZED DISASSEMBLY, REPAIR OR MODIFICATION. This limited warranty shall not
apply if: (i) the product was not used in accordance with any accompanying instructions, or (ii) the
product was not used for its intended function. This limited warranty also does not apply to any
product on which the original identification information has been altered, obliterated or removed, that
has not been handled or packaged correctly, that has been sold as second-hand or that has been resold
contrary to Country and other applicable export regulations.