Medisante BC800 3G User manual

BC800 3G
Body Weight Scale
Instruction Manual

BC800 3G
Summary
Instruction Manual
Package contents
Display Indicators
Operating Instructions
Important Safety Information
Specification

Package contents
Intended use: The Body Weight Scale BC800 3G is a digital monitor for home/domestic use which
measures weight of persons 18 years of age or more.
Read the instruction manual before using the device
Body Weight Scale
BC800 3G
4x1.5V AAA
Alkaline batteries
1. Insert batteries
Place the scale upside down on a flat
surface being careful not to scratch it.
Remove the battery cover and insert
4×1.5V AAA alkaline batteries with correct
polarity.
01
02
Weight & measurement log:
If shows up, then total number of measurements
sent is displayed.
If shows up, then total number of measurements
still stored on the scale is displayed.
Telecom signal strength
Data send in progress
Data send status *
Units
* Data sent successfully
Data send failure
Display Indicators
Remove battery cover.
Insert batteries.
Replace battery cover.
Batteries are low and need to be replaced.
Overload Indicator
Scale is overloaded (max. 180 kg, 396 lbs, 28.3 st)
Low Battery Indicator
01
02
03
Date (dd:mm:yyyy)
Time (hh:mm)

Important Safety Information
the glass.
Keep packaging materials away from children.
Store the Body Weight Scale BC800 3G hori-
zontally, not vertically.
If the measurement appears inaccurate or if
the LCD display does not show any figures,
please check that the batteries are correctly
inserted and the battery contacts are clean.
If the Body Weight Scale BC800 3G will not
be used for an extended period of time,
remove the batteries from the Weight Scale
BC800 3G and store it properly. Do not store
other objects on top of it.
Please use the device in a dry and clean envi-
ronment, and place the device on a flat ground
before use.
Do not use hot water, volatile oil or rosin oil to
clean the scale.
Please store at room temperature, keep in a
dry and cool place and avoid sun exposure.
Do not run or jump near the Body Weight
Scale BC800 3G.
This product is applied parts(type BF).No
maintenance required during the product life
cycle.
Please read the entire instruction manual and
safety precautions before using the Body
Weight Scale BC800 3G.
Unusual measurement values should be dis-
cussed with your doctor or health care pro-
fessional.
Never change the dosage of any prescribed
medications without first consulting your doc-
tor or health care professional.
Always perform the measurements on a hard
and flat surface. Uneven floors may affect the
readings.
If necessary, clean the Body Weight Scale
BC800 3G with a damp cloth and a small
amount of dishwashing liquid. When the sur-
face is dirty.
Never immerse the scale in water or rinse it
under running water.
Protect the Body Weight Scale BC800 3G
against knocks, moisture, dust, chemicals,
drastic changes in temperature and electro-
magnetic fields.
Keep the Body Weight Scale BC800 3G away
from any sources of heat.
Never step on the outer edge of the glass.
This could cause the scale to tip or damage
→
→
→
→
→
→
→
→
→
→
→
→
→
→
→
→
→
Automatic Shutdown
If no measurement is being taken, the scale will automatically turn off in 10 seconds.
2. Operating Instructions
Place the scale on a hard, flat surface.
Step on the scale and remain still during
measurement.
When the “data send in progress” indicator
is displayed, the data is being sent and you
may step off the scale.
01
02
03
After a period of time, the data send status
will be displayed. If it shows a“data send
failure”, move the scale to a new location
and try again.
04
Notes
→ Weight measurements are possible withshoes and socks on.
→ Calibration: if you place the body weight scale BC800 3G at new place, quickly step with one on
it, until the display turns on. Step off and wait until the calibration gets performed(10-15 seconds)and
the display switches off.
→ If there is no signal strength indicator and you continue to receive a data send failure, contact your
distribution partner.
→ user should clean the glass surface before use.
→ Please contact [e-mail] for troubleshooting and maintenance.

To Avoid Injury
• Only use this device for its intended use and in accordance with the instruction manual.
• Do not use the device if it is damaged in any way.
operation environment:
Transportation and storage environment:
Temperature (ºC),/Relative Humidity
(%)/Atmospheric Pressure (kPa):
10~40 ºC /15~90%RH / 70 kPa
~106 kPa
Home healthcare.
Temperature (oC),/Relative Humidity
(%)/Atmospheric Pressure (kPa):
-25~40°C / 10~95%RH / 70 kPa
~106 kPa
(1)
(2)
(1)
EBM Technologies Inc. will provide circuit
diagrams, component part lists, descriptions,
calibration instructions to assist to service
personnel in parts repair.
300 Measurements (Info: the Battery life
depends on the used batteries.
The time required for scale to warm from
-25oC between uses until scale is ready for its
intended use when the ambient temperature
is 20oC is 2 hours.
The time required for the scale to cool from
40oC between uses until the scale is ready for
its intended use when the ambient tempera-
ture is 20oC is 2 hours.
If the degraded sensors and electrodes, or
loosened electrodes, that can cause weight
measurement failure .please contact EBM
Technologies Inc.
The waste products and batteries should fol-
low the domestic waste disposal regulation.
Product life expectancy: 5 years
→
→
→
→
→
→
→
→
Warning
• known contraindication: People are equipped with Pace Maker or other implant device shall not use
this scale.
• Scale shall not be broke down or maintained in operation.
• Scale release a week current and it pass through the body. The current may affect electrical product
and cause erroneous operation. The failure may become the cause of major accidents.
• Do not use a mobile phone or low frequency therapy device near the Scale.
• Prohibit any modification of the scale, it may cause hazards.

FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End user must follow the specific operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established
by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg
averaged over one gram of tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body.
FCC compliance statement
changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV technician for help.

Specification
Sensors
Maximum Capacity
Increments
Measurements
Display
Fault indications
Data transmission
Operating environment
Frequency bands
Output power
Automatic shutdown
High precision strain gauge sensors
180 kg / 396 lbs / 28.3 st
0.1 kg / 0.2 lbs / 0.01 st
Weight
White backlight LCD display
Overload and low battery
Over a 3G/2G mobile connection
(with Vodafone SIM card inside)
Temperature 10~40°C (50~104°F)
Humidity 15 %~90 % RH
GSM/GPRS/EDGE: Dual band GSM 900/1800MHz
UMTS/HSPA+: Dual band UMTS 900/2100MHz
Class 4 (+33dBm ±2dB) for EGSM900
Class 1 (+30dBm ±2dB) for GSM1800
Class E2 (+27dBm ± 3dB) for GSM 900 8-PSK
Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK
Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI
Class 3 (+24dBm +1/-3dB) for UMTS 900, WCDMA FDD BdVIII
Yes, after 10 seconds
Symbol Description
Indicates the manufacturer’s serial number so that a specific
medical device can be identified.
Indicates a medical device that needs to be protected from
moisture.
Indicates the need for the user to consult the instructions for
use.
Indicates the need for the user to consult the instructions for
use for important cautionary information such as warnings and
precautions that cannot, for a variety of reasons, be presented
on the medical device itself.
Hereby, EBM Technologies Inc. declares that the radio equipment type BC800 3Gis in compliance
with directive FCC ID (FCC PART 22/24, IEEE 1528, KDB447498), IEC60601-1: 2005+A1:
2012, IEC60601-1-11: 2015, IEC606601-1-2: 2014, 2014/53/EU, 2014/30/EU, 2011/65/EU.
EBM Technologies Inc. declares that the medical device weight scale BC800 3G is listing in
FDA(Registered Establishment Number: 3004722076)

Manufacturer
EBM Technologies Inc.
5F. No. 516 Sec. 1 Neihu Road Taipei, Taiwan
Distribution by
Medisante’ USA, Inc.
Suite 14A, 2077 Center Avenue
[phone]
https://www.medisante-group.com/
[e-mail]
Instruction Manual - Version 4, 2020/06
© 2017 Medisanté. All rights reserved.
2AWYXBC800