Medline MDS89730R Installation guide

ALUMINUM FRAME
BATH STOOL
MDS89730R
User Instructions and Warranty
This Product Contains Dry Natural Rubber.
Este Producto Contiene Caucho Natural Seco.

General Warnings
To ensure the safe installation, adjustment, and operation of the Bath Stool, these instructions MUST
be followed. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY TO THE
USER OR DAMAGE TO THE PRODUCT. If you are unable to understand these warnings, cautions,
and instructions, contact a healthcare professional or dealer before attempting to use this equipment.
Warnings:
Prior to each use check to assure that all screws, joints and fittings
on the bath stool are tight.
DO NOT place bath bench on uneven surfaces.
DO NOT use if wobbly, unstable or not level.
DO NOT exceed user weight capacity of 300 lbs. (136 kg)
DO NOT stand on the bath stool.
DO NOT use the bath stool for anything but its intended purpose.
√ Excessive twisting or turning while seated on the bench may cause a loss of
balance and damage to the product.
√ Check rubber tips for rips, cracks or wear. If these conditions exist, DO NOT use
the bath bench and replace the tips immediately.
√ Check the bench for cracks or ruptures in the plastic. If you have concerns,
contact the manufacturer at 1-800-633-5463.
√ Check that all push buttons are fully protruded from the mainframe through the leg extensions
and are properly engaged.
√ Ensure all four legs are adjusted evenly and are free of any obstructions prior to use.
CONTENTS: 1. Stool Seat
2. Extension Legs
Figure 1

Assembly Instructions
Ensure that you have all of the necessary components before assembling your bath bench.
• 1 Bench –with preassembled main frame
• 4 Aluminum extension legs
1. Turn the bench seat (Figure 2) over to reveal the pre-assembled mainframes.
Figure 2
2. Note that each leg has 2 pushbuttons. 1 attachment push button and 1 adjustment pushbutton.
(Figure 3)
Figure 3
3. Take one leg and hold it so the rubber tip is up. Depress the push button at the top of the leg
extension (Figure 4) and insert the extension into one of the four leg assemblies.
Figure 4

4. Ensure the push button is properly engaged (Figure 5)
Figure 5
5. Repeat with the other three leg extensions.
6. Using the Adjustment Pushbutton, adjust the legs to desired height (Figure 6).
Figure 6
7. Adjust the height of the bench by first measuring the distance from the back of the user’s knee to
the floor. Using the chart below depress the push button (Figure C) into the appropriate slot.
Choose the appropriately numbered hole on leg for desired height.
Leg Adjustment
Hole
1
2
3
4
5
6
Bench Seat Height
14”
(35.56 cm)
15”
(38.1 cm)
16”
(40.64 cm)
17”
(43.18 cm)
18”
(45.72 cm)
19”
(48.26 cm)

8. Turn the stool upright and ensure all four rubber tips (Figure 7) rest evenly on the floor.
Figure 6
Cleaning
The bath bench can be easily cleaned with regular household cleaning products. Use a non-abrasive
cleaner with warm water. DO NOT use abrasive powders or scouring pads.
Maintenance
Periodically inspect the bath bench for damage or loose components.
Ensure all push buttons are protruded from the extension legs.
Check the rubber feet on the leg extensions for rips or wear. If any of these conditions exist, or if
they are missing, replace them immediately.

LIMITED WARRANTY
Your Medline product is warranted to be free of defects in materials and workmanship for the duration of use by the
original purchaser. This device was built to precise standards and carefully inspected prior to shipment. This limited
warranty is an expression of our confidence in the materials and workmanship of our products and assures years of
convenient, dependable service. In the event of a defect covered by this warranty, we will, at our option, repair or replace
the device. This warranty does not cover device failure due to owner misuse or negligence, or normal wear and tear. The
warranty does not extend to non-durable components, such as rubber accessories, which are subject to normal wear and
replacement.