MEFE CAT 68931 Soap User manual

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 1
[phone]
Free AU 1800 669 006
Installaon Manual
Automac Soap Dispenser
Wall Mount
CAT 68931 Soap | CAT 68931S
CAT 68932 Foam
Revision 2

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 2
[phone]
Free AU 1800 669 006
Contents
1. Before Use ...................................................................................................................... 3
1.1 Specicaons ................................................................................................................ 3
2. Installaon...................................................................................................................... 3
2.1 Installing the Spout .................................................................................................. 4
2.2 Installing the Control Box......................................................................................... 5
2.3 Connecon of Parts.................................................................................................. 5
2.4 Tesng for Use ......................................................................................................... 6
2.5 Rell or Replace Soap............................................................................................... 6
3. Care and Cleaning........................................................................................................... 7
3.1 Periodic Maintenance .............................................................................................. 7
3.2 Long-term Suspension of Use .................................................................................. 7
4. Diagram and Parts List ................................................................................................... 8

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 3
[phone]
Free AU 1800 669 006
Power Supply DC 6V (x4 1.5V Alkaline Baeries) or AC 100-240V
Sensor Detecon Range 5—150mm
Ambient Temperature 1-40°C
Humidity Max 90% RH
Soap Volume 0-1.5ml
Applicable Soap Viscosity 100-3800 cPs
Bole Volume Soap 1000ml / Foam 1500ml
Tubes Soap: 110cm outlet
Foam: 80cm inlet, soap line outlet 100cm, air line outlet 100cm, 110cm outlet
Sensor Cable 135cm
Power Cable 150cm
1. Before Use
• Please do not disassemble, repair or ret the products, unless stated otherwise. This could lead to electrical shock or
product breakdown.
• Please do not install the products in any environment with over 90% relave humidity.
• Please do not use the product in the place where freezing might occur.
• Please minimise exposure of the control box and power supply for longevity of use.
• Please handle with care to avoid damage to the unit or soap leakage.
• Please ensure that the power line separates from hot water line/tube.
• Please keep the detecng sensor scope clear to avoid interference.
• The designated soap liquid viscosity is strongly recommended to be used.
• Please install the power socket/outlet in the place where water cannot be reached or sprayed.
1.1 Specicaons
2. Installaon
Posion of Spout
If installing the dispenser beside a sensor op-
erated faucet, please ensure there minimum
120mm between the spout and water faucet
to avoid accidental acvaon.
Posion of Sink/Basin
Please make sure the distance between the mounted hole of the spout and counter
edge is not more than 80mm to ensure soap/foam is dispensed in the desired locaon.

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 4
[phone]
Free AU 1800 669 006
Posion of Control Box
1. Please make sure that the
length of the soap tube and
sensor cable are sucient
to connect with the control
box before choosing where
to install the control box.
2. If the length of the soap
tube is too long, it can be
cut to suitable length.
3. Please make sure there is
sucient space between
the base of the soap bole
and the oor to rell soap
or replace the bole.
2.1 Installing the Spout
1. Locate and mark the mounng locaon of screws on the
wall around the embedded pipe. Drill appropriate holes.
2. Insert the sensor cable and the tube/s into embedded pipe and lead them out
from the boom of reserved holes and then mount the spout on wall (use the
expand-screws if needed).
3. Tighten the decorave cover on the spout. Penetrate the spout through the xing board of decorave
wall and adjust its direcon and then fasten the nut.

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 5
[phone]
Free AU 1800 669 006
2.2 Installing the Control Box
1. Locate and mark the proposed locaon of the stainless steel bracket. The bracket must be installed horizontal.
2. Drill the proposed holes for the stainless steel bracket (Figure 2). Depth of hole: 25mm. Diameter of hole: 3mm without rub-
ber stopper / 7mm with rubber stopper.
3. Fix the bracket by self-tapping screws on the proposed locaon on wall (the screw stopper can be used with self-tapping
screws if needed).
4. Insert the hanging bracket that is on the back of the control box into the hanging hole of the bracket and push downwards.
2.3 Connecon of Parts
Figure 1 Figure 2
1. Connect the male end with female end of sensor cable.
2. Connect the soap tube on corresponding outlet.
3. Connect the male end with female end of power cable.

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 6
[phone]
Free AU 1800 669 006
2.4 Tesng for Use
Aer installaon, please test the product according to the following
instrucons:
1. Connect with power aer lling the soap into the bole.
2. Press the key switch unl the soap is sping from the nozzle
to prime the pump (Figure 1).
3. Put your hands under spout in appropriate distance (Figure
2).
4. Wait for soap to dispense in xed amount (Figure 3).
5. Watch for any leakage from the connecon point of the soap
tube. If this occurs gently push the connecng tube into the
outlet.
6. Do not places hands too close or directly beneath the sens-
ing range to avoid the soap splashing (Figure 4).
2.5 Rell or Replace Soap
If you have the foam dispenser, simply twist o the top cap and rell soap.
If you have the soap dispenser, follow steps below:
1. Twist o the soap bole 2. Rell the soap bole 3. Reconnect the bole with the control box
Figure 1
Figure 2 Figure 3 Figure 4

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 7
[phone]
Free AU 1800 669 006
3. Care and Cleaning
Light cleaning
Use a so cloth soaked with water to wash and dry the spout. Use the same cloth
when dry to wipe o any stains on the sensor cabinet.
For heavy-dirt cleaning
Please use the cloth soaked with right amount of neutral detergent to wipe o the
stain and then clean with water.
Please be careful when cleaning around the sensor cabinet to avoid scratching the
sensor.
Do not use the following to clean the product:
• Acid detergents, chlorine decolorizer, alkali detergent or detergents con-
taining abrasive grain, such as polishing powder.
• Solvents such as paint and the solvent covered benzene.
• Abrasive tools such as nylon brush/steel wool, etc.
Cleaning the nozzle and soap bole
Please use a so brush to clean the nozzle. Open by twisng. If the nozzle is blocked
use an Allen Wrench.
Cleaning the control box and soap bole
If there is block or back-ow occurs on the host, please wash the soap bole completely and then rell with clear water
into the bole, then press the key switch to clean the host. Follow the steps for Tesng For Use then repeat with soap.
3.1 Periodic Maintenance
Please check connecon points monthly for soap leakage and fasten connecon points accordingly every 6 months is required.
3.2 Long-term Suspension of Use
Please follow the below methods to undertake cleaning if the dispenser has not been used for a long me to clean out any
soap in the soap tube.
1. Remove any exisng soap in the bole and clean it out with water.
2. Rell the soap bole with clear water and complete the connecon to the control box.
3. Press the key switch unl the soap contained in the soap tube is pumped out completely.
4. Make sure the power is o and clean the soap bole thoroughly, dry it, then rell with soap.
5. Follow the steps in Tesng For Use.

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 8
[phone]
Free AU 1800 669 006
4. Diagram and Parts List
CAT 68931 Soap Dispenser
No. Part # Descripon No. Part # Descripon
1. 689-931 Dispenser Body
(Chrome)
8. 689-019 Soap Outlet
2. 689-007 Nozzle 9. 689-011 Control Box Bracket
3. 689-000 Sensor 10. 689-023 Key Switch
4. 689-010 Sensor Wire 11. 689-003-2Control Box
5. 689-021 Soap Tube 12. 689-003-1Soap Bole
6. 689-009 Sensor Plug 13. 689-004 6V Baery Box
7. 689-008 Power Plug 689-005 Power Adaptor
689-001 Remote Control
689-932 Dispenser Body
(San)
21
3
4
5
6
7
8
9
10
11
12
13

MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 9
[phone]
Free AU 1800 669 006
4. Diagram and Parts List
CAT 68932 Foam Dispenser
No. Part # Descripon No. Part # Descripon
1. 689-931 Dispenser Body 9. 689-008 Power Plug
2. 689-007 Nozzle 10. 689-023 Key Switch
3. 689-000 Sensor 11. 689-002-3Control Box
4. 689-010 Sensor Wire 12. 689-011 Control Box Bracket
5. 689-019 Soap Outlet 13. 689-002-1Foam Bole
6. 689-020 Air Outlet 14. 689-002-3Foam Bole Bracket
7. 689-021 Soap Tube 15. 689-004 6V Baery Box
8. 689-009 Sensor Plug 689-005 Power Adaptor
689-001 Remote Control
1
2
3
4
7
5
6
8
9
10
11
12
14
13
15