MeLaSen Electronics MLSH8 User manual

Model: MLSH8
ISED Certification No.:26807-MLSH8
FCC ID: 2AYGE-MLSH8
Manufacturer: MeLaSen Electronics Ltd.
Address:No.29 Industrial Road, Xiaolan Industrial Estate, Xiaolan Town, Zhongshan, 528415 Guangdong, P.R.
China
Install two 1.5V battery into the remote control. To prevent damage to
the remote control, remove the battery if not used for long periods of time.
3. Press and release the button, the light will turn ON and OFF accordingly.
8. Press the (2H/4H/8H) buttons to automatically turn the fan off after 2, 4 or 8 hours.
7. Press and release the button to change the light colour from warm light to white light.
4. Press +to increase speed and -to decrease speed. You can select fan speed 1-6.
2. Press and release the button, the fan will turn ON and OFF accordingly.
6. Press and release the button will activate the Comfort Breeze mode.
Alternates through speeds 1-5.
1. All ON/ OFF button.
BREEZE COLOR TEMP.
ON / OFF ON / OFF
6 SPEED BRIGHTNESS
TIMER
ALL
HR
2HR
4HR
8
5. Press +to increase brightness and -to decrease brightness.
2
4
6
1
3
5
7
8
LED light
REMOTE CONTROL OPERATING INSTRUCTIONS
□Install the remote control holder spacer onto the wall using two remote control
holder screws, and then attached the remote control holder onto the
spacer, ensure two parts fit together and no gaps, install the remote control
holder screws.
INSTALLING THE REMOTE CONTROL HOLDER
LEARNING PROCESS
Turn the main power source off to begin the learning process.
Return the power to the unit.
Within 3 seconds of turning the fan’s AC power ON, press and release
the button and then press and release the button to enter the
learning function. A beeping sound is emitted when pairing is complete.
Should you desire to use another remote control unit with your
new fan, install one using the steps below:
NOTE: After the AC power is on, do not press any other button
on the remote control before pressing the (ON/OFF) button.
Doing so will cause the procedure to fail.
□
□
□
spacer
WARNING: Do not short-circuit, disassemble, heat up,
connect improperly, or dispose of used batteries in fire. Do
not recharge or mix batteries with used or other battery
types. Immediately remove used batteries.
WARNING: a) The cells shall be disposed of properly,
including keeping them away from children; and
b) Even used cells may cause injury.
WARNING: Chemical Burn Hazard. Keep batteries away
from children. Always completely secure the battery
compartment. If the battery compartment does not close
securely, stop using the product, remove the batteries, and
keep it away from children. If you think batteries might have
been swallowed or placed inside any part of the body, seek
immediate medical attention.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’ s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitationestautorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible
d'encompromettre le fonctionnement.