Memco Panachrome User manual

1. Detector Installation
The Panachrome 43mm 3D/2D detectors can be tted to centre-opening or side-opening doors. For the visual indicators
to be eective, the system should only be installed in dynamic mode, with at least one of the detectors xed to a moving
door. TX detector must be tted to left side of lift when viewed from landing.
Memco Panachrome
2D/3D 43mm Prole
Installation Guide
Ref No. C540 850GB Version 1
Installation Notes - 3D
1. When installing a Panachrome 3D system, the following
precautions must be observed for trouble-free
operation:
2. Always mount the detectors as close to the door edge
as possible.
3. Sight-Guards cannot be used with Panachrome 3D
detectors.
4. For opening exceeding 1200mm, it is recommended
that ‘As Doors Close’ mode is used.
5. The detectors must be set no more than 10mm apart
when the doors are fully closed. The detectors must be
aligned to within +-8mm of the detector centreline.
6. 3D Switch Settings are detailed on the inside of the
Main Controller C3850 000.
2. To Remove Panachrome from xing L-Bracket
This is done by leveraging the main detector from the bracket attachment
Installation Notes - 2D/3D
1. The landing doors must not lead the car doors by more
than the suggested permissible amount as shown in Fig 1.
2. Screw the earth ring tag to the lift door using a No.8
screw and a shakeproof washer
3. The earth must be tted to ensure the unit is properly
grounded
4. Check also that the door itself is grounded to the lift
5. Use a P-clip either side of the pluggable connectors, to
reduce the risk of plug and socket separating
6. Do not shorten Memco cables by cutting them.
7. Detectors should be aligned as closely as possible for
reliable operation

3. Mounting Diagram
Centre opening doors with both detectors tted to the leading edge
Mounting Diagram
Side opening doors with RX detector tted to the slam
DOOR
ARM
TRAVELLING
CABLE
TRAVELLING
CABLE
5mm from sill
DOOR ARM
TRAVELLING
CABLE
5mm from sill

Step 5
Attach cable securely with the
P-clips and screws provided. Avoid
tight bends while providing enough
slack so that cables are not stressed
or stretched as the doors move.
Step 1
Using the correct mounting
bracket
Step 3
If L-Bracket is not tted then
position bracket ush
with underside of
cable end-cap and
progressively clip
detector into
bracket
Step 4
Secure L-Bracket to door using
screws provided. Locate screws
approximately 75mm from top
and bottom and equally space
remaining screws.
4. Step by Step Guide
Fitting detector to door (Centre-Opening)
4. Step by step guide
Fitting Detector to Door (Side Opening)
Step 5
Position underside of cable end cap
and ush with top of bracket. Clip
detector into bracket
Step 1
Using the correct mounting
bracket
Flat-Bracket for mounting
on Slampost or Leading
edge of door
Step 2
Do not t the Flat-Bracket to the
detector, rst position bottom of
Flat-Bracket on slampost 5mm
above car sill
Step 3
Remember to ensure the
detector will align exactly with the
detectors mounted on the door
when the door closes
Step 4
Secure the Flat-Bracket to
the slampost using the screws
provided. Ensure screws are
centred and evenly spaced along
length of bracket.
Step 2
Do not t the Flat-Bracket to the
detector, rst position bottom of
Flat-Bracket on slampost 5mm
above car sill
Door
Slam
5mm from sill
5mm from sill
AVIRE Ltd
Unit 1, The Switchback
Gardner Road
Maidenhead
Berkshire
SL6 7RJ, UK
T: 01628 540 100
F: 01628 621 947
E: [e-mail]
W: www.memco-global.com
W: www.avire-global.com
Memco is a brand of Avire
PA43 IG V01 (GB)