Memphis Shades MEB8975 User manual

2320-0033 MEMPHIS SLIMS MOUNTING KIT HD V-ROD
MOUNTING INSTRUCTIONS
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
No additional tools required for this kit.
1. Cover gas tank and front fender with a towel to avoid
damage during installation.
2. Install the two mounting plates onto the windshield, using
the bottom and third bolt up. Leave the nylon washers off.
The small tab goes to the bottom, big one at the top. Tabs
point out, away from the headlight. (see fig. 1)
3. Loosely install the four Fork Clamps on the forks, approxi-
mately 1" down from the upper triple tree and 1-3/4" apart.
(see figure 2)
4. Install headlight visor. With black side up, form visor
around headlight, smooth curve facing forward. Push it in
between the headlight bracket and headlight nacelle until the
ends firmly locate on the headlight bolts at both sides. (see
Fig.3)
5. Start with Fork Clamp Bushing adjusted to rear of slot (see
figure 2 and 3) Then adjust as needed and check for clear-
ance. (See warning above.)
6. Slip the windshield mounting plates and windshield onto
the fork clamps, (see figure 3 and 5) and secure the left and
right side locking mechanism
(CONTINUED)
7. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after
installing the windshield! (see figure 5)
Read and follow these directions carefully.
During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks
are turned all the way in either direction. Also make sure,
through the full range of adjustment, that the windshield and
hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Fig.1
Fig. 2
WARNING:
"Mounting clamps
backwards will cause
damage to your tank."
Throttle side,
front of bike
INCORRECT
Throttle side,
front of bike
CORRECT
Fig. 3
Form visor and
push it in until
it firmly locates
on the headlight
bolts.
MEM8975 08-13-08

2320-0033 MEMPHIS SLIMS MOUNTING KIT HD V-ROD
MOUNTING INSTRUCTIONS
2320-0033 FATS/SLIMS KIT
3
MEM8975 08-13-08
CORRECT
Fully engaged
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
12
3
Figure 5
4
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
QTY .
1
1
DESCRIPTION
3/16" SHORT ARM ALLEN WRENCH
3/16" ALLEN WRENCH COVER
PART #
M310
M313
PART #
M1172
M8975
R323
R318
M520
M306
DESCRIPTION
RIGHT MOUNTING PLATE FATS/SLIMS
MOUNTING INSTRUCTIONS/PARTS LIST
BUSHING ASSEMBLY (2 PART)
1" SOCKET SHOULDER WASHER
INNER ADJ. FORK CLAMP HALF
1/4" - 20 X 5/8" SOCKET HEAD CAP SCREW
QTY.
1
1
4
4
4
4
M1173 LEFT MOUNTING PLATE FATS/SLIMS 1
M533
MEDIUM OUTER DETACHABLE ADJ. FORK CLAMP HALF 4
M369 STAINLESS STEEL WASHER 4
M303 1/4" - 20 X 3/4" SOCKET HEAD CAP SCREW 4
R324 #207 EPDM 0-RING 4
R329 SLOT NUT 4
1. M533
2. M520
3. M1173
4. M1172
5. R310
2
1
BUSHING
ASSEMBLY
4
R322 C/T LATCH ASSEMBLY 2
R310 HEADLIGHT VISOR 1
BUSHING ASSEMBLY
A C
C
D
E
F
A. R329
B. M369
C. R323
D. R324
E. R318
F. M306
B
5
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us at
[email protected]