Memphis Shades 2320-0166 User manual

Part No. 2320-0166
Trigger-Lock Mounting Kit - Polished
Memphis Fats/Slim Windshield
HD XL 883L Super Low 2011 - 2014
Before assembly, read Warnings inside
MEK2001
WARNING
During installation, make sure that the fairing and
hardware do not interfere with any cables or wiring
when the forks are turned all the way in either direction.
Also make sure , through the full range of adjustment,
that the fairing and hardware do not hit the gas tank.
1.
2.
3.
This is a detachable fairing, ALWAYS make sure the
locking mechanism is fully engaged after installing the
fairing.
The improper installation of this kit and related
components could result in serious injury or death.
CAUTION
Memphis Shades fairings are made from Lucite
acrylic, and will last for years with proper care. Clean
your fairing with plenty of soapy water (mild dishwash-
ing liquid is best) and a soft cotton cloth. Use your bare
hands to feel and dislodge bugs, or cover with a wet,
soapy towel and let it soak. Don’t use paper towels and
scrape with anything. Small scratches can be removed
with NOVUS #2.
1.
Never use any glass cleaning products, petroleum
based chemicals, or cleaning agents with ammonia,
bleach or any other harsh chemicals. This includes (but
not limited to) RainX, brake fluid, acetone, paint thinner,
benzene and gasoline. “If it hurts your nose, it will hurt
the plastic.”
2.
Glass cleansing agents will cause severe damage to
your fairing, and will void your warranty.
For care and cleaning we recommend using Memphis
Shades All Kleer, a unique cleaner/polish, bug
remover and rain repellent that leaves a super slick
surface that makes the next cleaning even easier.
3.
Ref Code Description Qty
I2001 Mounting Instructions 1
M1607EC Clutch side mounting plate 1
M1608EC Throttle side mounting plate 1
S1215EC Small detachable clamp assembly 4
M310 Short arm allen wrench, 3/16 1
M314 T-Handle Wrench, 3/16 1
Memphis Shades warrants all product components, metal
and plastic, against defects in materials and workmanship
for 24 months.
For Parts and Warranty Help, Contact:
Memphis Shades, Inc.
P.O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or you
can also reach us by email:
[e-mail]
1. Kit Contents
2. Mounting Instructions
At certain times of the day the Sunlight can reflect off
the curvature of a fairing and cause extreme heat build-
up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an
opaque object over the instruments or adjust the fairing
to avoid reflections.
4.
REVISION 08052014
Aluminum parts are electrocoated (E-coated)
for durability and weather resistance.



Additional tools required that are not included in this kit.
7/16”(11mm), 1/2”(13mm), 9/16”(14mm) wrench & 3/4”(19mm)
socket.
1. Cover gas tank and front fender with towels to avoid
damage during installation.
2.Slide rubber boot off clutch cable adjuster - Located about
halfway along clutch cable by front frame downtube. (Fig. 1)
3. Holding the cable adjuster with a 1/2 in wrench, loosen jam
nut with a 9/16 in. wrench. Back jam nut away from cable ad-
juster. Move adjuster towards jam nut to allow free play at
hand lever.
4. Remove retaining ring from pivot pin groove at bottom of
clutch lever, and remove pivot pin. Remove clutch hand lever
from bracket.
5.Re-route the clutch cable to inside of handlebars (Fig. 2)
6. Reinstall clutch leaver, pivot pin and retaining ring, then turn
cable adjuster away from jam nut until slack is eliminated at
hand lever then tighten jam nut.


#memphisshades

Loosen Allen
Bolt to adjust
angle, then
re-tighten
Allen Bolt.
Space Approx.
2" apart.
WARNING:
Mounting clamps backwards
will cause damage to your tank.
Throttle side,
front of bike
INCORRECT
CORRECT
Adjust Fork Clamp as needed
and check for clearance. (See
above "Read and Follow
Directions Warning.")
Bushing Assembly
1. Place lower slot into lower bushing.
2. Rotate top slot into place.
3. Secure locking Mechanism.
4. Loosen Allen Bolt to adjust angle,
then re-tighten Allen Bolt.
1 2 3 4
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
Latch
assembly
7. Install the two mounting plates onto the windshield, using
the bottom and third bolt up. Leave the nylon washers off.
The small tab goes to the bottom, big one at the top. Tabs
point out away from the Headlight. (Fig. 3)
8. Loosely install the four Fork Clamps on the forks, approxi-
mately 2" apart. (Fig. 4)
9. Start with Fork Clamp Bushing adjusted to the rear of the
slot (Fig. 4 & 6) Then adjust as needed and check for clear-
ance. (See WARNING)
10. Slip the mounting plates and fairing onto the fork clamps,
(Fig. 5 & 7) and secure the left and right side locking mecha-
nism
11. Adjust the height, angle and alignment of the fairing and
tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield! (Fig 8)
2. Mounting Instructions, continued
Rubber boot
Cable adjuster
Jam nut
Cable end
Fig. 1
Re-route inside
Fig. 2
Fig. 3
Fig. 4
Fig. 6
Fig. 7
Fig. 8
Third bolt
First Bolt
Fig. 5
Fig. 9