Kuryakyn 1198 Service manual

CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[e-mail]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the
following provisions:
•Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
•The product must be properly installed,
maintained and operated under normal conditions.
•Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
•Küryakyn shall not be liable for any consequential
and incidental damages, including labor and
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in non-
conforming condition, or for any breech of contract
or duty between Küryakyn and a customer.
•Küryakyn products are often intended for use
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
•Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the con-
sumer. Components of Küryakyn products containing
L.E.D.s will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
•Küryakyn makes no warranty of any kind in
regard to other manufacturer’s products distributed
by Küryakyn. Küryakyn will pass on all warranties
made by the manufacturer and where possible, will
expedite the claim on behalf of the customer,
but ultimately, responsibility for disposition of the
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and
Metric Cruisers in our annual catalogs. Order
online today–select the ”CATALOGS” icon. Each
Küryakyn® product comes with a Proof-of-Purchase
good for a complimentary catalog. Details in
packaging.
Be sure to ask your local dealer about
other Küryakyn products, the motorcycle
parts and accessories designed for riders
by riders.
©2005 Küryakyn USA®All Rights reserved.
INSTALLATION
PARTS INCLUDED
1 Zombie Windshield Trim
1 Hardware Kit Including:
2 1/4” Flat Washer
1 1/4”-20 x 5/8 Socket Button Head Cap Screw (SBHCS)
2 1/4”-20 x .625” Knurled Spike Fasteners
2 1/4”-20 x 1” Knurled Spike Fasteners
1 Zombie Emblem
1 Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KÜRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY
AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION
TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES
REGARDING THE USE AND CARE OF THIS PRODUCT.
WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE
CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR
SERIOUS INJURY.
CAUTION! This indication alerts you to the fact that ignoring the contents described
herein can result in potential injury or material damage.
ATTENTION!This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
TOOLS SUGGESTED
Set of hex wrenches, Torx wrenches, combination wrenches
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE
THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS
ACCIDENTS.
NOTE; IF INSTALLING WINDSHIELD TRIM
ON KüRYAKYN® AIRMASTER™ FAIRING,
USE THE 1/4”-20 X 1” KNURLED SPIKE
FASTENERS.
PROCEDURE
STEP 1 Park the motorcycle on a hard, level surface;
turn off the ignition.
FITS: ’96-UP FLHT, FLHTC, FLHTCU, FLHX
1198-12HD-0209
ZOMBIE WINDSHIELD TRIM 1198
PIC.1
REMOVE THESE
THREE TORX
HEAD SCREWS

INSTALLATION
STEP 2 Remove the three Torx head screws that secure the windshield shown in PIC.1. Set these
aside, they will not be used again.
STEP 3 Place the trim in place, lining up the holes in the trim with the holes in the in the
windshield.
STEP 4 Place the 1/4”- 20 x 5/8” SBHCS screw in the center hole without a washer,
do not tighten.
STEP 5 Place the appropriate Knurled Spike Fasteners in the outside holes with
the ¼” flat washers as shown in PIC.2, do not tighten.
STEP 6 Tighten the screws, being careful not to over tighten them, which may
damage the trim.
STEP 7 Place the zombie emblem in place with head facing up as shown in PIC.3.
PAGE
2
ZOMBIE WINDSHIELD TRIM INSTALLATION
PIC.3
PIC.2
INSERT KNURLED
SPIKE FASTENER WITH
THE 1/4” WASHER