Memphis Shades MEM-8981 User manual

2321-0080 YAMAHAROAD STAR FATS/SLIMS MOUNTING KIT ’99—’08
MOUNTING INSTRUCTIONS
Read and follow these directions carefully.
During installation, make sure that the windshield and
hardware do not interfere with any cables or wiring when
the forks are turned all the way in either direction. Also
make sure, through the full range of adjustment, that the
windshield and hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
First Bolt
Third
Bolt
Figure 2Fig 1
Additional tools required that are not included in the kit.
7/16” or 11mm wrench, 10mm wrench and a blunt pry tool.
1. Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the two mounting plates on the windshield using the
bottom and third bolt up. Leave the nylon washers off. The
small tab goes to the bottom, big one to the top. Tabs point
out away from the headlight, (Fig-1).
3. Using a blunt tool carefully pry off the two bolt hole covers
on each side of the headlight, (Fig-2).
4. Use a 10mm wrench to remove the headlight bracket bolts
from the lower triple tree, (Fig-2).
5. Assemble a small L bracket onto the rear face of the Right
and Left brackets, (Fig-3). Do not tighten bolts at this time.
6. Locate the small L brackets over the remaining bolt in the
lower triple tree and secure in place using the original head-
light bracket bolts, (Fig-4). Do not tighten bolts at this time.
7. Complete the installation of the Right and Left bracket as-
semblies by using the exposed holes either side of the head-
light, (Fig-4). Fit the bolt through the washer, through the
bracket, through the spacer and into the triple tree. Confirm
the fit is good and tighten all bolts.
8. Install the windshield by placing the lower slots into the
lower mounting bushings. Slip the upper slots into the upper
mounting bushings and gently but firmly seat the slots into
place.
Lock the locking mechanism into place, (Fig-5)
9. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make re
the Locking Mechanism is Fully Engaged after installing
the windshield! (see figure 5)
Figure 3
MEM-8981 3/19/10

2321-0080 YAMAHAROAD STAR FATS/SLIMS MOUNTING KIT ’99—’08
MOUNTING INSTRUCTIONS
MEM8981 FATS/SLIMS KIT
Fig 4
MEM-8981 3/19/10
CORRECT
Fully engaged
NOT CORRECT
Fig 5
Part # Description Qty
M8981 Mounting Instructions 1
M1189 Left Mounting Plate, Fats / Slims 1
M1188 Right Mounting Plate, Fats / Slims 1
M1193 Left Road Star Bracket 1
M1192 Right Road Star Bracket 1
R318 1” Socket Shoulder Washer 4
R323 Bushing Assembly (2 part) 4
R324 #207 EPDM O Ring 4
M303 1/4”-20 x 3/4” Socket Head Cap Screw 4
M505 Button Nut 4
R321 1” Recessed Spacer Washer 4
M1195 Left Lower Bracket 1
M1194 Right Lower Bracket 1
R322C Clutch Side Latch Assembly 1
Part # Description Qty
R322T Throttle Side Latch Assembly 1
R334 6-32 x 3/8” Flat Head SS Screw 8
R326 SS Spring 2
M310 3/16” Short Arm Allen Wrench 1
M313 3/16” Allen Wrench Cover 1
R349 10mm x 20mm Button Head Cap Screw 2
R337 10mm SS Washer 2
R335 3/4” x 1/8” Upper Bolt Spacer 2
M302 1/4”-20 x 1/2” Socket Head Cap Screw 2
M501 Beveled Socket Washer 2
R329 Slot Nut 2
M311 6mm Short Arm Allen Wrench 1
M1307 5mm Long Arm Ball End Allen Wrench 1
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
You can also reach by email:
[email protected]
Remove headlight
bracket bolt and install
bracket with same bolt
View from back side of
forks (clutch side shown)
Bracket fits over this
bolt, no need to remove
1. Place lower slot into lower bushing.
2. Rotate top slot into place.
3. Secure locking Mechanism.
4. Loosen Allen Bolt to adjust angle, then re-tighten
allen bolt.
4
2 3
1