Memphis Xtreme Audio MXASB35 Limited Warranty
This product has a one year warranty from the date of purchase for defects in material or workmanship. This
warranty will be extended to 2 years when installed by a Memphis authorized dealer using Memphis Connection
products. The warranty is void if the product has been physically damaged by improper usage or abuse. If
repairs are attempted outside of a Memphis Audio facility, the warranty is void.
This warranty is limited to the original retail purchaser and does not cover any expenses incurred in the removal
or re-installation of the product. This warranty does NOT apply to product exterior and cosmetics. Memphis Audio
disclaims any liability for incidental or consequential damages caused by product defects. Memphis Audio liability
will not exceed the purchase price of the product and the warranty period specified.
What is NOT covered under warranty
• Damage due to improper installation
• Damage through negligence, misuse, accident or abuse. (Repeated returns for the same damage may be abuse)
• Product damaged in accident and/or due to criminal activity
• Service performed by anyone other than Memphis Audio
• Subsequent damage to other components
•Any cost or expense related to the removal or re-installation of product
• Products with tampered, missing , altered or defaced serial numbers/labels
• Freight damage
•The cost of shipping product to Memphis Audio
• Return shipping on non-defective items
•Any product not purchased from an authorized Memphis Audio dealer
Some states do not allow the exclusion or limitation of incidental or consequential damages. The above limitations
or exclusions may not apply to you. This warranty gives you specific rights, you may have other rights which vary
from state to state.
If warranty service is required, a return authorization number is required to return the product to Memphis Audio.
Warranty shipments to Memphis Audio are the responsibility of the purchaser. Pack the product carefully in the
original carton if possible Memphis Audio will not be responsible for damages incurred in shipment or due to
improper packaging materials used by the purchaser.
If determined to be within warranty your product will be repaired or replaced at the discretion of Memphis Audio.
For your safety, always inspect the mounting location carefully to ensure you are not drilling into any electrical,
hydraulic, fuel or fluid lines. Always check your speaker load with a multi-meter before connecting the amplifier.
Connecting any speaker load lower than the rated impedance of the amplifier will result in damage to the amplifier.
Damage of this nature is NOT covered under warranty. Please pay close attention to what connections are made to
the amplifier.
If you are uncertain or uncomfortable proceeding with your installation, please contact your local
Authorized Memphis Audio Dealer
No Output:
• Confirm all wiring is firmly connected.
Both +12V must have +12 Volts present and GND must be connected to chassis’ ground or to
the negative battery terminal.
• Confirm the signal source is connected via Bluetooth or the auxiliary cable is connected to both the source and the MXASB35
Weak Output
• Check Bluetooth device volume level.
Unwanted Noise
• Whine that increases and decreases with engine speed - confirm the Amp & Source unit are grounded properly.
• Clicking or popping noise at a rate that follows engine speed - this is often induced by the vehicles ignition system.
Confirm that the vehicle is equipped with resistor spark plugs and wires. The ignition system may need service.
• Noise can be caused by routing speaker input wires too close to the light wires and other accessory wires in the
vehicle. Re-route wires to avoid unwanted interference.
Red LED is Illuminated
• Speaker or wire is shorted • Battery voltage too low
• Battery voltage too high • Amplifier has overheated due to improper ventilation
If above steps do not improve/reduce noise, the system should be checked by a professional audio installer at a
Memphis Authorized Dealer.
•Take 14 mm bolt with lock washer and place it through bottom of clamp and slightly thread into Dove tailed piece.
• Slide assembly into one of the three dove tail recessed areas placing the unit at the desired angle.
•Tighten bolt to securely hold bracket in place.
• Repeat this step for both included brackets. Both brackets must be used during installation.
• Use bracket top half and tighten down over bar using the four included bolts, two per clamp.
•Tighten until the unit is secure.
• Connect wires to power, ground, and optional Aux-in our Audio out.
WARRANTY
WARNING
MOUNTING
TROUBLESHOOTING
