Menvier Security TS400 Operation manual

TS400 & TS410
Installation & User Guide
Compatible Equipment
TS400 REM - Remote Keypad
9040 - Loudspeaker
SD1+ - Speech Dialler
496522 Issue A 1of10 TS400 & TS410

Overview
Introduction
The TS400 and TS410 are 6 zone microprocessor based
intruder alarm control panels with 5 programmable
zones and a dedicated Final Exit zone. The ease of
operation for setting and unsetting lends itself ideally to
domestic and smaller commercial installations.
TS400 Features
l5 Programmable zones Night, Access, Fire, PA &
Keyswitch (plus common tamper)
lDedicated Final Exit zone
lOn board keypad and LED indicators
lUp to 4 remote keypads
lFacilities to connect to an SD1+ Speech Dialler
l4 event log
lProgrammable output for vibration detectors or
latching PIRs
lDual user codes
lRemote Reset facility
l2.1 Ah battery capacity
lAll data stored in Non-Volatile Memory (NVM)
TS410 Features
l5 Programmable zones Night, Access, Fire, PA &
Keyswitch (plus common tamper)
lDedicated Final Exit zone
lBlind control panel supplied with 1 remote keypad
with the option to support up to 4.
lFacilities to connect to an SD1+ Speech Dialler
l4 event log
lProgrammable output for vibration detectors or
latching PIRs
lDual user codes
lRemote Reset facility
l7.0 Ah battery capacity
lAll data stored in Non-Volatile Memory (NVM)
Specifications
TS400 Control Panel
Input Voltage: 240V ±10% 50Hz
Current: 40mA (normal) 85mA (alarm)
Power Supply: 750mA
Standby Battery: 2.1Ah
Dimensions: 205 (W) x 205 (H) x 64 (D) mm
Material: 3mm polycarbonate
Weight: 1.2 Kg
Environment: 0 - 55°C
TS410 Control Panel
Input Voltage: 240V ±10% 50Hz
Current: 40mA (normal) 85mA (alarm)
Power Supply: 750mA
Standby Battery: 7.0Ah
Dimensions: 242 (W) x 237 (H) x 86 (D) mm
Material: 1.2mm mild steel
Weight: 2.6 Kg
Environment: 0 - 55°C
Remote Keypad
Current: 35mA (normal) 50mA (alarm)
Dimensions: 130 (W) x 130 (H) x 30 (D) mm
Material: 3mm polycarbonate
Weight: 415g
Environment: 0 - 55°C
TS400 & TS410 2of10 496522 Issue A
TS400 & TS410

System Installation
PCB Layout
Bell Fuse
This 1 Amp fuse protects the supply to the external
sounder/bell.
Aux Fuse
This 1 Amp fuse protects the supply to devices power
from the auxiliary 12V terminals.
Speaker Volume R37
Cut R37 to reduce the volume of the extension
loudspeakers.
Factory Restart Pins
If these pins are shorted during power-up all system
programming data is restored to the factory default
values, see page 6 for defaults.
Home Inhibit Link
Whenthelinkisopenthe(Alm-)terminalactivates when
analarmoccursduringafullorpartsetcondition.When
the link is closed the [ALM-] terminal activates only if an
alarm occurs during a full set condition.
Zones1-5Indicator LEDs
These red indicator LEDs indicate the alarm status of
zone1-5.Note these are not fitted on the TS410.
Unset Indicator LED
ThisgreenindicatorLEDisusedtoindicatethestatusof
the system set or unset. It also flashes when the mains
power is removed or when the user selects the user
program mode.
Tamp Indicator LED
ThisredLEDisusedtoindicateasystemtamperalarm,
it also flashes when the engineer program mode is
selected. Note this is not fitted on the TS410.
F/E Indicator LED
ThisredLEDisusedtoindicatethestatusofthefinalexit
zone. Note this is not fitted on the TS410.
496522 Issue A 3of10 TS400 & TS410
TS400 & TS410
A.C.
ALM
-
RST
-
TRG
-
STB
-
+H/O-TMP
-
AUX
TAMPER
L/S
-
AUX 12V
+-
P. A .
ZONE 5
FIRE
ZONE 4
K'SW
ZONE 3
ACCESS
ZONE 2
ACCESS
ZONE 1 F/EXIT
Remote Keypad
Interface Connector
Keypad
(Not fitted on TS410)
Factory Restart Pins
Indicator LEDs
Home alarm
inhibit link
C
ut R
3
7toreduce
volume
(1AMP)
AUX 12V
Leads to
transformer
Tamper switch
Zone
connections
External
sounder
connections
Bell (1AMP)
123
456
789
HOME 0AWAY
FACTORY
RESTART
VOLUME R37
HOME ALM
INHIBIT
12
UNSET TAMP F/E
345
EXTERNAL BELL
Figure 1. TS400 & TS410 Connection Diagram

Wiring Example
TS400 & TS410 4of10 496522 Issue A
TS400 & TS410
ALARM
Supply +
Supply -
SMOKE DETECTOR
TAMPER
0V
+12V
PIR
TAMPER
ALARM
0V
+12V
PIR
To AUX +12V
To AUX -12V
To ZONE 4 (FIRE)
P. A . B U T T ON
To ZONE 5 (P.A.)
FLUSH CONTACT
SURFACE CONTACT
To FINAL EXIT
To ZONE 3
To AUX -12V
To AUX +12V
To ZONE 2
To AUX -12V
To AUX +12V
To ZONE 1
TRIGGER -
STROBE -
HOLD OFF +
HOLD OFF -
TAMPER RETURN -
EXTERNAL SOUNDER ALM -
RST -
TRG -
STB -
+
-H/O
TMP -
AUX
TAMPER
L/S -
+
-AUX 12V
ZONE 5 (P A)
ZONE 4 (FIRE)
ZONE 3 (K/Sw)
ZONE 2 (ACCESS)
ZONE 1 (ACCESS)
FINAL EXIT
TS400/TS410
NOTE:
Any unused zones must be
linked out.
PIRs and Surface Contacts may
be connected to any zone. This
diagram is only used to represent
a typical installation example.
If a keyswitch is fitted, it must be
connected to Zone 3 and then
programmed as KEYSWITCH.
If a Smoke/Heat Detector is fitted,
it must be connected to Zone 4
and then programmed as FIRE.
If a P.A. Button is fitted, it must be
connected to Zone 5 and then
programmed as P.A.
= 16 Ohm Extension Loud speaker
(cut R37 to reduce volume)
TERMINAL STRIP
(NOT SUPPLIED)
R37
ALARM
Figure 2 Example Wiring Diagram

Installing a Remote Keypad
Ensure that the mains and battery power has been
disconnected and proceed as follows:
1. Connect each core of the 6-core cable to the
interface terminals "LEDCBA"(make a note of the
colours used for each connection).
2. Pass the yellow flying-lead behind the PCB and
connect it to the [L/S-] terminal.
3. Plug the Interface board into the interface socket as
shown below:
4. Separate the remote keypad cover and base by
using a screwdriver to push two of the clips (top or
bottom) inwards from the cover retaining slots. Then
lift the cover assembly, noting that the circuit board
is connected to the under side of the cover.
5. Holdtheremotekeypad base in position (keyholeto
the top) and mark the three securing holes, drill and
plug the wall as required. Pass the 6-core cable into
the base via the cable entry points as appropriate
and secure the base to the wall.
6. Connect each core of the 6-core cable to the
remote keypad terminals "LABCDE",ensuring that
the connections through to the control panel are A
to A, B to B, etc. If more remote keypads are to be
fitted, they may be connected in a star or daisy
chain configuration (providing the cable length to
the last or furthest remote keypad does not exceed
50 metres).
7. Carefully reattach the front cover assembly to the
remote keypad base ensuring that all cables are
clear of the tamper switch spring and the cover is
securely clipped to the base.
Extension Loudspeakers
A 16 Ohm extension loudspeaker can be connected
between the [L/S-] and [AUX 12V+] terminals. R37
(locatedinthetoplefthandcornerofthePCB)canbe
cut to reduce the volume of the internal sounders
(alarm is always full volume).
ALM- Terminal
This terminal is switched negative (100mA) on alarm
and is removed when the system is reset. If the Link
marked "HOME ALARM INHIBIT" on the main PCB is
closed, the [ALM-] output is disabled when the system
is part-set (Home). Normally this output is used to
trigger a speech dialler or similar.
RST- Terminal
This terminal may be programmed as:
Detector Reset (DTR RST)
WhenprogrammedasDetectorResettheoutputmay
be used for detectors which latch their alarm
condition, and must be de-powered to reset (e.g.
smoke detectors, vibration detectors etc.). Power for
such detectors must be connected between [AUX
12V] and [RST-].
Switched 12V (SW12V)
When programmed as Switched 12V the output may
be connected to the latch input terminal on latching
detectors (e.g., PIRs etc.). This feature is normally used
when more than one detector is connected to a
single zone. It allows the user to identify the alarm
source by latching the indicator LED on the detector
that caused the alarm activation. The latched LED will
clear when the system is reset.
496522 Issue A 5of10 TS400 & TS410
TS400 & TS410
InterfacePCB
Flying-lead
connectedtoL/S-
Flying-lead
L/S
Figure 3 Remote Interface Connections
16 Ohm Loudspeaker L/S -
AUX +12V
Figure 4 Speaker Connections

Aux 12V Power
The auxiliary 12V terminals provide a permanent 12V
supply for detectors which require a low voltage supply
e.g., PIRs, vibration detectors, smoke detectors etc. The
output is protected by a 1 Amp fuse (Aux 12V).
The maximum available current from the control panel
power supply is 750mA. The following is a typical
example showing how to calculate the available
auxiliary current.
Control Panel = 85mA
External Sounder = 250mA
External Strobe = 115mA
Total =450mA
Auxiliary Available = 300mA (750 - 450)
SD1+ (Optional)
The SD1+ is a customer programmable speech dialler
which dials pre-programmed numbers to inform
neighboursetc.ofthealarm.Itiscapableoftransmitting
up to 3 messages linked to inputs A, B and C.
Initial Power-Up
1. Place a small screwdriver blade between the pins
on the control panel PCB, marked FACTORY RESTART
(located just below the LEDs). This will ensure the
factory defaults are loaded as shown below:
Engineer Code 1234
User Code 1 5678
Zone 1 Alarm
Zone 2 Access
Zone 3 Alarm
Zone 4 Alarm
Zone 5 Alarm
Exit Time 30 Seconds
Entry Time 30 Seconds
Bell Duration 20 Minutes
Bell Output SAB (-ve applied)
Remote Reset Number 004
Setting Mode Timed Set
Reset Authority User Reset
Number Of Rearms 3
Operation Of Keyswitch Away Set (Full)
RST- Output Detector Reset
HOME Set Configuration Zone 1 Omitted
Factory Default Settings
2. Switch on the 240V mains supply, when the green
UNSET LED is lit remove the screwdriver blade. The
internal alarm will sound and the TAMPER LED will
light.
3. Enter the engineer’s passcode (default1234),
the alarm will silence. Enter the engineer’s
passcode again and the TAMPER LED will flash
(engineer programming menu selected).
4. Connect the standby battery. If the TAMPER LED
lights permanently and the internal alarm sounds
when the battery is connected, then it may be
incorrectly connected or it may be totally
discharged. Disconnect the battery immediately
and reconnect or replace as appropriate.
5. Push the battery into place at the bottom of the
housing and re-fit the front cover.
☞On the TS410 you MUST connect the earth
bonding cable from the front cover to the
spade connection point.
6. Fit the battery link in the external sounder and
replace cover.
7. The system is now ready for programming.
TS400 & TS410 6of10 496522 Issue A
TS400 & TS410
ALM -
RST -
TRG -
STB-
+
-
TMP -
AUX
TAMPER
L/S -
+
-
ZONE 5 (P A)
H/O
AUX 12V
ZONE 4 (Fire)
TRIG A
TRIG B
0V
+12V
TAMPER
BOX
TRIG C
Set TRIG POLARITY to -ve
Note: Only connect TRIG A (FIRE)
and TRIG B (PA) if zones 4 and 5
are programmed as Fire and PA.
TS400/TS410 SD
1+
Figure 5. SD1+ Connections Details

Key Functions
Engineer’s Reset
1. Enter the Engineer’s Code default 1234. You
are now in Engineer’s Mode.
2. Press 0to return to unset.
Loading Defaults
1. Power down panel mains and battery.
2. Place a small screwdriver blade between the
pins on the control panel PCB, marked Factory
Restart.
3. Power up panel battery and mains.
4. Remove screwdriver.
5. Enter 1234 to silence alarm.
6. The system will have reverted back to Factory
Default Programming.
Bell Test/ Walk Test
Please refer to user’s menu numbers 1 and 2
respectively.
496522 Issue A 7of10 TS400 & TS410
TS400 & TS410

Engineer’s Quick Reference Programming Chart
TS400 & TS410 8 of 10 496522 Issue A
TS400 & TS410
Key Function Action LEDs On Off
1 Zone Types Press [1] - [5] to toggle LEDs on/off.
Press [0] to end
1
2
3
4
5
Z1 = Access
Z2=Access
Z3 = Keyswitch
Z4 = Fire
Z5=PA
Z1 = Alarm
Z2 = Alarm
Z3 = Alarm
Z4 = Alarm
Z5=Alarm
2 View Log Press [1] for newest event
Press [4] for oldest event Zone LEDs that light have caused an alarm
3 Walk Test Activate detectors.
Press [0] to end When the zone is in alarm the panel will sound and the relevant zone LED will light.
4 Exit Time Press [1] to [4].
Press [0] to end
1
2
3
4
10 seconds
30 seconds
1 minute
2 minutes
5 Entry Time Press [1] to [4].
Press [0] to end
1
2
3
4
10 seconds
30 seconds
1 minute
2 minutes
6 Bell Duration Press [1] - [5].
Press [0] to end
1
2
3
4
5
90 seconds
3 minutes
10 minutes
20 minutes
Continuous
7Change Engineer's
Passcode Enter new passcode twice Zone LEDs1-4will light, as code is entered each LED will go out one by one.
8 Remote Reset No. Enter reset number twice Zone LEDs1-3will light, as code is entered
each LED will go out one by one.
9 System Options Press [1] - [6] to toggle LEDs
on/off
Press [0] to end
1
2
3
4
5
F.Exit
Bell output = SAB
Set by Final Exit
Reset by Engineer
3 re-arms
Key = Home set
RST = SW12V
Bell output = SCB
Set by Timed Exit
Reset by User
1 re-arm
Key = Away set
RST = Det. Reset
HOME Part set the system Leave via exit route
AWAY Full set the system Leave via exit route
0 Return to unset
Engineer's Quick Reference Programming Chart

User Options Menu
496522 Issue A 9of10 TS400 & TS410
TS400 & TS410
Unset
LED
Flashes
1
2
4
6
7
0
HOME
HOME
=BellTest
=WalkTest
= Change Passcode 1
= Change Passcode 2
= Home Set Configuration
= Return to unset mode
Press twice when the system
is in the unset mode to select
"Chime" zones.
123 4 5
TAMPERUNSET FINAL EXIT
12345
TAMPERUNSET FINAL EXIT
HOME
5 6 7
E
nter first 3 digits of passcode then
(e.g., )

TS400 & TS410 10 of 10 496522 Issue A
TS400 & TS410
This page intentionally left blank