Menvier Security SD1 Manual

SD1+
Speech / Auto Dialler
OPERATION & MAINTENANCE MANUAL
SD1+
Speech / Auto Dialler
OPERATION & MAINTENANCE MANUAL

Contents
Getting Started: SD1+ Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Passcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Passcode Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Programmable Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Call Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Call Abort. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Last Call Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Acknowledgement Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Telephone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Recording Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Deleting Phrases & Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Playing Back Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Sending a Test Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Three Way Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Programming: Initialising The SD1+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Changing Your Passcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Changing Your Passcode Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Programmable Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Call Routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Abort Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Viewing The Last Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Acknowledgement Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming: Telephone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Forcing The SD1+ to Tone / Pulse Dial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming a Pause into the Telephone Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Programming a Pager Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Recording Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Deleting Phrases & Telephone Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Testing the SD1+: Call Acknowledgement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Playing Back Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Sending A Test Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General: Three Way Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Trouble-Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Quick Reference: Dialler Options.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Quick Reference: Advanced Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Getting Started: SD1+ Menu Options
All of the SD1+ menu options are accessed by entering the user
passcode (default 1234). These menu options allow all the
necessary programming of the SD1+ and are selected by
pressing the relative "Hot Key" as shown in the table below. A
summary of menu options and their relative "Hot Key" is also shown
to the right.
1
Hot Key Menu Option Page
1Not Used
2Not Used
3Not Used
4Change Passcode 4
5Change The Passcode Type 5
6Programmable Output 5
7Call Routing 6
8Abort Options 6
9Viewing The Last Call Log 7
0Acknowledgement Options 7
[1-4Program Phone Number 1, 2, 3 or 4 8 - 11
[0-DRecord Phrase 0, A, B, C or D 12
[[ Delete Phrases & Phone Numbers 13
ABC or DPlayback Messages A, B, C or D 14
A1-4
B1-4
C1-4
D1 -4
Send Message A, B, C or D to
Telephone Number 1, 2, 3 or 4
15
READY
SD1+
OUTPUT-
ROUTE-
ABORT-
ERASE-
VIEWLOG-
CLEARBY-
NEWCODE-
4
????
C,TYPE-
5
6
7
8
[[
9
0
Change passcode
Change Code Type
Program Output
Call Routing
Abort Options
Delete Options
View Event Log
Acknowledgement
[
Replay Message's
A, B, C or D
Send To Phone
No's 1, 2, 3 or 4
ABC
Dor
1-4 / ENT
TO SEND
ENT 1-4
OR 0-D
Enter Phone Numbers
or Record Messages

The SD1+ is connected between the leak
detection alarm panel and the telephone
line. It behaves like another extension to the
telephone and does not affect the normal
operation or that of any other extensions
fitted. However, if the SD1+ is operating, and
any telephone handset is lifted, the
messages will be heard. The unit is powered
by a 12v dc mains adaptor supplied as an
option.
The SD1+ can accept up to four inputs which
in our example are; A - Leak Detected,
B - Cable Break, C - Service Required and
D - Auxiliary. These inputs correspond to
messages (A, B, C or D) that the SD1+ sends
out and should be recorded as such. The
SD1+ can also accept a direct connection
from suitable auxiliary devices such as an
optical probe, float switch or anything using
volt free contacts.
Overview
Connections
Passcode
Passcode Type
Programmable Output
Call Routing
2
This product is manufactured to meet all European Economic Area Tele-communication networks requirements.
The SD1+ requires a passcode to be entered
to gain access to all of the programming
menus, this code can also be used to
cancel an activation if the unit has been
accidentally triggered. See page 4.
The passcode that is required by the SD1+
to enter into the programming menus, can
be modified so that it is either a standard 4
digit code, or a 6 digit code. See page 5.
The SD1+ has a programmable output that
is capable of supplying up to 100mA of
current. This output can be programmed to
activate when the SD1+ has been triggered,
when the SD1+ has been successfully
acknowledged, or when the SD1+ has failed
to communicate to all telephone numbers.
See page 5.
The SD1+ can be programmed so that each
trigger input A, B, C or D will only dial a
certain telephone number. This can be used
for when the dialler is required to call four
different numbers under three different
conditions e.g. trigger A will only dial
telephone number 1, trigger B will only dial
telephone numbers 2 & 3 whereas trigger C
will dial telephone numbers 1,
2, 3 & 4. See page 6.
A, B, C & D
Auxiliary
Inputs

Call Abort
Last Call Log
Acknowledgement Options
Telephone Numbers
Recording Messages
Deleting Phrases & Numbers
Playing Back Messages
Sending a Test Call
Three Way Calling
3
The SD1+ can be programmed so that if it
is accidentally triggered, the call can be
aborted. Once aborted, the dialler will
stop dialling out immediately. The SD1+
can be aborted by one of the following
methods: when a signal is applied to the
abort input, when the input that triggered
the unit is removed, or when the user
passcode is entered. When an abort is
performed by the code, the display
shows as visual confirmation of
the abort being carried out (a chime
tone will also be heard). See page 6.
The SD1+ has a last call log, this enables
the user to find out who the unit has
dialled and who acknowledged it. The
log also shows which input was triggered
last. See page 7.
Once the SD1+ has made its call and
delivered its message, it requires a signal
to say that the message has been
successfully received. This is done by the
recipient pressing the number "8" button
on their telephone. See page 14. When
the SD1+ has been acknowledged, it will
shut down until it is triggered again. This
option determines how many times the
unit must be acknowledged before it
shuts down. See page 7.
The SD1+ can dial up to four different
telephone numbers. These numbers can
be up to 24 digits long and are
programmed using the LCD display and
keypad on the unit. The numbers can be
forced to tone or pulse dial if required and
a pause can also be programmed. It is also
possible for the SD1+ to dial a pager and
send a numerical message, this message
is programmed by the user (a digit is also
sent after the message that corresponds to
the trigger input e.g. 1, 2,3 or 4
= Trigger A, B, C or D). See pages 8-11.
The SD1+ has a built-in microphone so that
phrases can be recorded directly into the
unit. The message that is sent by the SD1+
consists of a common phrase (0) which
normally states your name & address, followed
by phrase A, B, C or D which relate to the
inputs applied from the control panel (Leak
Cable Break or Service Required in our
example). The SD1+ has up to 40 seconds of
recording time which has to be shared by all
4 phrases. It must be noted that if 10 seconds
is initially used by phrase 0 and you need to
re-record that phrase, 10 seconds must be
used by the new phrase 0. See page 12.
Because the SD1+ has a Non Volatile
Memory (NVM), the phone numbers and
messages cannot be deleted by removing
power from the unit. This option, allows you
to delete all phrases or all phone numbers
as required. See page 13.
Once the phrases have been recorded by
the SD1+, they can be played back through
the on board speaker so that you can check
the recorded message. It should be noted
that when you play back phrases A, B, Cor
D, phrase 0 is always played first.
See page 14.
Once the SD1+ has been programmed,
each message can be sent to a particular
number to test whether the unit is working
correctly. When the unit is in this test mode,
everything on the phone line will be heard
through the speaker. The display will also
give a visual indication of what is happening
during the call. See page 15.
This is a service that is normally provided by
British Telecom, if this service is enabled, the
SD1+ will use it to prevent anyone trying to
block the telephone line. See page 16.

Programming: Initialising The SD1+
When you power up the SD1+ for the first time, a factory restart is
required. This involves shorting out the factory restart pins (JP2) whilst
applying power to the unit (please refer to the installation
instructions for details). The display will show “ ”, this
indicates that the memory is blank (i.e., all telephone numbers and
messages are not programmed). Once it is programmed, " "is
displayed instead. To gain access to the programming menus, the
passcode must be entered (Default 1234).
1. When the unit is powered up for the very first time, the display
shows “ ”.
+
When programmed, the display shows “ ” (fig 2).
2. Enter the default user code 1234 to initialise the unit ready
for programming.
3. When initialised the display shows “ ”, the unit can now be
programmed and tested.
+
To exit from the main menu press , if the unit is not
operated for 1 minute, it will revert back to the “
” message (or “ ”, fig 2).
Changing Your Passcode
The SD1+ requires a passcode to be entered to allow access to the
program menus, this passcode can also be used to abort the
operation of the unit when triggered (see page 6). The passcode is
normally four digits, but can be changed to six (see page 5). The
default passcode is 1234 and can also be changed as required.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press 4and the display will show “ ”.
3. Press [and the display will show “ ”.
4. Enter your new passcode e.g. 2580.
5. Press [to accept the new code and return to “ ”.
4
3
NEWCODE-
READY
READY
2580
1
4
2
5
SD1+
----
????
2580
4
[
[
SD1+
READY
1
3
2
SD1+
????
]
Fig 2
READY
1
3
2
RECORD
RECORD
PLEASE
PLEASE
????
]
Fig 1

Changing Your Passcode Type
The SD1+ requires a passcode to be entered to allow access to the
program menus. This passcode is normally 4 digits ( ), but
can be changed to 6 digits ( ). The default user passcode is
1234. If the passcode is changed from 4 to 6 digits, the last two
digits of the code will default to (00) i.e. 1234 will now become 1234
00.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press 5and the display will show “ ”.
3. Press [and the display will show the code type option that is
currently programmed i.e. “ ”.
+
Scroll through the other 3 passcode options “
”, “ ” and “ ”, by pressing the
key.
+
Note: Do not use the following passcode types: 4 digits
followed by enter ( ), or 6 digits followed by
enter ( ). These are reserved for future use
4. Press [to accept the option displayed and return to “ ”.
Programmable Output
The SD1+ has an output that can be programmed to activate
under certain conditions. These conditions are: active when the
SD1+ has been triggered ( ), active when the SD1+ has been
acknowledged ( ) and, active when the SD1+ has dialled
all numbers and has not been acknowledged ( ).
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4)”.
2. Press 6and the display will show “ ”.
3. Press [and the display will show the output type that is currently
programmed i.e. “ ”.
+
If required, the other 2 output types “ ”, and
"" can be scrolled through by pressing the key.
4. Press [to accept the option displayed and return to “ ”.
5
6 Digit Code
3
C,TYPE-
READY
1
2
4
3
SD1+
????
4, CODE
6, CODE
4+E, CODE
6+E, CODE
5
READY
[
[
B
B
B
4 Digit Code
4 Digit Code + ENT
6 Digit Code + ENT
3
OUTPUT-
READY
1
2
4
3
SD1+
????
ACTIVE
SUCCESS
FAILED
6
READY
[
[
B
B
Has Been Triggered
Has Been Acknowledged
Failed to Communicate

Call Routing
Messages A, B, C or D can be programmed so that they only report
to certain telephone numbers i.e. Message A might report to
telephone numbers 1, 3 & 4 but NOT to number 2 ( ).
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press 7and the display will show “ ”.
3. Press [and the display will show that message A is routed to
telephone number s 1, 2, 3 & 4 i.e. “ ”.
+
Press 1, 2, 3 or 4 to select or deselect the telephone
numbers.
+
If required, the other 3 options “ ”,“ ”&“
”, can be scrolled through by pressing the key.
4. Press [to accept the option displayed and return to “ ”.
Abort Options
Occasionally you may trigger your alarm by accident and cause
the SD1+ to send an unwanted call. When this happens the unit
can be stopped, by applying a signal to the abort input on the
SD1+ ( ), removing the trigger from the SD1+ ( ) or,
simply entering your user passcode ( ).
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press 8and the display will show “ ”.
3. Press [and the display will show the abort option that is
currently programmed i.e. “ ”.
+
If required, the other 3 abort options “ ”, “ ”
and “ ”, can be scrolled through by pressing
the key.
+
If the abort option is set for anything other than “ ”,
then the abort input becomes trigger “D”.
4. Press [to accept the option displayed and return to “ ”.
6
3
ROUTE-
READY
1
2
4
3
SD1+
????
A) 1234
B) 1234
C) 1234
D) 1234
7
READY
[
[
B
B
B
SendAtoNo's1,2,3or4
SendBtoNo's1,2,3or4
SendCtoNo's1,2,3or4
SendDtoNo's1,2,3or4
Restore The Alarm Input
3
ABORT-
READY
1
2
4
3
SD1+
????
NONE
RESTORE
INPUT
PASSCODE
8
READY
[
[
B
B
B
No Abort Available
Abort Input
Abort With Passcode

Viewing The Last Call Log
When a call is successfully acknowledged, the SD1+ stores the
event in a “Last Call Log”.
The log may then be viewed as follows:
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press 9and the display will show “ ”.
3. Press [and the display will show the Last Call Log i.e. " "if
the log is empty, or ” ” (Alarm on trigger input A
acknowledged by recipient 3). If the display shows “ ”
then none of the calls were acknowledged.
4. Press [to accept the option displayed and return to “ ”.
Acknowledgement Options
Once the SD1+ has made its call and delivered its message, it
requires a signal to say that the message has been successfully
received. This is done by the recipient pressing the number "8"
button on their telephone. When the SD1+ has been
acknowledged, it will shut down until it is triggered again. This option
determines how many times the unit must be acknowledged
before it shuts down. These options include: Any 1 person ( ),
Any 2 people ( ), Any 3 people ( ), All 4 people ( )
or nobody at all ( ).
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press 0and the display will show “ ”.
3. Press [and the display will show the acknowledgement option
that is currently programmed i.e. “ ”.
+
If required, the other 4 acknowledgement options
"ANY-2”, “ ”, “ ” and “ ”, can be
scrolled through by pressing the key.
4. Press [to accept the option displayed and return to “ ”.
7
3
VIEWLOG-
READY
1
2
4
3
SD1+
????
BLANK
A) --3-
9
READY
[
[
B
No Events Logged
Last Message Sent(A to Tel 3)
3
CLRBY-
READY
1
2
4
3
SD1+
????
ANY - 1
ANY - 2
ANY - 3
ANY - 4
NO-ONE
0
READY
[
[
B
B
B
B
Needs 1 Acknowledgement
Needs 2 Acknowledgements
Needs 3 Acknowledgements
Needs 4 Acknowledgements
Needs No Acknowledgement

Programming: Telephone Numbers
The SD1+ stores up to four telephone numbers, with a maximum of 24 digits each. Permission from
the person(s) being called must be obtained before storing their telephone number. The SD1+
must NOT be used to call the Police via the Emergency Services telephone numbers.
The following example shows how to program telephone number 1 as 0181 234 5678.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press [, the unit will display “ ”.
3. Press 1for telephone number 1.
+
1 to 4 will select numbers 1, 2, 3 or 4.
+
0 to D selects phrases 0, A, B, C or D (see page 12).
4. The display will alternate between telephone No. 1 and the
current number (Blank if it has not been programmed).
+
If a telephone number is already programmed, this may
be deleted by pressing the key.
5. Type in the first phone number 0181 234 5678.
6. If a mistake is made whilst entering the number, press Ato
move the cursor back, re-enter the digit and press C.
+
Pressing will move the cursor forward again.
7. Finish typing in the telephone number and press [.
8. Repeat for telephone number 2, 3 & 4 as required.
9. When finished, press ]to return to the ready prompt.
+
In order for the SD1+ to comply with BABT regulations, the
unit must NOT have any telephone numbers programmed
the same.
+
The SD1+ must NOT be used to call the Police via the
Emergency Services telephone numbers.
8
1
2
43
OR 0-D
[
TEL NO 1
3
6
018153*
BLANK
1
5018153
AA
7
0181 3*
8ENT 1-4
018123*
OR 0-D
9
READY
]
45678[
2C
READY
SD1+
????
ENT 1-4

Forcing The SD1+ to Tone / Pulse Dial
Pulse Dialling: This is the older format and is sometimes referred to as Loop Disconnect/LD. Tone
Dialling: This is the modern format and sometimes referred to as Multiple Frequency/MF. Any or all of
the telephone numbers can be selected to override the automatic format selection and be
forced into dialling the number in one of the above formats if required.
Before entering the telephone number 0181 234 5678 in the example below, press the Bkey to
select “Pulse Dialling” ( ) or press the Ckey to select “Tone Dialling” ( ).
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press [and the unit will display “ ”.
3. Press 1for telephone number 1.
+
1 to 4 will select numbers 1, 2, 3 or 4.
+
0 to D selects phrases 0, A, B, C or D (see page 12).
4. The display will alternate between telephone No. 1 and the
current number (Blank if it has not been programmed).
+
If a telephone number is already programmed, this may
be deleted by pressing the key.
5. Press the Bkey once to select “Pulse Dialling” ( ).
+
Pressing the key will select “Tone Dialling” ( ).
6. Type in the first phone number 0181 234 5678 and press [.
7. Repeat for telephone number 2, 3 & 4 as required.
8. When finished, press ]to return to the ready prompt.
+
If the SD1+ is NOT forced to pulse or tone dial, it will
automatically select the correct dialling format.
9
1
2
43
OR 0-D
[
TEL NO 1
3
6
P*
BLANK
1
5B
018112
345678
7ENT 1-4
2345678*
OR 0-D
8
READY
]
[
READY
SD1+
????
ENT 1-4

Programming a Pause into the Telephone Number
If the SD1+ is connected to an internal PABX telephone exchange, a prefix digit i.e. 9 is normally
required before an outside line can be obtained. Some exchanges also require a pause after this
digit before dialling the telephone number. If required one or more 3 second pauses can be
inserted after the prefix digit.
Before entering the telephone number 0181 234 5678 in the example below, press 9for the dial
out prefix, then press the Bkey three times to select a 3 second Pause.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press [and the unit will display “ ”.
3. Press 1for telephone number 1.
+
1 to 4 will select telephone numbers 1, 2, 3 or 4.
+
0 to D selects phrases 0, A, B, C or D (see page 12).
4. The display will alternate between telephone No. 1 and the
current number (Blank if it has not been programmed).
+
If a telephone number is already programmed, this may
be deleted by pressing the key.
5. Press 9(or your own prefix), and then Bthree times to select a
pause, then press Cto move the cursor forward again.
+
A pause is displayed as a comma (,).
6. The SD1+ will now show (or your own prefix) on the display.
7. Type in the first phone number 0181 234 5678 and press [.
8. Repeat for telephone number 2, 3 & 4 as required.
9. When finished, press ]to return to the ready prompt.
+
The pause option ( ) will cause the SD1+ to wait 3 seconds
before dialling the rest of the telephone number.
Programming two ( ) or three ( ) pause options will cause
the SD1+ to pause 6 or 9 seconds.
10
1
2
43
OR 0-C
[
TEL NO 1
3
6
9,*
BLANK
1
59BBBC
018112
345678
7ENT 1-4
2345678*
OR 0-C
8
READY
]
[
READY
SD1+
????
ENT 1-4

Programming a Pager Number
When dialling a pager SD1+may have to wait before sending the message. To insert a pause enter
“” after the pager number. When the call is answered, the unit can send the message as normal or
precede it with a “star” or “hash”. This is achieved by programming ( ), ( )or( )
respectively. The pager message is ALWAYS terminated with a “hash”.
Note: Each pager service has its own requirements for pauses, star and hash. You may have to
experiment to find the correct combination for the service you are using.
After entering the pager number 0832 345678 in the example below, press Bfour times for the
pager prefix " ", then Cand enter the paging message i.e. 333, then
press [.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press [and the unit will display “ ”.
3. Press 1for telephone number 1.
+
1 to 4 will select telephone numbers 1, 2, 3 or 4.
+
0 to D selects phrases 0, A, B, C or D (see page 12).
4. The display will alternate between telephone No. 1 and the
current number (Blank if it has not been programmed).
+
If a telephone number is already programmed, this may
be deleted by pressing the key.
5. Type in the pager number e.g. 0832 345678.
6. Press Bfour times to select the pager option ( ), then press C.
7. Type in the paging message i.e. 333 for alarm, then press [.
+
Anything entered after the " ", is used as the message.
+
A digit relating to the input is also sent e.g. 1 = Trigger A.
+
8. The display shows how the message is sent " ".
+
If required, the other 2 options “ ” and “ ”,
can be scrolled through by pressing the key.
9. Repeat for telephone number 2, 3 & 4 as required.
10.
When finished, press ]to return to the ready prompt.
11
1
2
43
OR 0-D
[
TEL NO 1
3
6
BLANK
1
50832
345678
7
ENT 1-4
678M333*
M+NONE
345678M*
2345678*
OR 0-D
8
9
10 READY
]
[
333
[
BBBBC
READY
SD1+
????
ENT 1-4
PHONES
B

Recording Messages
The SD1+ can record up to four phrases A, B, C, D and a common phrase 0. These phrases can be
up to forty seconds in total. The five phrases are used to form four messages A, B, C and D. Phrase 0
is normally used to store the name and address of the premises, whereas phrases A, B, C or D are
used to store the type of alarm condition. It is also advisable to include the instruction to press the
number "8" button on the telephone, at the end of the message e.g.
lPhrase 0: “This Is Mr Smith, at 10 The Strand, East Fincham”
lPhrase A: “The alarm has been activated, please press eight to acknowledge this call”.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press [and the unit will display “ ”.
3. Press 0for phrase 0.
+
0 to D will select phrases 0, A, B, C or D.
+
1 to 4 selects numbers 1, 2, 3 or 4 (see pages 8-11).
4. The display will show “ ”.
+
Stand back about 6-8 inches from the unit.
+
Before you record phrases, it is advisable to prepare
them by writing them down first.
5. When ready, press the [key to start recording, and speak
clearly into the unit.
+
The display will show the remaining recording time.
+
When re-recording a phrase, if the duration of the old
phrase was previously 10 seconds, then the new phrase
must be the same length.
6. To end recording at any time press .
+
The unit will also stop recording when the time runs out.
7. Repeat for phrases A, B, C & D as required.
8. When finished, press ]to return to the ready prompt.
12
1
2
43
OR 0-D
[
RECORD
3
6
PHRASE 0
0
5[
7
REC - 40
REC - 32
8
ENT 1-4
OR 0-D
READY
]
]
READY
SD1+
????
ENT 1-4
This is Mr Smith,
at 10 The Strand,
East Fincham.

Deleting Phrases & Telephone Numbers
If new phrases need to be recorded or new telephone numbers need to be programmed into the
unit, the old ones will have to be deleted, this option will allow you to perform either of these actions.
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press [and the display will show “ ”.
3. Press [and the display will show “ ”.
4. Press Band the display will show “ ”.
+
If required, the other delete option “ ”, can be
scrolled to by pressing the key.
5. Press [to accept the option displayed and return to “ ”
+
If required, the telephone numbers can also be deleted
individually when in the telephone number programming,
(pages 8-10).
13
ENT 1-4
OR 0-D
READY
1
2
SD1+
????
[
3
3
[
B
Clear Messages
4
5
SPEECH
ERASE-
PHONES
READY
[
BClear Numbers

Testing the SD1+: Call Acknowledgement Procedure
If the unit has been triggered or a test call has been sent, you must
ensure that the recipient of the call is aware of the call
acknowledgement procedure, so that they can successfully shut
down the SD1+ and prevent it from dialling them again.
1. When the recipient's telephone rings, they should answer the
call as they would any normal call.
2. The SD1+ will then play the message that corresponds to the
trigger it has received, (normally the name and address of the
premises followed by the relevant alarm message).
3. After the message, a tone is heard, the recipient should now
press the “8” button on the telephone to acknowledge the call.
+
Pressing the number “8” button on the telephone at any
point during the message, will also shut the unit down.
4. If done correctly, an acknowledgement “tune” will be heard.
5. The recipient can then take the necessary action.
Playing Back Messages
Once the phrases have been recorded it is possible to play them
back through the built in loudspeaker.
This example shows how to play back “Message A” (Phrase0+A):
1. Ensure that the SD1+ is initialised and the display is showing
“” (see page 4).
2. Press Aand the display will show “ ”.
+
Pressing or will select message B, C or D.
3. After a 5 second delay the message is played.
4. Pressing ]at any point during the message will abort the
playback and return the unit to the “ ” prompt.
+
Repeat for message B, C or D, as required.
14
1-4 / ENT
TO SEND
READY
1
2
SD1+
????
A
3
3
5 Seconds
4
PHRASE 0
PHRASE A
READY
]
#
98
456
21
7
0
*
This is Mr Smith,
at 10 The Strand,
East Fincham.
1
2
3
4

General: Three Way Calling
Three Way Calling is a feature that is available from BT Network Services. For the SD1+ to take
advantage of this facility, the telephone line must have this service enabled (contact BT for details).
When the SD1+ is triggered, the unit checks for "dial tone", if no dial tone is detected i.e. another
telephone is "Off Hook" or there is an incoming call. The unit then sends a "Recall" signal, which is
detected by the exchange as a request for a new line. With a new line available, the SD1+ then
attempts to dial out.
+
If the SD1+ is connected to an older pulse dial exchange, the numbers being dialled must
be selected to pulse dial (see page 9). This will also disable the three way calling facility as
this is not available on the older exchanges.
Display Messages
When the unit is first powered up, a factory restart is required (page 4).
The SD1+ will then have a completely blank memory (no phone
numbers or messages programmed), program these as required. If
the unit is showing this display, and a factory restart has not been
carried out, contact your installation company for further advice.
This is the normal standby display of the SD1+ speech dialler. The unit
will display this message whilst it is doing nothing AND whilst it is dialling
out after it has been triggered.
The SD1+ has detected a ringing signal. This display will only be seen
during a test call and NOT an activation.
The recipient may already be on another call, wait until they have
finished the call and try again. This display will only be seen during a
test call and NOT an activation.
The SD1+ has detected an Unobtainable or Special Information Tone.
Check the number and try again.This display will only be seen during
a test call and NOT an activation.
The SD1+ dialled out, sent the message and was acknowledged
correctly by the recipient. This display will only be seen during a test
call and NOT an activation.
The call was not answered or acknowledged by the recipient. This
display will only be seen during a test call and NOT an activation.
If the SD1+ is programmed to dial a pager number, this message will
be displayed when the pager message is sent. This display will only
be seen during a test call and NOT an activation.
The SD1+ was aborted by a user passcode whilst it was attempting to
dial out following an activation. This display will only be seen
following an activation.
16
PLEASE
RECORD
SD1+
RINGING
ENGAGED
UNOBTAIN
SENT OK
NO REPLY
PAGED
ABORTED

Trouble-Shooting Guide
Problem
The recipient has acknowledged the call
but the SD1+ continues to dial the second,
third or forth number.
Cause
The "Call Acknowledgement" option is set to
cleared by " "or" "or" "
(page 7).
Action
Check the option is set to the required setting.
Problem
The unit will not dial the telephone number
that is programmed into the unit.
Cause
Number incorrectly dialled.
Action
Check the telephone number you are calling
has been entered correctly.
Cause 2
The SD1+ is dialling out through an internal
telephone exchange (PABX), that requires a
pause after the initial “9”.
Action 2
Make sure you have programmed a pause
into the phone number, after the "9" (page 10).
Cause 3
The SD1+ is wired to an exchange, that needs
a special button pressed to select a line.
Action 3
The unit cannot be used with this type of
exchange. Connect it to a standard BT line.
Problem
The unit is triggered from the Control Panel but
the display shows " " all the time.
Cause
The SD1+ doesn't display anything except for
"" whilst it is triggered.
Action
To see the status of the SD1+ when triggered,
use the “Test Call" option (page 15).
Problem
The recipient of the call can't acknowledge
the unit by pressing the number "8" button.
Cause
Incompatible telephone.
Action
Call the recipient and ask them to press the
number "8" button on their telephone. If you
hear anything other than a tone, the telephone
is not capable of acknowledging the SD1+. This
may be overcome by using a tone pad to
simulate the dialling tones. Contact your
installation company for details.
Problem
I am pressing the [key for 6 seconds, but I
cannot get to the " " prompt and the
display still shows " "or" ".
Cause
The SD1+ requires a 4 digit passcode to enable
you to gain access to the program menu's.
Action
Enter your user passcode (page 4).
17