Meraki Jenny User manual

ASSEMBLY SHEET
JENNY
version 1.0


42
54
22
6
8
4
8
1
1
1
8
8
2
2
Jenny B e d P a g e 2 o f 13
No. of People: 2 NO power tools
required.
Time: 2 hours Use a damp
cloth to clean.
ASSEMBLY INSTRUCTIONS
Please do not use a power tool to assemble this product. Using one may hinder
and/or damage the item and will invalidate any claims for warranty.
Depending on the amount of use this product receives, it may be recommended to
tighten up the fixings from time to time. This is completely normal!
Do not drag the bed. Always lift with at least two people to avoid injury or
damage.
A few important things to note:
PARTS INVENTORY
A
B
C
D
E
F
G
H
ID DESCRIPTION QTY
PARTS INVENTORY
I
J
K
L
M
N
ID DESCRIPTION QTY
PROTECTIVE PAD
PROTECTIVE PAD
M8*40 BOLT
14
OM8*25 BOLT
M8*65 BOLT
FLAT WASHER M6
SPRING WASHER
FLAT WASHER M8
NUT
M6*10 BOLT
ALLEN KEY
OPEN SPANNER
Level of
difficulty: 3/4
MATTRESS STOPPER
GAS LIFT RIBBON
GAP NUT


Thank you for making a purchase with Meraki Imports.
The goal of this assembly sheet
is to help you assembl
e the product in a way that will contribute to its longevity and
durability. Kindly follow all the instructions carefully to ensure a safe and accurate
assembly process.

Jenny B e d P a g e 3 o f 13
1
1
1
1
2
1
1
2
45
30
30
PARTS INVENTORY
1
2
3
4
5
6
7
8
9
10
11
ID DESCRIPTION QTY
2
2
2
4
1
1
1
1
1
2
PARTS INVENTORY
12
13
14
15
16
17
18
19
20
21
ID DESCRIPTION QTY
Headboard
Footboard
Left Hydraulic
Right Hydraulic
Gas Lift
Left Side Rail
Right Side Rail
Wood Slat
Single Close Ended Clip
Double Open-Ended Clip
Right and Left Metal Frame
Up and Down Metal Frame
Side Rail Connecter
Center Frame
Center Floating Leg
Corner Bracket
Footboard Middle
Bracket
Left Headboard Wing
Right Headboard Wing
Bottom Non-woven
Cloth
Headboard Back
Non-woven Cloth

Jenny B e d P a g e 4 o f 13
STEP 1
C
G
C
G
12
12
11
11
Step 1 : Attach parts 11 and 12 using hardware C and G.
C
G
!
!
: Pay attention to
these three holes on
the right and left metal
frame (11). They should
be facing the same
side.

Jenny B e d P a g e 5 o f 13
STEP 3
STEP 2
Once the frame has been assembled keep it aside.
We will be using it again in Step 12.
EE
A
EE
AA
F
14
14
A
F
!
A
A
15
14 14 E
E
F
F
!
Step 2 : Attach part 14 to both sides of part 12, using hardware
A, E and F.
Step 3: Attach the support
legs (15) to the holes
in part 14 as shown in
the photo, using
hardware A, E and F.

Jenny B e d P a g e 6 o f
13
20
21
E
H
A
1
STEP 5
34
5
5
The nut should only be tightened by hand and will not go all
the way in. No tools needed.
STEP 4
!
Step 4: Attach parts 20 and 21 to the
headboard using hardware
parts H, A and E.
Turn it upside down for more
ease.
Step 5: Unscrew the nut on the left and right
hydraulics (3 and 4) and attach the
gas lifts (5). Screw the nut back on.
We will now refer to this as the "gas
lift mechanism".

Jenny B e d P a g e 7 o f
13
STEP 7
3
7
4
6
N
E
19
J
O2
E
A
Step 6: Attach the gas lift
mechanism (3 and 4)
to the side rails 6
and 7 using
hardware N, E and A.
Step 7: Attach brackets (19) to footboard
(2) using hardware O and E.
!stick the felts(J) on top of the
bracket
STEP 6
!
!

Jenny B e d P a g e 8 o f
13
STEP 8
STEP 9
6
7
2
EDA
6
7
2
E
O
J
17
Step 9: Attach the corner bracket (17) to connect the side rails (6 and 7) to the
footboard (2), using hardware E and O .
!stick the felts(J) on top of the
bracket
!
!
Step 8: Attach the side rails (6 and 7) to the footboard (2), using hardware E, D
and A.

Jenny B e d P a g e 9 o f
13
B
13
6
7
2
B
B
E
O
O
13
STEP 10
STEP11
B
Step 10: Attach side rail connector (13) to the side rails (6 and 7) and head-
board (1) using parts B and E.
!
!
Step 11: Attach the second side rail connector (13) to the centre of both
side rails (6 and 7) using hardware O.
1

Jenny B e d P a g e 10 o f 13
E
F
F
JJ
M M
F
AA
E
A
E
Step 12: Attach the frame that you built in the previous steps to the gas
lift mechanism at a 45° angle (meaning it should be slanted as shown in
the picture) using hardware A, E and F.
!
STEP 12
!Stick the felts (J and M) on top of
the metal bar.

Jenny B e d P a g e
11 o f 13
DO NOT
PUSH DOWN ON ONE
OR EITHER SIDE
STEP 13 ONCE THE MATTRESS IS ON TOP,YOU CAN
OPEN & CLOSE THE BED SAFELY
Step 13:
Once all the nuts and bolts are tightened firmly, the first time
you close the lifting mechanism, push down with extra
pressure to force open the seals on the pistons.
This will feel like a lot of pressure, so be firm and it will close!
PUSH DOWN FROM
THE MIDDLE USING
BOTH HANDS

8
8L
10
9
Jenny B e d P a g e
12 o f 13
Step 14(a): Attach the slats (8) to the plastic clips and insert them into the
holes of the metal bars (11 and 14). Clips open from both sides (10) will be
attached to the middle bar (14), and clips open from one side (9) will be
attached to the side bars (11).
Step 14(b): Attach part K to the part 12.
Step 14(c): Attach the gas lift ribbon (L) to the metal frame (12) by making
a knot.
K
STEP14
14
11
12

Jenny B e d P a g e
13 o f 13
18
16
STEP15
Step 15a
Step 15b
:
:
Attach the non-woven fabric (18) to the bed. Start from the
bottom of the bed and go halfway behind the headboard.
Attach the non-woven fabric (16) to the
NOTE:The gaslift function works when you have a mattress on it. If you
don’t have a mattress on it, there is possibility it will not stay down.
back of the headboard.