Furniture Solutions 17RHOHE User manual

Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- [e-mail]
INSTRUCTION MANUAL
RHONE RECLINER CHAIR & FOOTSTOOL
ITEM CODE: 17RHOHE
117RHOHE
=Furniture Solutions =

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
217RHOHE
30
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2

PARTS LIST
317RHOHE

417RHOHE
ASSEMBLY INSTRUCTIONS
Please prepare work area as instructed in page 2:
To assemble Footstool:
Identify required hardware before you start assembly. Note do not over tighten any bolts,
tighten only till firm.
Take footstool base [6] & LWood [5] line up holes, then with bolt & washer (A) insert thru hole
then by hand turn bolt (A) 2-3 times to seat thread correctly, repeat for second bolt (A), once
both seated tighten with tool (G). Repeat for next LWood. Note ensure LWoods are facing same
direction.
Next turn footstool cushion [4] upside down as shown in diagram, insert bracket [B] into LWood
as shown in diagram. Line up slots on bracket [B] with hole in footstool cushion [4] place bolt &
washers [C] into hole and by hand turn 2-3 times to seat bolt (C) into thread correctly. Repeat
for other side. Once both bolts (C) are seated correctly, take tool [I] and tighten until firm.
Footstool complete. Note slots in bracket [B] allow for some adjustment to keep LWoods
square.

517RHOHE
ASSEMBLY INSTRUCTIONS
To Assemble Chair, attach backrest [2]
Take chair base with cushion [1] place in upright position as shown in diagram, with the help
of second person, bring backrest [2] to chair base [1].
Located at base of backrest & back of seat there are black metal tubes that have holes, you
may have to peel back fabric covering to locate. While second person holds back rest level as
depicted in diagram, so bolts [D] can be inserted and seated into thread provided, then by
hand seat both bolts [D] to ensure not to cross thread. Once both seated correctly tighten
with tool [G] tighten till you feel resistance, do not over tighten.
Please see diagram and remove black packaging from behind glide handle.

617RHOHE
ASSEMBLY INSTRUCTIONS
To Assemble Chair, attach backrest [2]
Now attach upper section of back rest to back of black bracket as shown in diagram, again
second person required to keep backrest square while fitting bolts [E]. By hand start bolt (E)
thru hole in bracket into backrest [2] again you may have to peel back leather covering to
locate threaded hole. Once both seated correctly take tool [G] and tighten bolts.
Note these bolts [E] are used as a pivot point for backrest movement and do not need to be
tighten flat against metal.
To attach Armrest: Place armrest [3] as indicated in diagram, aline holes in armrest [3] with
holes on bracket. Using bolt [F] insert bolt thru hole in bracket and into armrest (3) then by
hand seat bolt properly 2-3 turn, do not tighten until both bolts are fitted by hand. Once both
seated use tool (F) to tighten. Repeat for other side.

717RHOHE
ASSEMBLY COMPLETE

817RHOHE
FEATURE’S AND OPERATING OF RECLINER
FEATURE:
Twin glide handle locking.
The locking mechanism is design for variable recline positions, so you can find the right spot
for you to sit.
Please view diagrams below for operation of the glide handle system.

917RHOHE
FEATURE’S AND OPERATING OF RECLINER
FEATURE:
Adjustable head rest.
Internal adjustable headrest for variable use.
Please view diagrams below for operation of the adjustable headrest.

10 17RHOHE
FEATURE’S AND OPERATING OF RECLINER
FEATURE:
Swivel base.
Complete 360 degree turning circle.
FEATURE:
Adjustable tension on glide handle.
The glide handle can be customised to suit the individual.
Please follow step by step instructions below if you require to alter tension on glide handle