Mercura GYROLED M80 Guide

12/10/2018
ISO OR POLE MOUNTING M80 GYROLED®
GT-0693-FEUX Ind A
Siège social/Head-quarters : Zone d’Activités « Les Gailletrous » - rue Louis Pasteur- 41260 LA CHAUSSEE SAINT VICTOR –FRANCE -
Tel : [phone] –Fax [phone]
SAS au capital de 102. 400 € - APE (NAF) 2790 Z –SIRET 310 999 891 00040
Page 1
30656-00
CHARACTERISTICS
Power supply : 10 –30 Volts
Power : maximum 11W
Average consumption: 900mA depending on
operating mode / 850mA in rotating mode at 13.5
volts.
Maximum consumption : 5 Amps at peak
Operating Temperature : -40°C à +85°C
R65 approval available only with blue M80 GYROLED®
and amber M80 GYROLED®.
R65 marking :
Flashing Blue: TB1 E2 0016309
Rotating Blue : TB1 E2 0016311
Flashing Amber : TA1 E2 0016312
Rotating Amber : TA1 E2 0016310
EMC approval :
« E2 10R05 16242 » CISPR25 (2008)
R10 "E" Marking Regulation: class 4 or
5 class radiating.
1. 3 POINT ISO M80 GYROLED®
2. PROTECTIVE SEAL
3. 2 x PRODUCT MANUALS (1xFR et 1x GB)
4. 6 LOBE TCB M5x20 STAINLESS SCREW (x3)
5. M80 GYROLED® WIRING (x1)
1. POLE MOUNTING M80 GYROLED®
2. 2 x PRODUCT MANUALS (1xFR et 1x GB)

12/10/2018
ISO OR POLE MOUNTING M80 GYROLED®
GT-0693-FEUX Ind A
Siège social/Head-quarters : Zone d’Activités « Les Gailletrous » - rue Louis Pasteur- 41260 LA CHAUSSEE SAINT VICTOR –FRANCE -
Tel : [phone] –Fax [phone]
SAS au capital de 102. 400 € - APE (NAF) 2790 Z –SIRET 310 999 891 00040
Page 2
30656-00
RECOMMENDATIONS
The M80 GYROLED® installation on the vehicle should be done in compliance with the
specific current regulations regarding emergency and service vehicles special lighting.
The beacon flash pattern choice must also meet these requirements.
The installer is therefore fully responsible for the product installation and flash pattern
chosen.
The choice of the GYROLED® M80 position on a roof vehicle must meet regulation requirements on light
signalling installation.
M80 GYROLED® Standard positioning LEDs are identified from
1 to 8 (Upper view).
A. VEHICLE FRONT
B. VEHICLE REAR
C. OPERATING MODE SELECTION SENSOR INDEX
D. VENT HOLE
It is also important to ensure that M80 GYROLED® is mounted more than 30 cm away from a radio or
phone device (Transceiver, cables, antennas, filters).
INSTALLATION
3 POINT ISO MOUNTING
Use protective seal as template if necessary

12/10/2018
ISO OR POLE MOUNTING M80 GYROLED®
GT-0693-FEUX Ind A
Siège social/Head-quarters : Zone d’Activités « Les Gailletrous » - rue Louis Pasteur- 41260 LA CHAUSSEE SAINT VICTOR –FRANCE -
Tel : [phone] –Fax [phone]
SAS au capital de 102. 400 € - APE (NAF) 2790 Z –SIRET 310 999 891 00040
Page 3
30656-00
The wiring loom passage from the GYROLED® through to the vehicle interior must be
absolutely waterproof.
The use of an impermeable seal is recommended.
Ø78 ISO MOUNTING
A. M80 GYROLED®
B. PROTECTIVE SEAL
C. VEHICLE ROOF
D. FIXING SCREWS*
E. POWER SUPPLY WIRING
*Torque screws to 2Nm maximum
POLE MOUNTING

12/10/2018
ISO OR POLE MOUNTING M80 GYROLED®
GT-0693-FEUX Ind A
Siège social/Head-quarters : Zone d’Activités « Les Gailletrous » - rue Louis Pasteur- 41260 LA CHAUSSEE SAINT VICTOR –FRANCE -
Tel : [phone] –Fax [phone]
SAS au capital de 102. 400 € - APE (NAF) 2790 Z –SIRET 310 999 891 00040
Page 4
30656-00
WIRING AND FLASH PATTERN SELECTION
13 Flash patterns are integrated in the M80 GYROLED®. The operating mode setting must only be chosen
when the M80 GYROLED® is on and using a mobile magnet (not supplied). The operation consists in
moving the magnet in front a position located between the reference index and the fixing hole on its right.
A. MOBILE MAGNET (NOT SUPPLIED)
B. M80 GYROLED®
C. REFERENCE INDEX
D. FIXING HOLE
E. N°2 POWER SUPPLY WIRE
F. GYROLED® SWITCH (NOT SUPPLIED)
G. PROTECTION FUSE* (NOT SUPPLIED)
H. N°1 GROUND WIRE
AVAILABLE FLASH PATTERNS
1. R65 Rotating
2. R65 Double Flashing
3. Triple Flashing
4. Simple Flashing
5. ½ Rotating
6. ½ Double Flashing
7. ½ Triple Flashing
8. ½ Single Flashing
9. ICAO Flashing
10. ICAO Rotating
11. ½ ICAO Flashing
12. ½ ICAO Rotating
13. N°1 Led and n°8 Led 1Hz / 50% Flashing
Do not stare directly at the GYROLED®during operation, so as to avoid eye damage.