Groz LED 602 User manual

INSTRUCTION MANUAL
S2850, REV A
1
LED 602
LED 30W SMD
Site Lamp
30W SMD Site lamp with
aluminium die cast housing
in premium powder coated
finish
Portable powder coated
free-standing steel stand
with cushion grip &
adjustable stainless steel
bracket
Powerful 30W SMD with a
light output of 2100 lumens
Power Source:
220V AC, 50 Hz. & 110V
AC, 60 Hz.
Complete with 4m (13.12 ft)
long power cord
Water & Dust Proof
Rating: IP65 (Dust Tight
& protected from low
pressure jets from any
directions)
Ideal for portable working
in maintenance, building
construction, temporary
lighting jobs etc.
CAT NR. ORD NR.
LED/602/US 55075
LED/602/EU 55069
110V AC
220V AC
POWER
SOURCE
LUMEN
2100
IP65
WATER & DUST
PROOF RATING
−20°C TO 45°C
(−4°F TO 113°F)
OPERATING TEMPERATURE BEAM ANGLE
120°
ROHS

www.groz-tools.com
2
SAFETY INFORMATION
• Please read the instructions carefully to
ensure that the installation is done in the
correct manner. In addition, this manual
should be properly kept for future reference.
• This site lamp must be earthed.
• Always secure wires in plug terminals
carefully. Make sure the cable is firmly
located in the cord grip.
• Never connect the green & yellow wire to
any terminal other than one marked with the
earth symbol.
• Regularly inspect all electrical connections
and wiring for damage. Any faults should be
immediately rectified before further use of
this site lamp.
• In use, ensure all wiring and extension cables
are kept clear of any cutting tools, sharp
objects and any other potential hazard such
as wet floors, chemicals, solvents etc.
Note: If your main wiring diers in any way,
consult a qualified electrician. Always ensure
that the mains supply voltage is correct.
• Always replace the fuse with one of an
identical rating.
• The lighting direction can not be adjusted to
downward direction.
• Don’t touch the hot surface by hand during
adjustment and normal operation because of
high temperature.
• Don’t stand very close to the light while it is
switched on.
• Don’t look at the bulbs directly with naked
eyes.
• Don’t use the item without glasses and grills
replace any cracked protective shield.
• The bulbs can’t exceed the rated power.
• The distance between the item and any
object must be more than 1m.
PACKAGING CONTENT
NOMENCLATURE
INSTALLATION (REFER “NOMENCLATURE”)
Wire installation
1. Unscrew the junction box cover and remove
diuser and rubber seal.
2. Put your mains cable into the junction box
through the plastic stud and rubber gasket
ensure that the plastic stud is suciently
tight.
3. Connect the mains wire.
4. Replace the junction cover , take care not to
lose the rubber gasket on the cover.
LIGHT INSTALLATION
1. Slide the stand(E) into this site lamp bracket
(F) .
2. Align the holes in the bracket and the stand.
Insert and tighten angle adjustment screw
knob (D) .
3. To alter the angle of this site lamp, simply
loosen the angle adjustment screw knob(D) ,
pivot this site lamp until the desired angle is
achieved and re-tighten knob (D).
4. Check this site lamp are secure and that the
stand is stable and has a firm footing.
DISPOSAL
The components or the used products must
be given to companies that specialize in the
disposal and recycling of industrial waste.
DESCRIPTION QUANTITY
Light 1
S Stand 1
Easy Connect Wire 1
APadded Carry Handle
BPortable tube
CLuminous panel
DLamp body fixing frame
EAngle Adjustment Screw Knob
FS Stand
A
C
D
B
F
E

3

Groz Engineering Tools (P) Ltd.
Groz Net Industries
Village Kherki Daula, National Highway-8,
Gurugram-122001, Haryana, INDIA
Tel [phone]
Fax [phone]
E-Mail [e-mail]
Url www.groz-tools.com
The GROZ name, GROZ logo and the mark are
trademarks of Groz Engineering Tools (P) Ltd., India