visplay Xero Twin P/L User manual

play it smart
XeroTwinP/L
Assembly and operating instructions
USA & CANADA

2
General Instructions
1/2019 (US)
Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning, installation
and/or use of our products must be carefully read
and observe these instructions of use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports with
anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding 200 mm/
7.874" must be subjected to abrasive cleaning using
detergents specifically developed for this purpose. The
cleaning agents developed for abrasive cleaning contain
very finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.
Copyright
This manual is protected by copyright. Its use is
permissible as part of the use of the product. Any use
other than this is not permitted without written consent of
the manufacturer.
Our General Terms and Conditions apply for all orders.
www.visplay.com | [e-mail]
Dimensions are generally shown in millimeters and
inches.

3
Xero Twin P/L
34
9-060.19
34
9-061.19
red
6.1
0.240"
4.2
0.165"
349-140.19 (90 W)
NV (24 V)
L = 500 mm / 19.685"
ø 7.7 mm
0.303"
120 V
L =1500 mm / 59.055“
1/2019 (US)
Xero Twin P/L has a CE label and a UL certificate for U.S. and Canada.
Converter 24 V for electrified profile
Converter with input voltage 120–240 V / mains frequency: 50–60Hz electronic protection
against overload, overheating and short-circuit.
- Housing temperature max. 75°C / max. 167 °F
- Nominal output voltage: 24V / SELV
- Power supply with permissible nominal current of max. 4A
- Connection cable from converter to infeed unit 500 mm/19.685"
- Class 2
NOTICE! If dimmers are to be used, electronically controlled, low-voltage dimmers must be
installed!
TECHNICAL DATA SHEET XEROTWINP/L
XeroTwinP/L electrification in detail: conductor rail with power supply, integrated into system support profile.
Correct functioning and safety are guaranteed when properly used. No liability is accepted in event of improper use. Product safety
is based exclusively on the use of original XeroTwinP/L accessories from Visplay.
No alterations may be made, for safety reasons; the only exception is the shortening of profiles from the upper side.
The safety instructions of the assembly instructions must be followed as well as the instructions on the labels of the individual parts.
The indicated nominal current (A) may not be exceeded.
In event of improper use or cleaning with liquids, a risk of an electric shock exists due to possibly exposed live parts. Always
disconnect from power before cleaning or servicing.
If rails or adapters exhibit visible signs of damage, disconnect them immediately and inform your service technician.
Product safety
Single power adapter 24 V
Single power adapters can be used with the XeroLP/L and Xero Twin P/L systems. Low
voltage lighting may only be connected by trained personnel.
If multiple adapters and appliances will be used, their total power consumption may not
exceed the specified nominal current or fuse rating. The permissible nominal voltage and
nominal current are also limited according to the adapters used (see printed label and safety
information).
Permissible nominal current max. 4A.
Only use XeroTwinP/L system accessories! Do not use any other parts.
The user is responsible for ensuring that any connected equipment is electrically, mechanically and thermally compatible with the conductor rail.
Please make sure that the inspector has access to the driver

4
Xero Twin P/L
2
2
12
1
171
6.732"
161
6.339"
63
2.480"
53
2.087"
37.5
1.476"
120 V
L = 1500 mm / 59.055"
NV (24 V)
L = 500 mm / 19.685"
1/2019 (US)
Check the power consumption of electrical appliances! The maximum power consumption should be 10% below the nominal power of the
converter.
Visplay connection system
Powering with 90 W converter
Dimensions of the 90 W converter
1 24 V distributor, 6 way - optional
2 90 W LED converter

5
Xero Twin P/L
349-057.06
349-057.06
+ 0.5 0
+ 0.020” 0
6
0.236”
20
0.787“
+ 0.5 0
+ 0.020” 0
6
0.236”
R 4
0.157”
R 4
0.157”
80
3.150”
16
0.630“
30.4
1.197”
+ 0.3
0
+ 0.012”
0
15
0.591“
wood: 16 mm / 0.630“
Assembly axis: 625mm / 24.606"
Fixing axis Xero Twin P/L accessories
625
24.606"
625
24.606"
625
24.606"
625
24.606"
625
24.606"
150
5.906“
150
5.906"
2300
90.551"
1/2019 (US)
The lower end of the profile is marked with “profile
below”.
Wooden panels on to which Xero Twin P/L is to be fixed,
must be countersunk as follows: (1).
Screw the profile Xero Twin P/L on to the panel from the
rear.
Fix the profile caps 349-057.06 to the top of the profile and
to the bottom of the power supply, before the profile is
installed to the panel (2).
Assembly dimensions / Layout
Xero Twin P/L Aluminium profiles can be screwed on panels or various substructures on the wall.
The accessories from Xero Twin P/L and Xero 8 can be used.
Assembly in wooden panels
Please observe the indications concerning weight loads and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
Recommendation for profile axis with XeroTwinP/L
accessories.
Assembly dimensions: XeroTwinP/L profile screwed on to countersunk wooden panels from the rear / cross-axis
Cross-axis:
Merchandise supports are
positioned centrally and hooked
into one profile.

6
Xero Twin P/L
wood: 16 mm / 0.630"
Fixing axis Xero Twin P/L accessories:
617.5/992.5/1242.5 / 24.311"/39.075"/48.917"
Assembly axis: 637.5/1012.5/1262.5 / 25.098"/39.862"/49.705"
Width of rear panel 607/982/1232
23.898"/38.661"/48.504"
Example: rectangular tube
0
- 0.5
0
- 0.020"
A 637.5
25.098"
A 637.5
25.098"
A 1262 .5
49.705"
A 637.5
25.098"
A 637.5
25.098"
1 2 3
3x
929-226.21
170
6.693“
1/2019 (US)
Assembly dimensions: XeroTwinP/L profile screwed on to substructure and rear panels attached from the front
/ fixed axis distance
Recommendation for profile axis with XeroTwinP/L
and Xero 8 accessories.
Inserting the panels into XeroTwinP/L profile
Fixed axis distance:
Merchandise suports are hooked
into two profiles
(axis 617.5 / 992.5 / 1242.5 mm
24.311" / 39.075" / 48.917").

7
Xero Twin P/L
a
Total length (with infeed and end cap)
3000
/118" / lto
± 1 / ± 0.039"
ø 4.6
0.181"
ø 5.6
0.220"
ced
ef
b
b
optional
e
e
mm in
a
b
c
d
e
f
80
2
27
22
50
9.5
3.150
0.079
1.063
0.866
1.969
0.374
1/2019 (US)
End caps must be fitted on profile with conductor rail.
Take care to assemble the profile in the correct direction (power supply
must be below).
Power supply is available via the left profile slot. The right-hand side is
fitted with a non-powered profile.
Depending to your local regulations, a conduit must be used for the
primary side of the driver. Check this before installation.
It must be ensured that access to the driver is possible for inspection and
subsequent servicing.
Dimensions and distances of holes
All fastening points have to be used in event of maximum loads!
The electrical components and the end cap must be removed before shortening the profile. Always shorten a profile from the top side and
burr the edges. Make sure that all shavings are removed from the profile. The electrical components and end cap must be fitted back onto
the profile.
Shortening a profile

8
Xero Twin P/L
red
blue
3000K/6 W:
332-420.05/.06 580 mm
4000K/6 W:
332-436.05/.06 580 mm
580 / 22.835"
349-189.12/.26/.07
349-182.07/.26/.07
red
blue
349-213.12/.26/.07
332-420.05 580 mm (3000K/6 W)
332-436.05 580 mm (4000K/6 W)
580 / 22.835"
349-183.12/.26/.07
1/2019 (US)
Wooden shelf for brackets with single power adapter
Wooden shelf for brackets
Wooden shelf for T-bracket with single power adapter
Wooden shelf for T-bracket
For wooden shelf max.1245mm/49.016" long by
max.380mm/14.961" deep and max.12W power consumption.
For wooden shelf max.650mm/25.591" long by
max.356mm/14.016" deep and max.6W power consumption.
Production drawings of wooden shelves are available for
downloading on www.visplay.com or can be received on request.
Drawing no. 229-120
Production drawings of wooden shelves are available for
downloading on www.visplay.com or can be received on request.
Drawing no. 252-821
Production drawings of wooden shelves are available for
downloading on www.visplay.com or can be received on request.
Drawing no. 247-841
Production drawings of wooden shelves are available for
downloading on www.visplay.com or can be received on request.
Drawing no. 252-820

9
Xero Twin P/L
1. 2. 3.
1. 2. 3.
1/2019 (US)
Weight loads
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please note that max. permissible load decreases as the merchandise support increases in length.
Please note that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports result in an uneven overall appearance of the goods display.
Please note that the weight limit can be reduced considerably when mounting in glass and sheet metal.
The max. permissible load of the Xero Twin P/L depends on the nature of the wall, the number of fastening points as well as the fastening
material used. All fastening points have to be used in event of a maximum weight load.
Please also observe the weight loads indicated in our sales documentation.
Attaching the glass shelf
The merchandise support has a slight slope (approx. 2°)
Max. load
Profile per  mm/" lbs
Glass shelf with/without LED lighting  lbs
Brackets with/without single power adapter  V for wooden shelf  lbs
T-bracket with/without single power adapter  Vfor wooden shelf  lbs
Fixing set  lbs
Front arm, straight  x mm/ ⁄" x ⁄"  lbs
Side hanging rail  x mm, mm/ ⁄" x ⁄", ", T-Arm  lbs
T-bracket  x mm/" x ⁄" for wooden or glass shelf  lbs
Bracket  x mm/ ⁄" x ⁄" for hanging rail  x mm/ x mm  lbs
Bracket  x mm/ ⁄" x ⁄" for wooden or glass shelf  lbs
Clamping bracket for glass shelf  lbs

Visplay Companies
Oces & Showrooms
Visplay Exclusive Dealers / Sales Agents /
Authorized Distributors
Australia
Distributed by MADE Retail Systems
Authorized Distributor
2 Stephenson Street
Cremorne Vic 3121
Melbourne
Australia
T [phone]
[e-mail]
Brazil
Distributed by Instant Shop
Authorized Distributor
Av. Nove de Julho, 5017 # 51
Cj. 51 - 5° Andar
São Paulo, SP - CEP 01407-200
Brazil
T [phone]
[e-mail]
China
Distributed by Okamura Shanghai
Authorized Distributor
15Fax: B block, FutureLand building
No.5 Lane 388, Zhongjiang Road
Putuo District
Shanghai 200062
China
T [phone]
[e-mail]
Greece
Distributed by KYVERNITIS I. SA
Exclusive Dealer
125, G. Papandreou & Adrianiou str.
144 51 Metamorfosi Athens
Greek
T [phone]
[e-mail]
India
Distributed by
Matrix Visual Innovations Pvt. Ltd.
Authorized Distributor
45/1, 2nd Floor, Corner Market,
Malviya Nagar
New Delhi 110017
India
T [phone]
[e-mail]
Italy
Distributed by Zeppelin s.r.l.
Exclusive Dealer
Via Matteucci, 2
61032 Fano PU
Italy
T [phone]
[e-mail]
Japan
Distributed by
Okamura Corporation
Exclusive Dealer
Higashi Ote Bldg.,
1F1-1-7, Uchikanda, Chiyoda-ku
Tokyo 101-0047
Japan
T [phone]
[email protected]
Panama
Distributed by Vidisplay S.A.
Authorized Distributor
Calle Ramon Jurado,
Paitilla Mall, Local 17 Piso 1
Punta Paitilla
Panama
Ciudad de Panamá
T [phone]
[e-mail]
Poland, Czech Republic & Baltics
Distributed by
Meškank Interior Brands
Sales Agent
T [phone]
[e-mail]
Russia
Distributed by ULTIMATHULE
Exclusive Dealer
Business quartel „ARMA“
Nizhniy Susalniy per., 5 bld.18
105065 Moscow
Russia
T [phone]
[email protected]
Saudi Arabia
Distributed by Saudi TKT
Authorized Distributor
P.O. Box 10700
Jeddah 21443
Saudi Arabia
T [phone]
[e-mail]
Turkey
Distributed by
Dekotek Mimarlık Ltd. Sti
Exclusive Dealer
Sair Nigar Sokak 80/8 Osmanbey
34363 Istanbul
Turkey
T [phone]
[e-mail]
For other countries:
Visplay GmbH
Charles-Eames-Str. 2
79576 Weil am Rhein
T [phone]
[e-mail]
Austria
Visplay Austria
Schottenring 12
1010 Wien
Austria
T [phone]
[e-mail]
Belgium
Visplay Belgium
Woluwelaan 137
1831 Diegem
Belgium
T [phone]
[e-mail]
France
Visplay France
So Square Opéra
5, Rue Boudreau
75009 Paris
France
T [phone]
[e-mail]
Germany
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Germany Showroom
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Netherlands
Visplay Netherlands
De Oude Molen 2
1184 VW Ouderkerk aan de Amstel
Netherlands
T [phone]
[e-mail]
Spain /Portugal/ Latin America
Visplay Spain
Calle Padilla, 21
28006 Madrid
Spain
T [phone]
[e-mail]
United Arab Emirates
Visplay GmbH (Dubai BR)
Sheikh Zayed Road
P.O. B o x: 2 1 3 0 3 5
Sheikha Sana Mana
Al Maktoum Building
Oce - M 10
Dubai
T [phone]
[e-mail]
United Kingdom
Visplay United Kingdom
30 Clerkenwell Road
London EC1M 5PG
United Kingdom
T [phone]
[e-mail]
USA
Visplay Inc.
7528 Walker Way
Allentown, PA 18106
USA
T [phone]
[e-mail]