MERONI UFO Temporary 07 User manual

UFO TEMPORARY 07
ASSEMBLY INSTRUCTIONS
FORD TRANSIT

Rear door right side plate
Side sliding door plate
Side pillar plate
A5
Stud M6x25
A6
n.6 screws
TSPEI M6x20
Rear door left side plate
A2
A1 A3
A4
A7
Bumper plate
A8
n.2 screws
TCEI M8x10
A9
n.2 screws
TSEI M8x30
Adesive felt
A10
ASSEMBLY KIT

ASSEMBLY TOOLS
Wrench Torx 30 Wrench Torx 40
Allen key 6Allen key 5
PICTURE 1
P1

PICTURE 2
PICTURE 3
P2
A5

PICTURE 4
PICTURE 5
A1

PICTURE 6
PICTURE 7
A5
A6

PICTURE 8
PICTURE 9
A6
P3

PICTURE 10
PICTURE 11
P4
A2

PICTURE 12
PICTURE 13
P5
P6

PICTURE 14
PICTURE 15
P7

PICTURE 16
PICTURE 17
P8

PICTURE 18
PICTURE 19
A5
P9

PICTURE 20
PICTURE 21
A3
A5
A6

PICTURE 22
PICTURE 23
A6

PICTURE 24
PICTURE 25
P10
P11

PICTURE 27
PICTURE 26
A9
A7
A8
A10

PICTURE 28
PICTURE 29
P12

PICTURE 30
PICTURE 31
P14
P13
A4

PICTURE 32
PICTURE 33

ASSEMBLY INSTRUCTIONS UFO TEMPORARY - FORD TRANSIT
• Picture 1 Unscrew and remove the torx screw that fixes the rear door lock, right side (see point P1).
• Picture 2 See the performed operation.
• Picture 3 Screw the supplied stud A5 into the door lock to prevent that, after unscrewing the fasteners,
the lock could go out of position from the fixing arrangement. Then unscrew and remove the two torx
screws that fix the lock (see point P2).
• Picture 4 See the performed operation.
• Picture 5 Place the plate A1 in the housing of the stud A5 in correspondence with the fixing holes of the
lock (see picture).
• Picture 6 Fix the plate with the two supplied torx pins A6 and leave them not completely tightened for
final adjustment (see picture). Then unscrew the stud.
• Picture 7 See the performed operation.
• Picture 8 Screw the supplied A6 torx pin into the bracket hole (see picture). Then tighten the three torx
screws of the lock.
• Picture 9 Unscrew the two torx screws that fix the hook on the rear door, left side (see point P3).
• Picture 10 See the performed operation.
• Picture 11 Place the supplied A2 plate in correspondence with the hook fixing holes. Check when fixing
the plate, that the gasket does not remain pressed between the door and the plate edges (see point P4).
• Picture 12 Check that the holes in plate A2 matched with the interaxis distance of the hook fixing holes
(see point P5).
• Picture 13 Fix the hook on the plate using the original pins, leaving them not completely tightened for
final adjustment (see point P6).
• Picture 14 Bring near the doors and make sure that the two plates are aligned (see point P7). Finally,
tighten the screws of the hook on the left door.
• Picture 15 see the completed assembly of the Temporary on the rear doors.
• Picture 16 Unscrew and remove the torx screw that fixes the right sliding door lock (see point P8).
• Picture 17 See the performed operation.
• Picture 18 Screw the supplied stud A5 into the sliding door lock to prevent that, after unscrewing the
fasteners, the lock could go out of position from the fixing arrangement. Then unscrew and remove the
two torx screws that fix the lock (see point P9).
• Picture 19 See the performed operation.
• Picture 20 Place the plate A3 in the housing of the stud A5 in correspondence with the fixing holes of the
lock (see picture).
• Picture 21 Fix the plate with the two supplied torx pins A6 and leave them not completely tightened for
final adjustment (see picture). Then unscrew the stud.
• Picture 22 See the operation.
• Picture 23 Screw the supplied A6 torx screw into the hooks of the plate (see picture). Finally tighten the
three screws torx of the lock.
• Picture 24 Unscrew and remove the two torx screws of the bumper (see point P10).
• Picture 25 See the performed operation. Finally remove the rivet from side panel of the sliding door to
prevent it from bumping under the fixing plate A7.
• Picture 26 See the performed operation.
• Picture 27 Replace the bumper with the the supplied A7 plate with the A9 pins. Then fix the bamper on
the A7 plate with the A8 pins (see picture). Place the felt A10 (see position on the picture).
• Picture 28 Unscrew the torx screws that fix the hook on the pillar (see point P12).
• Picture 29 See the performed operation.
• Picture 30 Overlap the hook to the plate. Fix it with the original screws, leaving them not completely
tightened for final adjustment (see point P13).
• Picture 31 Close the tailgate and check that the two plates are aligned (see point P14). Finally, tighten
the screws of the hook on the pillar.
• Figure 32 See the assembly on the side door.
• Figure 33 See the completed assembly of the Temporary on the Ford Transit.
WARNING: All data contained in the assembly instructions are indicative, and not binding, as the
manufacturer reserves the right to make any changes without prior notice