Metabo UB 18DC Troubleshooting guide

Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
Model
Modèle
Modelo UB 18DC Cordless Work Light
Lampe de Travail Sans Fil
Lámpara de Trabajo Inalámbrica
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this work light can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual BEFORE operating the work light. Please keep this manual available for other
users and owners before they use the work light. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cette lampe de travail peut entraîner
la mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Veuillez lire et de comprendre ce mode d’emploi AVANT d’utiliser la lampe de travail. Laissez
ce mode d’emploi à la disposition des autres utilisateurs et propriétaires avant utilisation de
la lampe de travail. Ce mode d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE
INSTRUCCIONES
ADVERTENCIA
¡Una utilización INCORRECTA O INSEGURA de esta lámpara de trabajo puede provocar
la muerte o daños corporales importantes!
Este manual contiene información importante sobre la seguridad del producto. Lea y
comprenda este manual ANTES de utilizar la lámpara de trabajo. Guarde proporcione este
manual a los demás usuarios y propietarios antes de que utilicen esta lámpara de trabajo.
Este manual debe almacenarse en un lugar seguro.
Without charger and battery
Sans chargeur et batterie
Sin cargador y batería
00BookUB18DCNA.indb100BookUB18DCNA.indb1 2022/01/1713:42:522022/01/1713:42:52

IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction
Manual before operating or maintaining this work light.
Most accidents that result from work light operation and maintenance are caused by the failure to observe
basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous
situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections
which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on
the work light and in this Instruction Manual.
NEVER use this work light in a manner that has not been specifically recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious
injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate
injury, or may cause machine damage.
NOTE emphasizes essential information.
MEANINGS OF SYMBOLS
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.
To reduce the risk of injury, user must
read instruction manual.
0,2m
Keep the light and the object being
illuminated at least 0.2 m apart.
Do not stare at operating lamp. Vvolts
—direct currents
2
English
00BookUB18DCNA.indb200BookUB18DCNA.indb2 2022/01/1713:42:522022/01/1713:42:52

IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using flashlight or lanterns, additional precautions should always be followed, including
the following:
READ ALL THE INSTRUCTIONS BEFORE USING
THE APPLIANCE
WARNING
To reduce the risk of fire, electric shock, or
injury:
1. To reduce the risk of injury, close supervision
is necessary when an appliance is used near
children.
2. Only use attachments recommended or sold
by the manufacturer.
3. Do not use work light in explosive atmospheres,
such as in the presence of flammable or
combustible liquids, gasses or dust.
4. Be careful of electrical shock.
Prevent unintentional starting. Ensure the
switch is the off-position before connecting
to battery cover, picking up or carrying the
appliance.
Carry the appliance with your finger on the
switch or energizing appliance that have the
switch on invites accidents.
5. Disconnect the battery pack from the appliance
before making any adjustments, changing
accessories, or storing appliance.
Such preventive safety measures reduce the
risk of starting the appliance accidentally.
6. Do not cover the work light with cloth,
cardboards or other materials when the light
is on. Keep the light and the object being
illuminated at least 20 cm apart. Failure to
observe these warnings may result in fire.
7. WARNING: To reduce the risk of injury, do not
stare at operating lamp. Serious
eye injury could occur.
8. Do not contact hot parts.
9. Do not use in the rain.
10. Do not leave the work light in a car or the like
that tends to be exposed to be searching heat
of the sun (above 122°F (50°C)). Otherwise,
troubles can result.
11. Do not leave the work light unattended while it
is turned on.
12. When placing the work light in a high location
for use, ensure that the location is stable.
Additionally, secure it in place with string, etc.
to prevent it from falling.
If it falls, it may result in injury or damage.
13. Do not use the work light if the LED cover is
damaged or detached.
14. Do not charge the unit outdoors.
15. Use only the charger supplied by the
manufacturer to recharge. (Manufacturer:
metabo HPT Model: UC18YFSL)
16. Do not incinerate the appliance even if it is
severely damaged. The batteries can explode
in a fire.
17. Do not disassemble or modify the work light.
18. Do not make any modifications to the lamp
or battery, for any defective, please contact
metabo HPT AUTHORIZED SERVICE
CENTER.
GENERAL SAFETY RULES
SAVE THESE
INSTRUCTIONS
1) Work area safety
a) Keep work area clean.
Cluttered areas invite accidents.
b) Do not operate work light in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
3
English
00BookUB18DCNA.indb300BookUB18DCNA.indb3 2022/01/1713:42:532022/01/1713:42:53

2) Electrical safety
a) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
b) To reduce the risk of electrical shock,
do not put in water or other liquid.
3) Personal safety
a) Stay alert, watch what you are doing
and use common sense when use work
light.
4) Battery powered work light use and care
a) Recharge only with the charger
specified by the manufacturer.
A charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b) Use appliances only with specifically
designated battery packs. Use of any
other battery packs may create a risk
of injury and fire.
For use only with metabo HPT BSL36B18
battery pack.
c) When battery pack is not in use, keep
it away from other metal objects like
paper clips, coins, keys, nails, screws,
or other small metal objects that can
make a connection from one terminal
to another.
Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions, liquid may
be ejected from the battery, avoid
contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
5) Service
a) Have your work light serviced by a
qualified repair person using only
identical replacement parts.
This will ensure that the safety of the work
light is maintained.
b) Do not use the lamp when damage is
visible.
SPECIFIC SAFETY RULES
1. Do not use in locations where inflammable
materials such as lacquer, paint, benzene,
thinner or gasoline are present.
Explosion or fires might result.
2. Keep the lamp away from water, open
flames and other heat sources.
3. If you notice that the unit is generating
unusually high temperatures, operating
poorly, or making abnormal noises,
immediately stop using and shut offthe
power switch. Request an inspection
and repair from the dealer where you
purchased the unit or a metabo HPT
Authorized Service Center.
4. If the unit is mistakenly dropped or
strikes another object, make a thorough
check of the unit for cracks, breakage or
deformation, etc.
Injuries might occur if the unit has cracks,
breakage or deformation.
5. Precautions during transport
• Turn the switch offon the tool and remove
the battery.
• Carry the tool by the handle on its body.
• When transporting it via vehicle, take
appropriate steps to prevent it from falling
over or being damaged.
6. NEVER use a work light for applications
other than those specified in the instruction
manual.
7. Handle work light correctly.
Operate the work light according to the
instructions provided herein. Do not drop or
throw the work light. NEVER allow the work
light to be operated by children, individuals
unfamiliar with its operation or unauthorized
personnel.
8. Keep all screws, bolts and covers tightly in
place.
Keep all screws, bolts, and plates tightly
mounted. Check their condition periodically.
9. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine,
carbon tetrachloride, and alcohol may damage
and crack plastic parts. Do not wipe them with
such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dry
thoroughly.
4
English
00BookUB18DCNA.indb400BookUB18DCNA.indb4 2022/01/1713:42:532022/01/1713:42:53

10. Do not use the product if the tool or the
battery terminals (battery mount) are
deformed.
Installing the battery could cause a short circuit
that could result in smoke emission or ignition.
11. Keep the tool’s terminals (battery mount)
free of swarf and dust.
○ Prior to use, make sure that swarf and dust
have not collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool
from falling on the battery.
○ When suspending operation or after use, do
not leave the tool in an area where it may be
exposed to falling swarf or dust.
Doing so could cause a short circuit that could
result in smoke emission or ignition.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result
from improper or unsafe use of battery
chargers. To avoid these risks, follow
these basic safety instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and
operating instructions for battery charger
Model UC18YFSL.
2. Regularly clean the lamp by wiping it with a
soft, dry cloth to remove stubborn dirt, oil etc.
3. To reduce risk of injury, charge metabo HPT
rechargeable battery models of the multi volt
series and the BSL18 series. Other models of
batteries may burst causing personal injury
and damage.
4. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury to
persons.
5. Always use and store the lamp out of the reach
of children.
6. Do not operate battery charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified
serviceman.
7. Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a
risk of electric shock or fire.
8. To reduce risk of electric shock, unplug
charger from receptacle before attempting
any maintenance or cleaning. Removing the
battery will not reduce this risk.
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
BATTERY CHARGER
You must charge the battery before you can
use the tool. Before using the model UC18YFSL
battery charger, be sure to read all instructions and
cautionary statements on it, the battery and in this
manual.
CAUTION
USE ONLY metabo HPT BATTERY MODELS
OF THE MULTI VOLT SERIES AND THE
BSL18 SERIES. OTHER MODELS OF
BATTERIES MAY BURST AND CAUSE
INJURY!
Follow these instructions to avoid the risk of injury:
WARNING
Improper use of the battery or battery
charger can lead to serious injury. To avoid
these injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is
damaged or is completely worn out. The
battery can explode in a fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery
charger’s air vents. Electric shock or damage
to the battery charger may result.
5. NEVER charge outdoors. Keep the battery
away from direct sunlight and use only where
there is low humidity and good ventilation.
6. NEVER charge when the temperature is below
32°F (0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for
the battery or the battery charger.
9. NEVER use a booster transformer when
charging.
10. NEVER use DC power to charge.
11. NEVER store the battery or battery charger in
places where the temperature may reach or
exceed 104°F (40°C) such as inside metal box
or car.
5
English
00BookUB18DCNA.indb500BookUB18DCNA.indb5 2022/01/1713:42:532022/01/1713:42:53

12. NEVER expose the battery or battery charger
to rain or wet conditions.
13. ALWAYS operate charger on standard
household electrical power (120 volts). Using
the charger on any other voltage may overheat
and damage the charger.
14. ALWAYS wait at least 15 minutes between
charges to avoid overheating the charger.
15. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 to 3 described below, when using
this product, even if the switch is turned ON, the light
may not turn on. This is not the trouble but the result
of protection function.
1. When the remaining battery power runs out,
the light turns off.
In such case, charge it up immediately.
2. If the tool is overloaded, the light may turn off.
In this case, release the switch of tool and
eliminate causes of overloading. After that, you
can use it again.
3. If the battery is overheated under overload
work, the battery power may stop.
In this case, stop using the battery and let the
battery cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat
generation, smoke emission, explosion and ignition
beforehand, please be sure to heed the following
precautions.
1. Make sure that swarf and dust do not collect on
the battery.
○ During work make sure that swarf and dust do
not fall on the battery.
○ Make sure that any swarf and dust falling on the
tool during work do not collect on the battery.
○ Do not store an unused battery in a location
exposed to swarf and dust.
○ Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it
together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such
as a nail, strike with a hammer, step on, throw
or subject the battery to severe physical shock.
3. Do not use an apparently damaged or
deformed battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets
or car cigarette lighter sockets.
6. Do not use the battery for a purpose other than
those specified.
7. If the battery charging fails to complete even
when a specified recharging time has elapsed,
immediately stop further recharging.
8. Do not put or subject the battery to high
temperatures or high pressure such as into
a microwave oven, dryer, or high pressure
container.
9. Keep away from fire immediately when leakage
or foul odor are detected.
10. Do not use in a location where strong static
electricity generates.
11. If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any
way appears abnormal during use, recharging
or storage, immediately remove it from the
equipment or battery charger, and stop use.
12. Do not immerse the battery or allow any fluids
to flow inside. Conductive liquid ingress, such
as water, can cause damage resulting in fire
or explosion. Store your battery in a cool, dry
place, away from combustible and flammable
items. Corrosive gas atmospheres must be
avoided.
CAUTION
1. If liquid leaking from the battery gets into your
eyes, do not rub your eyes and wash them well
with fresh clean water such as tap water and
contact a doctor immediately.
If left untreated, the liquid may cause eye-
problems.
2. If liquid leaks onto your skin or clothes, wash
well with clean water such as tap water
immediately.
There is a possibility that this can cause skin
irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when
using the battery for the first time, do not use
and return it to your supplier or vendor.
6
English
00BookUB18DCNA.indb600BookUB18DCNA.indb6 2022/01/1713:42:532022/01/1713:42:53

WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit
may occur resulting in the risk of fire. Please observe
the following matters when storing the battery.
○ Do not place electrically conductive
cuttings, nails, steel wire, copper wire or
other wire in the storage case.
○ Either install the battery in the tool or store
by securely pressing into the battery cover
until the ventilation holes are concealed to
prevent short-circuits (See Fig. 3).
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please
observe the following precautions.
WARNING
Notify the transporting company that a package
contains a lithium-ion battery, inform the
company of its power output and follow the
instructions of the transportation company
when arranging transport.
● Lithium-ion batteries that exceed a power
output of 100Wh are considered to be in
the freight classification of Dangerous
Goods and will require special application
procedures.
● For transportation abroad, you must
comply with international law and the rules
and regulations of the destination country.
Wh
Power Output
2 to 3 digit number
Fig. 1
PRECAUTIONS WHEN CONNECTING
TO EXTERNAL EQUIPMENT
Unexpected problems may result in the loss or
corruption of data stored in smartphones and other
peripheral equipment connected to the work light.
With this possibility in mind, a backup of the data
should always be made in advance.
Note that metabo HPT cannot be held responsible
for the corruption or loss of data stored within
smartphones and other peripheral equipment
connected to the work light, nor any damage to the
equipment itself.
7
English
00BookUB18DCNA.indb700BookUB18DCNA.indb7 2022/01/1713:42:532022/01/1713:42:53

PRECAUTIONS REGARDING THE DUST-RESISTANCE AND WATER-PROOFING
FUNCTIONS
This product conforms to IP54 protection class ratings (dust-resistance and water-proofing) for electrical
equipment as stipulated by the international IEC regulations. (When the battery is attached to the tool’s
body, and the battery cover and rubber cover are closed, the tool’s body alone meets the equivalent of the
IP54 protection standard.)
[Descriptions of IP Codes]
IP54
Protection rating for water penetration
There is no harmful effect from water splashing from any direction.
Protection rating for external assault by solid objects
Dust that may cause adverse effects on the equipment must not be able to enter (dust-resistance).
The equipment has been designed to withstand the effects of dust and water, but there is no guarantee that it
will not malfunction. Do not use or leave the equipment in locations where it is subject to excessive amounts
of dust, or in locations where it is submerged in water or subject to rainwater.
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS WORK LIGHT!
8
English
00BookUB18DCNA.indb800BookUB18DCNA.indb8 2022/01/1713:42:532022/01/1713:42:53

FUNCTIONAL DESCRIPTION
NOTE
The information contained in this Instruction Manual is designed to assist you in the safe operation and
maintenance of the work light.
NEVER operate, or attempt any maintenance on the work light unless you have first read and understood
all safety instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on
your own work light.
NAME OF PARTS
1. Cordless Work Light (UB18DC)
LED cover
Switch
Hook-hole for
wall hanging
Remaining battery
indicator lamp
Adjustment dial
LED lights
(internal)
USB port
Screw hole for tripod
(5/8-UNC)
Lock
Battery cover
Bottom handle
Top handle
Battery
(sold separately)
Fig. 2
2. Battery
(optional accessories…sold separately) 3. Battery Charger (optional accessories…sold separately)
Ventilation holes
Latch
Terminals
Battery cover
Battery Nameplate
Pilot lamp
Guide rail
Cord
Ventilation holes
<BSL1830C>
Fig. 3
<UC18YFSL>
Fig. 4
9
English
00BookUB18DCNA.indb900BookUB18DCNA.indb9 2022/01/1713:42:532022/01/1713:42:53

SPECIFICATIONS
1. Cordless Work Light
Model UB18DC
LED (white) ×60
Brightness adjustment range 700–4,000 lm
Operating time,
approx. (Using full
charged battery)*
3.0 Ah 5.0 Ah 8.0 Ah
4,000 lm Approx. 1.5 hours Approx. 3 hours Approx. 4.5 hours
700 lm Approx. 12 hours Approx. 20 hours Approx. 30 hours
Battery Type Li-ion battery Model BSL1830C
Voltage DC 18 V
Weight (without battery) 4.2 lbs. (1.9 kg)
* The operating times shown are reference values only.
The actual time varies depending on the type and charging state of the battery, the usage conditions,
etc.
2. Battery Charger
Model UC18YFSL
Input power source Single phase: AC 120 V 60 Hz
Charging time
(At a temperature of 68°F (20°C)) BSL1830C: Approx. 45 min
Charging voltage DC 14.4–18 V
Charging current DC 3.5 A
Weight 1.1 lbs. (0.5 kg)
NOTE: The charging time may vary according to temperature and power source voltage.
10
English
00BookUB18DCNA.indb1000BookUB18DCNA.indb10 2022/01/1713:42:542022/01/1713:42:54

ASSEMBLY AND OPERATION
APPLICATIONS
Illumination of work site
REMOVAL AND INSTALLATION
METHOD OF BATTERY
○
How to install the battery.
Press the lock to release it, and open the
battery cover.
Always insert it all the way until it locks in place
with a little click. Then, close the battery cover,
and secure it with the lock. (Fig. 5).
Press the lock
Insert
Open the
battery cover
Click
Battery
Fig. 5
○ How to remove the battery.
Open the battery cover, and while pressing the
2 latches (one on each side), slide it and pull it
out. Close the battery cover, and secure it with
the lock. (Fig. 6).
Battery
Press
Pull out
Latches
(Both sides)
Fig. 6
NOTE
Ensure that the battery cover is securely
closed unless you are removing or installing
the battery.
If any water or dust enters the body of the tool
or the terminals of the battery, a failure may
occur.
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure
the following points.
○ The power source voltage is stated on the
nameplate.
○ The cord is not damaged.
WARNING
Do not charge at voltage higher than
indicated on the nameplate.
If charged at voltage higher than indicated
on the nameplate, the charger will burn
out.
1. Connect the charger’s power cord to a
receptacle. When the power cord is connected,
the charge indicator lamp will blink in red. (At
1-second intervals)
11
English
00BookUB18DCNA.indb1100BookUB18DCNA.indb11 2022/01/1713:42:542022/01/1713:42:54

3. Charging
When inserting a battery in the charger, the
pilot lamp will light up continuously in red.
When the battery becomes fully recharged,
the pilot lamp will blink in red. (At 1- second
intervals.) (See Table 2)
(1) Lamp indication
The indications of the pilot lamp will be as
shown in Table 2, according to the condition of
the battery charger or the battery.
WARNING
Do not use the electrical
cord if damaged. Have it
repaired immediately.
2. Insert the battery to the battery charger.
Firmly Insert the battery into the battery charger
as shown in Fig. 7.
Battery
Guide rail
Pilot lamp
Fig. 7
Table 2
Indications of the pilot lamp
Pilot lamp
(red)
Before
charging Blinks Lights for 0.5 seconds. Does not light
for 0.5 seconds. (offfor 0.5 seconds)
While
charging Lights Lights continuously
Charging
complete Blinks Lights for 0.5 seconds. Does not light
for 0.5 seconds. (offfor 0.5 seconds)
Overheat
standby Blinks Lights for 1 second. Does not light for
0.5 seconds. (offfor 0.5 seconds)
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Charging
impossible Flickers Lights for 0.1 seconds. Does not light
for 0.1 seconds. (offfor 0.1 seconds) Malfunction in the battery
or the charger
12
English
00BookUB18DCNA.indb1200BookUB18DCNA.indb12 2022/01/1713:42:542022/01/1713:42:54

(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries
are as shown in the Table 3, and batteries that
have become hot should be cooled for a while
before being recharged.
Table 3
Rechargeable
batteries Temperatures at which the battery can be recharged
BSL1830C 32°F–122°F
(0°C–50°C)
(3) Regarding recharging time (At 68°F (20°C))
Table 4 Charging time
Charger
Battery UC18YFSL
BSL1830C Approx. 45 min
NOTE
The recharging time may vary according to the
ambient temperature.
4. Disconnect battery charger from the
receptacle.
CAUTION
Do not pull the plug out of the receptacle
by pulling on the cord.
Make sure to grasp the plug when removing
from receptacle to avoid damaging cord.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull
out the battery from the battery charger.
NOTE
Be sure to pull out the battery from the battery
charger after use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new
batteries and batteries that have not been
used for an extended period is not activated,
the electric discharge might be low when
using them the first and second time. This is
a temporary phenomenon, and normal time
required for recharging will be restored by
recharging the batteries 2–3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool
becomes weaker, stop using the tool and
recharge its battery. If you continue to use
the tool and exhaust the electric current,
the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately
after use. If such a battery is recharged
immediately after use, its internal chemical
substance will deteriorate, and the battery
life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
● When the battery charger has been
continuously used, the battery charger will
be heated, thus constituting the cause of
the failures. Once the charging has been
completed, give 15 minutes rest until the
next charging.
● If the battery is charged while it is heated
because it has been left for a long time
in a location subject to direct sunlight or
because the battery has just been used,
the pilot lamp of the charger lights for
1 second, does not light for 0.5 seconds
(offfor 0.5 seconds).
The battery will not be recharged. In such a
case, let the battery cool before charging.
● When the pilot lamp flickers (at 0.2-second
intervals), check for and take out any
foreign objects in the charger’s battery
connector. If there are no foreign objects,
it is probable that the battery or charger is
malfunctioning. Take it to your authorized
Service Center.
13
English
00BookUB18DCNA.indb1300BookUB18DCNA.indb13 2022/01/1713:42:542022/01/1713:42:54

HOW TO USE
1. About remaining battery indicator
When the light turns on, the remaining
battery indicator lamp turns on and shows the
remaining battery. When the remaining battery
becomes low, the light briefly blinks about once
every 3 minutes. (Fig. 8)
Table 5
State of lamp Battery Remaining Power
Over 80%
60%–80%
40%–60%
20%–40%
Less than 20%
As the remaining battery indicator shows somewhat
differently depending on ambient temperature and
battery characteristics, read it as a reference.
Remaining battery
indicator lamp
Press the switch
to turn on the
LED light
Fig. 8
NOTE
○ When using a Multi-volt battery, please refer to
the indicator lamp on the battery for the battery
remaining power.
○ Do not give a strong shock to the switch panel
or break it. It may lead to a trouble.
2. Turning the light on
Press the switch to turn the light on.
Use the adjustment dial that surrounds the
switch to adjust the brightness.
When the brightness reaches the maximum
(4,000 lm) or the minimum (700 lm), the light
briefly blinks twice. (Fig. 9)
Turn the adjustment
dial to adjust the
brightness
Press the switch to
turn on the LED light
Fig. 9
3. Changing the angle of the light
The vertical angle can be changed 138°
(120° upward and 18° downward). (Fig. 10)
138° vertically
Fig. 10
14
English
00BookUB18DCNA.indb1400BookUB18DCNA.indb14 2022/01/1713:42:542022/01/1713:42:54

4. Mounting on a wall for use
The work light can be used with its body
mounted on a wall using the hook-hole for wall
hanging. (Fig. 11)
Screw a wood screw, etc. into the wall with
the head of the screw protruding, then hang
the work light on it so that the screw passes
through the groove of the hook-hole for wall
hanging.
Wood screw
Hook-hole for
wall hanging
Fig. 11
5. Securing to a tripod
The work light can be secured to a tripod using
the screw hole for tripod (5/8-UNC). (Fig. 12)
Tripod
Fig. 12
NOTE
When using a tripod, ensure that it is stable so
that it does not fall over.
6. How to recharge USB device
WARNING
○ Prior to use, check the connecting USB
cable for any defect or damage.
Using a defective or damaged USB cable
can cause smoke emission or ignition.
○ When the product is not being used, cover
the USB port with the rubber cover.
Buildup of dust etc. in the USB port can
cause smoke emission or ignition.
Open the rubber cover of the USB port, and firmly
plug in a commercially available USB cable into the
USB port. (Fig. 13)
USB port
USB cable
Rubber cover
Fig. 13
NOTE
○ If the remaining battery becomes low, USB
output is automatically stopped, and the work
light cannot charge USB devices.
○ The charging time differs depending on the
type of USB device being used.
○ Do not use for any purpose other than charging
a USB device.
○ It may not be possible to charge some types of
USB devices.
15
English
00BookUB18DCNA.indb1500BookUB18DCNA.indb15 2022/01/1713:42:552022/01/1713:42:55

MAINTENANCE AND INSPECTION
WARNING
When not using the work light for a long time, performing maintenance on it, inspecting it, or
storing it, be sure to turn OFF the switch and pull out the battery.
1. Check the Screws
Loose screws are dangerous. Regularly
inspect them and make sure they are tight.
WARNING
Using this work light with loosened screws
is extremely dangerous.
2. Check for Dust
Dust may be removed with a soft cloth or a
cloth dampened with soapy water.
Do not use bleach, chlorine, gasoline or thinner,
for they may damage the plastics.
3. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have
not collected on the terminals.
On occasion check prior, during and after
operation.
CAUTION
Remove any swarf or dust which may have
collected on the terminals.
Failure to do so may result in malfunction.
4. Disposal of the exhausted battery
WARNING
Do not dispose of the exhausted
battery. The battery must explode if it is
incinerated. The battery is recyclable. At
the end of it’s useful life, under various
state and local laws, it may be illegal to
dispose of this battery into the municipal
waste stream. Check with your local solid
waste officials for details in your area for
recycling options or proper disposal.
5. Storage
Storing in a place below 104°F (40°C) and out
of the reach of children.
NOTE
Storing lithium-ion batteries
Make sure the lithium-ion batteries have been
fully charged before storing them.
Prolonged storage (3 months or more) of
batteries with a low charge may result in
performance deterioration, significantly
reducing battery usage time or rendering the
batteries incapable of holding a charge.
If the battery usage time is extremely short
despite repeated charging and use, consider
the batteries dead and purchase new batteries.
6. Service and repairs
All quality work light will eventually require
servicing or replacement of parts because
of wear from normal use. To assure that only
authorized replacement parts will be used,
all service and repairs must be performed
by a metabo HPT AUTHORIZED SERVICE
CENTER, ONLY.
CAUTION
In the operation and maintenance of work
light, the safety regulations and standards
prescribed in each country must be
observed.
Important notice on the batteries for the
metabo HPT cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when
used with batteries other than these designated
by us, or when the battery is disassembled and
modified (such as disassembly and replacement
of cells or other internal parts).
16
English
00BookUB18DCNA.indb1600BookUB18DCNA.indb16 2022/01/1713:42:552022/01/1713:42:55

ACCESSORIES
WARNING
ALWAYS use Only authorized metabo HPT replacement parts and accessories. NEVER use
replacement parts or accessories which are not intended for use with this work light. Contact
metabo HPT if you are not sure whether it is safe to use a particular replacement part or
accessory with your work light.
The use of any other attachment or accessory can be dangerous and could cause injury or
mechanical damage.
NOTE
Accessories are subject to change without any obligation on the part of the metabo HPT.
STANDARD ACCESSORIES
UB18DC
(NN) Battery, Battery charger and Battery cover are not contained.
17
English
00BookUB18DCNA.indb1700BookUB18DCNA.indb17 2022/01/1713:42:562022/01/1713:42:56

INFORMATIONS IMPORTANTES DE SÉCURITÉ
Veuillez lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de
fonctionnement présents dans ce mode d’emploi avant d’utiliser ou d’entretenir cette lampe de travail.
La plupart des accidents causés lors de l’utilisation ou de l’entretien d'une lampe de travail proviennent d’un
non-respect des règles ou précautions de base de sécurité. Un accident peut la plupart du temps être évité si
l’on reconnaît une situation de danger potentiel avant qu’elle ne se produise, et en observant les procédures
de sécurité appropriées.
Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode
d’emploi et dans les sections qui contiennent les instructions de fonctionnement et d’entretien.
Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un endommagement de la
machine sont identifiés par AVERTISSEMENTS sur la lampe de travail et dans ce mode d’emploi.
N’utilisez JAMAIS cette lampe de travail d’une manière qui n’est pas spécifiquement recommandée par
metabo HPT.
SIGNIFICATION DES MOTS D’AVERTISSEMENT
AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient
entraîner la mort ou de sérieuses blessures.
PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent
entraîner de mineures et légères blessures ou endommager la machine.
REMARQUE met en relief des informations essentielles.
SIGNIFICATION DES SYMBOLES
Symboles
AVERTISSEMENT
Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur signification avant d’utiliser
l’outil.
Pour réduire tout risque de blessure,
l’utilisateur doit lire le mode d’emploi.
0,2m
Gardez la lampe et l’objet éclairé à une
distance d’au moins 0,2 m.
Ne regardez pas fixement la lampe
allumée.
Vvolts
—courants continus
18
Français
00BookUB18DCNA.indb1800BookUB18DCNA.indb18 2022/01/1713:42:562022/01/1713:42:56

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
AVERTISSEMENT – Lorsque vous utilisez une lampe de poche ou une lanterne, vous devriez toujours
prendre des précautions additionnelles, notamment les suivantes:
LIRE TOUTES LES INSTRUCTIONS AVANT
D’UTILISER L’APPAREIL
8. Ne pas toucher les pièces chaudes.
9. Ne pas utiliser sous la pluie.
10. Ne laissez pas la lampe de travail dans un
véhicule ou similaire, où elle risque d’être
exposé à la chaleur du soleil (supérieure à
122°F (50°C)). Elle risque sinon de présenter
un dysfonctionnement.
11. Ne laissez pas la lampe de travail sans
surveillance lorsqu’elle est allumée.
12. Lorsque vous placez la lampe de travail en
hauteur pour l’utiliser, assurez-vous que
l’emplacement est stable. De plus, fixez-la
en place au moyen d’une corde, etc. pour
l’empêcher de tomber.
En cas de chute, cela peut entraîner des
blessures ou des dommages.
13. N’utilisez pas la lampe de travail si le couvercle
du voyant à DEL est endommagé ou détaché.
14. Ne rechargez pas l’unité à l’extérieur.
15. Utilisez exclusivement le chargeur fourni
par le fabricant pour recharger. (Fabricant:
metabo HPT modèle: UC18YFSL)
16. Ne pas incinérer l’appareil même s’il est
gravement endommagé. Les batteries peuvent
exploser lors d’un incendie.
17. Ne démontez pas et ne modifiez pas la lampe
de travail.
18. Ne pas apporter de modification à la lampe ou
à la batterie. En cas de défectuosité, prière de
communiquer avec UN CENTRE DE SERVICE
metabo HPT AUTORISÉ.
AVERTISSEMENT
Pour réduire le risque d’incendie, de choc
électrique ou de blessure:
1. Pour réduire les risques de blessures, une
surveillance étroite est nécessaire lorsqu’un
appareil est utilisé près d’enfants.
2. Utiliser seulement les accessoires
recommandés ou vendus par le fabricant.
3. N’utilisez pas la lampe de travail dans des
atmosphères explosives, notamment en
présence de liquides, de gaz ou de poussières
inflammables ou combustibles.
4. Veillez à éviter les chocs électriques.
Éviter tout démarrage intempestif. S’assurer
que l’interrupteur est en position d’arrêt avant
de connecter l’appareil au couvercle de
batterie, de le ramasser ou de le porter.
Porter l’appareil en ayant le doigt sur
l’interrupteur ou brancher un appareil dont
l’interrupteur est en position de marche est
source d’accidents.
5. Déconnecter la batterie de l’appareil avant
d’effectuer des réglages, de changer les
accessoires ou de ranger l’appareil.
De telles mesures de sécurité préventive
réduisent le risque de démarrage accidentel
de l’appareil.
6. Ne pas couvrir la lampe de travail avec un tissu,
du carton ou tout autre matériau lorsqu’elle
est allumée. Gardez la lampe et l’objet éclairé
à une distance d’au moins 20 cm. Le non-
respect de ces mises en garde peut entraîner
un incendie.
7. AVERTISSEMENT: Pour réduire le risque de
blessure, ne pas regarder
fixement la lampe allumée.
De graves blessures
oculaires pourraient
survenir.
19
Français
00BookUB18DCNA.indb1900BookUB18DCNA.indb19 2022/01/1713:42:562022/01/1713:42:56

REGLES GENERALE DE SECURITE
CONSERVER CES
INSTRUCTIONS
1) Sécurité de l’aire de travail
a) Maintenir l’espace de travail propre.
Les endroits en désordre sont propices
aux accidents.
b) N’utilisez pas la lampe de travail
en présence de liquides, gaz ou
poussières inflammables, au risque de
provoquer une explosion.
2) Sécurité électrique
a) Eviter tout contact avec les surfaces
mises à la masse telles que les tuyaux,
radiateurs, bandes et réfrigérateurs.
Le risque de choc électrique est accru en
cas de mise à la masse du corps.
b)Pour réduire le risque de choc
électrique, ne pas verser dedans d’eau
ou d’autres liquides.
3) Sécurité personnelle
a) Rester vigilant, regarder ce que vous
êtes en train de faire et faire preuve de
bon sens dans votre utilisation de la
lampe de travail.
4) Utilisation et entretien de la lampe de
travail alimenté sur batterie
a) Rechargez la batterie uniquement
avec le chargeur recommandé par le
fabricant.
Un chargeur qui est compatible à un type
bien précis de batterie peut entraîner un
risque d’incendie s’il est utilisé avec une
autre batterie.
b) N’utiliser les appareils qu’avec des
batteries spécifiquement désignées.
L’utilisation de toute autre batterie
peut présenter un risque de blessure
et d’incendie.
À utiliser seulement avec la batterie
metabo HPT BSL36B18.
c) Lorsque la batterie est inutilisée, la
garder à l’écart d’objets métalliques
comme des trombones, des pièces
de monnaie, des clés, des clous, des
vis ou autres petits objets métalliques
pouvant raccorder les bornes.
La connexion des bornes peut entraîner
des blessures ou un incendie.
d) En cas d’utilisation dans des conditions
extrêmes, du liquide peut être émis de
la batterie. Éviter tout contact. en cas
de contact accidentel, rincer à l’eau.
Si le liquide entre en contact avec les
yeux, consulter un médecin.
Le liquide émis par la batterie peut
entraîner des irritations et des brûlures.
5) Service
a) Faites entretenir la lampe de travail
par un technicien habilité utilisant
exclusivement des pièces de rechange
identiques.
Cela garantira la sécurité de la lampe de
travail.
b) Ne pas utiliser la lampe si des
dommages sont visibles.
RÈGLES DE SÉCURITÉ SPÉCIFIQUES
1. N’utilisez pas la lampe de travail en
présence de matériaux inflammables tels
que la laque, la peinture, le benzène, le
diluant ou la gazoline.
Cela peut provoquer une explosion ou un
incendie.
2. Tenir la lampe à l’écart de l’eau, des
flammes nues et d’autres sources de
chaleur.
3. Si vous observez que l'appareil génère
des températures anormalement élevées,
fonctionne mal ou produit des bruits
anormaux, cessez immédiatement
l'utilisation et coupez l'interrupteur
d'alimentation. Faites-le inspecter et
réparer chez votre distributeur ou dans un
service après-vente metabo HPT agréé.
4. Si l’unité tombe ou se cogne
malencontreusement contre un autre
objet, inspectez-la minutieusement pour
vérifier l’absence de craquelures, de
cassures ou de déformations, etc.
Toute craquelure, cassure ou déformation peut
entraîner des blessures.
5. Précautions pendant le transport.
• Éteignez l’outil et retirez la batterie.
• Transportez l’outil par sa poignée.
• Lorsque la machine est transportée
à l’intérieur d’un véhicule, prenez des
mesures adaptées pour éviter qu'elle ne
chute et ne soit ainsi détériorée.
20
Français
00BookUB18DCNA.indb2000BookUB18DCNA.indb20 2022/01/1713:42:562022/01/1713:42:56