Metalumen Grande RM4D Series User manual

Page 1of 4
Specifications and design subject to change without notice. 570 Southgate Drive, Guelph, Ontario, Canada, N1G 4P6
www.metalumen.com Phone: [phone] Fax: [phone]
IS-0244-03 rev.00
GRANDE RECESSED TBAR LED
INSTALLATION INSTRUCTIONS
NOTE: The following instructions provide general guidelines for product installation. For additional information consult the
applicable electrical codes or contact factory directly for support before attempting anything with uncertainty.
CAUTION: Do not assemble fixture runs on floor.
WARNING: Risk of fire and electrical shock. DISCONNECT POWER AT ELECTRICAL PANEL before installing or
servicing this product.
General Safety Instructions:
1. Read all instructions prior to installing this fixture.
2. This product must be installed in accordance with the applicable installation code by a person familiar with the
construction and operation of the product and the hazards involved.
3. All wiring must be performed by a qualified electrician in accordance with national and local building and electrical codes.
4. This fixture must be suitably grounded for your protection against shock hazards and to assure proper operation.
5. Make sure that the power source conforms to the requirements of this fixture.
Wiring Diagram:
MAIN PARTS LIST:
A. Luminaire enclosure
B. Tbar Hanger Bracket
C. End plate
D. Lens
E. Lens Filler &Magnet
F. Retainer Clip
OTHER PARTS:
Reflector/LED assembly
Standard wiring
With optional Emergency Pack
A
D
C
E
F

Page 2of 4
Specifications and design subject to change without notice. 570 Southgate Drive, Guelph, Ontario, Canada, N1G 4P6
www.metalumen.com Phone: [phone] Fax: [phone]
IS-0244-03 rev.00
GRANDE RECESSED TBAR LED
INSTALLATION INSTRUCTIONS
Step-by-step Instructions:
Step 1: Remove fixture packaging; note marked supply
wires coming out at one end of the luminaire.
Step 2: Ensure Retainer clip (F) is loose. If not, loosen
retainer clips (4)
Step 3: Place Luminaire Fixture (A) into ceiling and rest
on tbar.
Step 4: Adjust Retainer Clips so its sits tight against tbar.
Step 5: Once Retainer clips are tight against tbar
fasten screws to secure Retainer Clips in location.
Step 6: Remove lens filler and magnet (E)

Page 3of 4
Specifications and design subject to change without notice. 570 Southgate Drive, Guelph, Ontario, Canada, N1G 4P6
www.metalumen.com Phone: [phone] Fax: [phone]
IS-0244-03 rev.00
GRANDE RECESSED TBAR LED
INSTALLATION INSTRUCTIONS
Step-by-step Instructions:
Step 7: Remove lens (D) starting at one end.
Pull one side first, rotate and detach. Keep lens.
Step 8: Remove reflector mounting screws and
reflector/LED assembly. Note fixtures with optional
emergency pack have a test switch and indicator light
mounted on the reflector.
.
Step 9: Bring electrical supply to the fixture as needed.
Make sure all Retaining Clips are secured and
fastened.
Step 10: Perform electrical wiring inside the fixture and
re-attach reflector/LED assembly with mounting screws.
Optional emergency driver must be fed from the same
branch circuit as the AC driver
Step 11: Re-attach lens. Start with one side first and
close the other side starting from the corner.
Step 12: Re-attach the filler and magnet E).

Page 4of 4
Specifications and design subject to change without notice. 570 Southgate Drive, Guelph, Ontario, Canada, N1G 4P6
www.metalumen.com Phone: [phone] Fax: [phone]
IS-0244-03
rev.00
GRANDE RECESSED TBAR LED
INSTALLATION INSTRUCTIONS
Step-by-step Instructions:
Installed Fixture (A).