FXLuminaire A-BR10 User manual

LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
INSTALL NOTE: A-BR10
1. Caution and Safety Instructions
•Qualied personnel must install this product in
a manner consistent with its intended use and
in compliance with the National Electrical Code,
Canadian Electrical Code, and/or all local and
provincial Codes.
•Follow all product label information and
installation instructions.
•Qualied personnel must perform all servicing
of this product.
•Turn o power at the fuse or circuit breaker
before installation or servicing.
•The use of damaged components may cause an
unsafe condition and void the product warranty.
•Do not block light emanating from the product
in whole or part.
•Never operate the xture with a missing or
damaged lens. The lens must be cleaned on
a regular basis.
•Portions of the xture may become extremely
hot. Do not touch the hot lens or xture body.
Do not touch the light source at any time.
•Keep all gaskets and sealing surfaces clean
during installation and servicing; failure to do
so may lead to premature failure of the product.
Tools Needed
Installation: ⁄ " (14 mm), ⁄ " (11 mm) wrench or socket, and
⁄ " Allen key
Servicing: #2 Phillips screwdriver
Standard
Voltage (SV)
Universal
Voltage (UV)
High
Voltage (HV)
Input Power 120V/60Hz 110V to 277V/60Hz 220V to 240V/50Hz
Dimming Phase 0-10V N/A
Number of Wires 3 5 3
Black, White, Green Black, White, Green,
Purple, Gray
Brown, Blue,
Green/Yellow
Bolt Pattern Dimensions:
Top View
2.5" (64 mm)
Radius
Note: Front arrow
indicates orientation
of xture.
Power Requirements
2. Product Information 3YJ8
67
IP

LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
INSTALL NOTE: A-BR10
1. Assemble the install ring, install spacer, and
⁄" (10 mm) anchor bolts (included) to prepare
for installation in a concrete base. Be sure to
follow local codes and structural guidelines for
sizing of the concrete base.
2. Plumb conduit/cabling through the center of
the install ring.
Install ring
Install spacer
Anchor bolts
3. Ensure the ring and install spacer are ush with
the concrete surface.
Install spacer
Install ring
Wiring Chart (SV/UV – 60Hz)
Wiring Chart (HV – 50Hz)
BlackLine/Hot/Switching
WhiteCommon
Green (via stud or
green lead)
Ground
Gray*0-10V (-)
Purple*0-10V (+)
FIXTUREFIXTURE
BUILDINGBUILDING
*For use with 0-10V driver only
*For use with 0-10V driver only
BrownLine/Hot/Switching
BlueCommon
Green/YellowGround
Black*0-10V (-)
Gray*0-10V (+)
4. Carefully support the xture while connecting
the wires. Be sure to use the appropriate wiring
chart and approved wire connectors.
3. Product Installation

LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
INSTALL NOTE: A-BR10
3. Product Installation
5. Li the xture assembly and lower it onto the
mounting base assembly.
6. Align the four tabs with the grooves in the
install rings.
7. Hand-turn the main assembly clockwise 45°
until the main assembly locks in place.
8. Lock the main assembly in place by
tightening the ⁄" (6 mm) install rod at the
top of main assembly until it bottoms out on
the mounting base.
⁄" (6mm)
Install rod
⁄" (6 mm)
Install rod
Mounting base
9. Place the cap on top of the main assembly.
⁄ " (4 mm)
Allen key
10. Hand-turn the cap clockwise until the tabs
engage and lock the cap in place.
11. Using a ⁄" Allen key, tighten the 10-32
setscrew at the underside of the light opening
to lock the top cap in place.

FX-296-IN 4/20LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
INSTALL NOTE: A-BR10
4. Warranty
STATEMENT OF LIMITED WARRANTY
Hunter Industries Incorporated (“Hunter”) warrants FX Luminaire Line-Voltage Series lighting products to be free of defects in materials
or workmanship under normal use for a period of ve (5) years from the date of invoice. If a defect in a FX Luminaire product is discovered
during the applicable warranty period, Hunter will repair or replace, at its option, the product or the defective part. This limited warranty
does not extend to repairs, adjustments, or replacement of FX Luminaire products or parts resulting from misuse, negligence, alteration,
modication, tampering, or improper installation and/or maintenance of the product. This warranty extends only to the original installer
of the product. If a defect arises in a FX Luminaire product or part during the warranty period, contact the local authorized manufacturer’s
representative. Hunter’s obligation to repair or replace its products as set forth above is the sole and exclusive warranty set forth by Hunter.
There are no other warranties, expressed or implied, including warranties of merchantability and tness for a particular purpose. Hunter
will not be liable to distributor or any other party in strict liability, tort, contract, or any other manner for damages caused or claimed to be
caused as a result of any design or defect in FX Luminaire products, or for any special, incidental, consequential, or exemplary damages
or any nature, including without limitation lost business or prots. Notwithstanding the foregoing, if for any reason Hunter is found to be
liable, in no event shall Hunter’s liability exceed the price of the product which gives rise to the claim, loss, or damage.
If you have any questions concerning the warranty or its application, please write to:
Customer Service Department
FX Luminaire
1940 Diamond Street
San Marcos, CA 92078 USA