Metra Electronics CS-1X4HDSPLEXT User manual

MetraHomeTheater.com
866-839-9187
460 Walker Street
Holly Hill, FL 32117-2653
©2017 Metra Electronics Corporation
Designed and Manufactured to
Metra Home Theater Group Specifications
MADE IN CHINA
CS-1X4HDSPLEXT
HOME THEATER GROUP
1 x 4 H DMI Extender Splitter
User manual
- -
- -
,.--
-
0 0
0
~ ~ .~ ~ -~•~1§£1§i]0
. I I .
I I I I
I I
. I I .
. I I .
I I I I
I I
. I I .
. I I .
I I I I
I I
. I I .
. I I .
I I I I
I I
. I I .
= @ =
,s?.@~ - ,[email protected]?-
= @ =
,s?. @~ - ,[email protected]?-
= @ =
,s?. @~ - ,[email protected]?-
= @ =
,s?. ®~ N . 2®.s?-

• IMPORTANT SAFETY INSTRUCTIONS
1. Do not mix up the Transmitter and Receiver, and the IR blaster and
IR receiver.
2. Do not plug-in/out the cables ,when it is in using.
3. Use DC SV power supply only. Make sure the specification matched
if using 3rd party DC adapters.
4. Support power from transmitter to receiver unit over the CAT6 cable.
• INTRODUCTION
This HDMI extender splitter works with 4 HDMI CAT6 extender
receivers to split and extend 1 HDMI source to 4 HDMI displays over
single CAT6/6a/7 cable up to 40m/131ft. The highest resolution
supported is 1920x1080@60Hz, and it supports IR passback, EDID pass
through and only one power adapter for the transmitter is needed,
the Receiver is powered by the transmitter over CAT6 cable. Ideal
solution for HDMI exhibition, Video conference and show center, ect.
• PACKAGE CONTENTS
Transmitter unit x lpcs
cm:::[JmID==
-==
IR blaster extension
cable xlpcs
. I I.
I I I I
! I I!
Receiver unit x4pcs
~
~
IR receiver extension
cable x4pcs
-
User Manual x lpcs
DCSV/3A xlpcs

• FEATURES
1. Distribute 1 HDMI source to 4 HDMI displays over network cable
simultaneously.
2. Support one HDMI Loop-out.
3. Compatible with CAT6/6a/7 network cables.
4. The
transmission distance is up to 40m/131ft.
5. The highest resolution supported is 1920x1080@60Hz.
6. Support 20~60Hz IR pass back.
7. Support EDID Setting function.
8. Support power from transmitter to receiver unit over the CAT6 cable.
9. Plug and play.
10.
Wall-mounted function, easy installation.
• INSTALLATION REQUIREMENTS
1. HDMI source device(computer graphics card, DVD,PS3, HD
monitoring equipment etc).
2. HDMI display device like SDTV, HDTV, and projector with HDMI port.
3. UTP/STP CAT6/6A/7 cable, follow standard IEEE-568B.
• PANEL DESCRIPTION
1. Transmitter unit (TX)
fr.)] § NPUT =• ·
t::J~O lb)i -
DC SV EDID IR OUT HDMI
1
1 2 3 4 5

CD Power input ( DCSV)
@ EDID switch
® IR signal output to connect
with blaster extension cable
@ HDMI input
2. Receiver unit (RX)
CD 0 ®
CD LENGTH: for adjusting to the length
of network cable
0 RJ45 signal input
® RJ45 indicator led it lights on all the
time with HDMI signal transmission,
flashes
with no signal transmission
l
® H DMI output
® RJ45 signal output
(J) Power/ signal indicator
® Reset button
~
@
l J 0
@DCSV
HDMIOUT IRIN@
@ ® ®
0
DVSV power input (OPTIONAL)
®
HDMI signal output
® IR signal
input to connect with
IR receiver extension cable
Remarks: The LENGTH key is
designed for switching between automatic
and manual setting to adjust cable length. Powered on without any
operation, extender works with parameter set and memorized before.
Powered on and then press LENGTH key, The first two press, it will
entering automatic mode to adapt cable length. The following 12 times
of pressing, it will entering manual mode in 12 levels to meet different
cable length. After all 12 levels of press, it will entering auto mode
again and into next loop.

• Installation Procedures
1. How to make a CATS/SE/6 network cake
Follow the stanard of IEEE-568B:
1- Orange/white
3- Green/white
5- Blue/white
7- Brown/white
2. Connection
2- Orange
4- Blue
6- Green
8- Brown
DVD
6vo
I
l HDMI input
HDMI extender splitter
HDMIOut
TV
i --+-
@)
TV
Cable
TV
Receiver
Remarks: Please do not remote control two or RX units ' IR cable at the same time,
which to avoid interference .

3. Connection instruction:
1) Connect the HDMI signal source device to the Transmitter HDMI
input port with HDMI cable.
2) Connect IR blaster to EXTENDER IR OUT
3) Connect the Transmitter RJ45 port to HDMI EXTENDER RX's Rj45
input port by network cable.
4) Connect HDMI EXTENDER RX's HDMI output port to HDMI display's
HDMI input port by HDMI cable and set the HDMI display's signal
source to be H DMI port.
5) Supply the power(Power's signal light is red, when there are signal
input then the power light is blue),the product will work.
4.EDID Setting
1) H DMI source device reads the EDID information of the transmitter
(TX) and then output the relative HDMI signal format.
2) There are 8 build-in EDID status, and others could be selected by
the EDID switch in the HDMI extender splitter(transmitter), the
detail Setting Information shown as below:
Switch UP: use the Arabic numeral "1" to represent
Switch DOWN :
use the Arabic numeral "O" to represent
SWl
SW2 SW3
EDID Mode
0 0 0
720P@50Hz 2.lCH
1 0 0
720P@50Hz 7.lCH
0 1 0
1080i@60Hz 2.lCH
Switch
Status
1 1 0 1080i@60Hz 7.lCH
0 0 1
1080P@60 2.lCH
1 0 1 1080p@60Hz 7.lCH
0 1 1 Read Loop-out(if
not connect
the loop-out show default)
1 1 1
Default 720P@50Hz 2.lCH

• FAQ
Q: No image or audio output on display?
A: 1) Please check whether display on standby mode;
2) Please check whether display HDMI signal channel in accord with
HDMI input port;
3) Please check whether " LINK" LED on RX side keeps on, LED flash
means
RX does not receive signal from TX;
4) Please check
whether signal indicator LED on TX turns blue,
LED on red means no input signal;
5) Please check whether input resolution supported by this product.
Q: Image unstable?
A: l)Press the "LENGTH" or "RESET" button on the transmitter to
re-identify the signal;
2) Please pull & plug CAT cable on corresponding port to reconnect.
Q: Only partial ports have output?
A: 1) Please check whether CAT cable or HDMI cable connected
correctly;
2) Press the "LENGTH" or "RESET" button on the transmitter to
re-identify the signal;
3) Please pull & plug CAT cable on corresponding port to reconnect.
• SPECIFICATION
Items Specifications
HDMI signal HDMil.3, Compatible with HDCPl.2
Input
1 x HDMI
Output
4 x RJ45
Support resolutions 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz,
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
Transmit distance Full HD resolution 1080p@60Hz up
to 40 meters
via
CAT6 cable
IR signal Support 20~60kHz IR device

EDID
Support EDID setting function
Working temperature
0°C ~ 60°(
Power supply DCSV/3A
Power Consumption
<lSW
Dimension
TX: 190(L) x 95.9(W) x 23.9(H) mm
RX: 71.6x 66.6x 22.6mm
Color Black
Disclaimer
The product name and brand name may be registered trademark of related
manufacturers.TM and ® may
be omitted on the usermanual. The pictures
on the usermanuaIare
just for reference,and there may be some slight
difference withthe
real products.
We reserve the rights
to make changes without further notice to aproduct
or system described herein to improve reliability, fun ct ion or design.

SALES 866-839-9187