Meyer V-71 QUIK LIFT User manual

PARTS & INSTALLATION INSTRUCTIONS
V-71 QUIK LIFT®
PART LIST
Form 1-1031
June 2011
Parts indented are included in the carton, bag or assembly under which they are indented.
© 2011 Printed in the U.S.A.
Meyer Products LLC.
18513 Euclid Ave. • Cleveland, Ohio 44112-1084
Phone [phone] (Area Code 216)
www.meyerproducts.com• email [email protected]
Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details,
specifications and prices without notice or without incurring any obligation.
Item Part No. Qty. Description
15130 1 V-71 Lift and P.A. Ass'y. (Complete) 12 volt
1 15132 1 •V-71 Lift Ass'y. (Unit only) 12 volt
2 15633 1 •• Cover
3 05815 1 • Lift Cylinder 1.75 x 8" SAE-6
4 22883 1 • Hose 1/4 x 22" SAE 6
07713 2 • Double Acting Wing Ram with Fittings & Hoses
5 05756 2 •• Double Acting Ram 1.25" x 12" SAE-6
6 22884 2 •• Hose 1/4 x 33" M-6 x Flat Face Seal
7 22886 2 •• Hose 3/8 x 22" M-6 x Flat Face Seal
8 22866 4 •• Elbow 90 SAE 6 Face Seal/Adapter
9 22696 1 • Super Vee Plow Side Harness
10 22691 1 • Universal Truck Side Harness
11 05024 1 • Power Cable
12 22869X 1 • V-71 Controller w/HFP
13 15370 1 • Starter Solenoid - 12 Volt
08366 1 • Hardware Bag 15130
14 15634 1 •• Cover Strap
15 20029 4 •• Bolt H 5/16-18 x 1-1/2" Gr. 2
16 20049 2 •• Bolt H 3/8-16 x 1" Gr. 2
17 20152 4 •• Bolt H 5/8-11 x 5” Gr. 5
17A 20153 2 •• Bolt H 5/8-11 x 5-1/2” Gr. 5
18 20304 4 •• Locknut 5/16-18
19 20309 4 •• Locknut 5/8-11
20 20327 2 •• Lockwasher 3/8"
21 21398 2 •• Self Tapping Screw 1/4-14 x 3/4"
22 22866 1 •• Elbow 90 SAE 6 Face Seal/Adapter
23 22868 5 •• Straight Fitting SAE-6 Face Seal/Adapter
08202 1 • Hardware Bag Plug Bracket
24 19607 1 •• Plug Bracket
25 19609 1 •• Plate
26 20027 2 •• Bolt H 5/16-18 x 1 Gr. 2
27 22658 2 •• Bolt H 5/16-18 x 3 Full Thread Gr. 2
28 20326 4 •• 5/16 Lockwasher
29 20525 4 •• 5/16-18 Finish Nut
30 13333 1 • V-71 Mounting Bracket
15134 3 • M-1 Hydraulic Fluid Quart

GENERAL INFORMATION
CAUTION: Always disconnect battery prior to installation.
SAFETY PRECAUTIONS should be used when Quik Lift® is in a
RAISED position. LOWER plow to the ground when vehicle is
PARKED.
OVERHAUL and SERVICE information is covered on separate
instructions.
Note:
1. Connect ground cable to negative side of battery for a solid
connection to ground.
2. Caution: Route all cables away from moving engine parts,
Manifolds, and sharp sheet metal.
3. For weather protection, tape all electrical connections at front of
vehicle.
4. The vehicle must be equipped with a "Heavy
Duty Battery" (70 Amp, Hr. Min.), 550 C.C.A. and "Alternator"
(60 Amp. Min.) to obtain maximum performance.
5. Follow these instructions explicitly. Warranty does not apply to a
Meyer product which has been negligently or improperly
assembled or installed.
Fig. 1
ADDITIONAL BATTERY CONNECTIONS
a. When attaching cables to battery with side post terminals, use
M.P. Adaptor Part #21976 and attach as shown in Figure 3.
b. Figure 3 illustrates the method of using a repair type terminal
connector which is original equipment on some vehicles.
Hydraulic Solenoid Color Code:
OPERATION - SOLENOID COMBINATION
RAISE - Motor Solenoid + S6
LOWER - S1
LEFT ANGLE - Motor Solenoid + S3 + S5 + S8
LEFT EXTEND - Motor Solenoid + S2 + S7
LEFT RETRACT - Motor Solenoid + S3
RIGHT ANGLE - Motor Solenoid + S2 + S4 + S7
RIGHT EXTEND - Motor Solenoid + S5 + S8
RIGHT RETRACT - Motor Solenoid + S4
SCOOP - Motor Solenoid + S2 + S5 + S7 + S8
VEE - Motor Solenoid + S3 + S4
COIL COLOR CODE
MOTOR SOLENOID - WHITE WIRE
S1 - RED WIRE
S2 & S7 - BLACK WIRE
S3 - GREEN WIRE
S4 - YELLOW WIRE
S8 & S8 - BLUE w/WHITE STRIPE
S6 - PURPLE WIRE
GROUND WIRE EACH COIL BLACK W/WHITE STRIPE
Figure 1
Figure 2
Figure 3
Drain
Fill
S1
S2
S3
S4
S5
S6
S7
S8
Lift
Cylinder
Hose
Port
Pass Side
Live End
(1/4 Hose)
Driver Side
Live End
(1/4 Hose)
Pass Side
Fixed End
(3/8 Hose)
Driver Side
Fixed End
(3/8 Hose)
1
2
3
4
5
6
78
10
11 12
13
14
14
15 16
17
18
19
20
21
22
24
25
26
27
28
29
30
6
7
9 (See Figure 2)
8
5
8
8
17
17
17
19
Keyed Ignition (Blue)
Light Module "C" Harness
Light Module "B" Harness (Orange)
Red
Red
Black
White
Blue Wire
Light Module "C" Harness
(Reverse
Signal)
HFP
Black/White
Stripe
28
29
23
23
V-71 mounting bracket
mounts outside of
Lift Frame

For snow plow light installation see separate instructions.
Orange wire on Harness (10) will attach to both orange wires of
the "B" harness supplied in the Light Module Kit. Reference
Form 1-757
Route Cables “C” (Yellow) from module to Harness (10). Connect
both “C” Harness female ends to the male corresponding ends
of the Harness (10).
Connect both male ends from the snow plow light to the female
ends on the Super-V Plow Side Harness (9).
Check snow plow light blinkers to make sure the wires have not
been reversed.
Note: All electrical connections should have both ends coated
with a dielectric grease prior to final installation. This will ensure
a good connection and help in preventing corrosion.
K. Refer to Operation and Maintenance Manual for complete
controller operation.
L. After all electrical connections have been made the drop speed
of the plow may be evaluated / adjusted. To adjust, loosen up
the hex nut and adjust in to slow the drop speed and out to
make it faster. After ideal drop speed it achieved, retighten the
hex nut. See Figure 4.
After cycling of the plow, recheck oil level.
INSTALLATION INSTRUCTIONS
A. Install the V-71 Mounting Bracket (30) to the Lift Frame and
Light Bracket (passenger side) from the CLF Carton using
5/16-18 x 1-1/2" Bolts (15) and 5/16-18 Locknuts (18). Install the
V-71 Lift Assembly (1) to V-71 Mounting Bracket Assembly (30)
using Bolt H 3/8-16 x 1" (16) and 3/8 Lockwasher (20).
B. Attach Lift Arm packed in the CLF Carton to Lift Frame using
Bolt H 5/8-11 x 5-1/2" and 5/8-11 Locknut. Attach the Lift Cylinder
(3) to the Lift Arm using Bolt H 5/8-11 x 4-3/4" and 5/8-11 Locknut.
Attach the Lift Cylinder (3) to the Lift Frame using Bolt H 5/8-11
x 3-1/4" and 5/8-11 Locknut. Attach elbow (22) to V-71 Lift
Assembly and attach Straight Fitting (23) a to Lift Cylinder (3).
Attach hose (4) to Straight Fitting (23) and then to elbow (22).
WARNING: Lift arm should be removed from vehicle if /
when snow plow is removed.
C. Attach fixed end of Wing Cylinders (5) to the
A-Frame with a 5/8-11 x 5" bolt (17) and 5/8-11 locknut (19) on
each side.
D. Attach live end of Wing Cylinder rod (5) to the Wings using a
5/8-11 x 5" bolt (17) and 5/8-11 locknut (19) on each side. Use
5/8-11 x 5-1/2" bolt (17A) on the SVLD Wings
E. Attach 4 Straight Fittings (23) to the bottom of the V-71 PA
Block.
F. Attach wing cylinder hoses to Straight Fitting (23). Thread hose
face seal fittings onto the adapters hand tight. Then tighten
locking nut another 30 to 45 degrees of rotation. See Figure 2.
See Figure 5 for hose roouting and fitting angles. Use zip
ties to secure and route hoses to avoid contact with moving
parts of the plow assembly.
G. Run Universal Truck Side Harness (10) through a hole in grille
and into the engine compartment. Sandwich vehicle grill
between Plug Bracket (24) and Plate (25) using Bolt H 5/16-18
x 3" (27), 5/16 Lockwasher (28) and 5/16-18 Finish nut (29).
Secure Universal Truck Side Harness (10) to Plug Bracket (24)
using Bolt H 5/16-18 x 1" (26), 5/16 Lockwasher (28) and
5/16-18 Finish nut (29).
Caution: Secure Universal Truck Side Harness (10) from
any hot / moving parts with tie wraps as needed.
H. Drill a 1-1/4" Diameter Hole thru firewall to extend the harness
into the cab of the vehicle. Fused lead from Universal Truck
Side Harness (10) must be attached to terminal in fuse panel
that is activated only when the ignition key is "on."
I. Install Motor Solenoid (13) to metal surface in engine
compartment using Self Tapping Screws (21). (Solenoid must
be grounded to operate). Attach Red Power Cable (10) to a
large terminal on Motor Solenoid (13). Attach Black Ground
Cable (10) to negative (-) terminal of battery. Attach Red Power
Cable (11) to positive (+) terminal of battery and remaining
large terminal on Motor Solenoid (13). Attach small white wire
from harness (10) to small terminal (S) on Motor Solenoid (13).
Attach small Black/white stripe wire from harness (10) to small
terminal (I)(ground) on Motor Solenoid (13) Attach Blue wire to
a reverse signal on the vehicle. The blue wire is sensing when
the vehicle is in reverse in order to operate HFP (Hands Free
Plowing).
J. Add Meyer M-1 Hydraulic Fluid to reservoir and bleed the
Wing Cylinders, proceed as follows:
a. Remove Fill Plug from reservoir to add fluid during charging.
b. Operate the Wing cylinders (5), one at a time in both directions,
until they are filled with Meyer M-1 Hydraulic Fluid and are not
spongy.
c. Top off the unit to the fill line on the reservoir with Meyer M-1
Hydraulic Fluid.
NOTE: Proper fluid level is to the fill line on the reservoir. It
must be checked with the lift and both wing cylinders fully
retracted.
Figure 4
Figure 5
Lower
A
djustment
Screw
(
+
)
(-)