MGE UPS Systems Pulsar EXtreme CLA 2000 VA User manual

ИБП MGE Pulsar EXtreme - Pulsar EXtreme CLA 2000 - 3000 ВА - Руководство
Постоянная ссылка на страницу: https://eaton-power.ru/catalog/mge-pulsar-extreme/

51033775EN/AA - Page 1
www.mgeups.com MGE UPS SYSTEMS
Pulsar
EXtreme CLA
2000/3000 VA
Installation manual
N
O
T
H
I
N
G
W
I
L
L
S
T
O
P
Y
O
U
N
O
W

Page 2 - 51033775EN/AA

51033775EN/AA - Page 3
... and checking the contents
1. Unpacking
Pulsar EXtreme CLA 2000/3000 VA
Tower model
Rack model
Pulsar EXtreme CLA module.
connection cable.
1
2
documentation.
telescopic rails and 19" rack mounting hardware.
3
4
1
2
3
1
3
2
4

Page 4 - 51033775EN/AA
Mounting the rails in the rack.
The rails and the screws required to mount them are included in the box.
2.1 Mounting (Rack model)
2. Installation
1
2
3
33
3
4

51033775EN/AA - Page 5
2.2 Checking equipment compatibility
Check that the UPS and CLA modules are compatible:
UPS no.
Pulsar EXtreme CLA 2000 51033021
Pulsar EXtreme CLA 3000 51033031
CLA no.
51033029
51033539
2.3 Batteries to be used
Use only 12 V / 65 Ah lead-acid batteries.
Connect them as indicated below to obtain the required backup time:
2 hours
Pulsar EXtreme CLA 2000 1 string of 7
12V / 65Ah batteries
4 hours 8 hours
2. Installation
2 parallel-connected strings of 7
12V / 65Ah batteries
3 parallel-connected strings of 7
12V / 65Ah batteries
Backup time
This operation may be carried out only by qualified electricians using the necessary safety equipment for work on live parts
(insulated tools, gloves, goggles).
The connection of each module to the electrical supply must be protected by an easily accessible circuit
breaker (not supplied). A module can be isolated from the electrical supply by opening this circuit
breaker.
Before making any connections or working on the equipment, make sure the battery circuit breaker is in OFF
position and that the main contacts of the upstream protective devices of the electrical installation are open (OFF
position).
For maximum battery life, CLA and UPS modules must be installed in the same room as batteries so that the automatic
regulation of the charge voltage as a function of temperature can work correctly.
Pulsar EXtreme CLA 2000 Rack 51033521 51033529
Pulsar EXtreme CLA 3000 Rack 51033531 51033539
Pulsar EXtreme CLA 3000 1 string of 10
12V / 65Ah batteries
2 parallel-connected strings of 10
12V / 65Ah batteries
3 parallel-connected strings of 10
12V / 65Ah batteries
2.4 Connecting the batteries to the Pulsar EXtreme CLA module

Page 6 - 51033775EN/AA
2. Installation
L +
BATTERIE/BATTERY
L -
4
2
25A
t
In
B
1
10
90
20
3
25A
12V-65Ah
5
Use a 3-conductor cable (shielded, max.
length 6 m, 3 x 4 mm2conductors) to be
passed through the shielded cable gland.
Use a 25 A circuit breaker
(curve B) for protection.
Note: the cable and circuit breaker are not
supplied with the product.
1. Prepare the cable.
2. Unscrew the plate and dismantle the
metal cable gland on the Pulsar EXtreme
CLA module.
3. Mount the cable gland on the shielded
cable.
4. Connect the 3 conductors to the terminal
block and refit the plate.
5. Connect the other end of the cable to the
circuit breaker.
2.5 Connecting the Pulsar EXtreme CLA module to the power source
10
50
1
L +
RESEAU/MAINS/NETZ
N
3
2
+
Use a flexible cable (3 x 2.5 mm2
conductors) to be passed through the plastic
cable gland.
Always connect the earth wire
first. Use a 10 A circuit breaker
(curve C) for protection.
Note: the cable and circuit breaker are not
supplied with the product.
1. Prepare the cable.
2. Unscrew the plate with the plastic cable
gland.
3. Connect the 3 conductors and remount
the plate.

51033775EN/AA - Page 7
2. Installation
2.6 Connecting the UPS to the Pulsar EXtreme CLA module
Use the connection cable supplied with the
module.
2.7 Setting the UPS
Before connecting the loads to be protected
and starting the system, the UPS must be
reconfigured using the UPS Driver software
supplied on a diskette with the UPS.
1. Switch the battery circuit breaker to ON
position.
2. Connect a PC to the UPS using an RS232
cable.
3. Run the UPS Driver software installed on
a diskette. Go to the "battery" menu and
select the battery backup time (2, 4 or 8
hours) corresponding to the new
configuration.
Once the backup time has been set, click to
save the settings and exit UPS Driver. This
procedure is necessary for fast recharge of
the batteries by the Pulsar EXtreme CLA.
The installation is now ready and you can
connect the equipment to be protected.
+
ON
2
3
50A
12V-65Ah
25A
1

Page 8 - 51033775EN/AA
Weight in kg
10
14
Dimensions and weights
3. Technical specifications
Pulsar EXtreme CLA
Tower model
Rack model
0.75 x Pn 0.5 x Pn
Dimensions in mm (H x W x D)
443 x 173 x 465
177(4U) x 483 x 462
Rated
power (Pn)
2-hr CLA
4-hr CLA
8-hr CLA
2 hrs 10 min
5 hrs
8 hrs
3 hrs
6 hrs 30 min
12 hrs
4 hrs 50 min
12 hrs
18 hrs
Recharge time
(to 90% full backup time)
2-hr CLA
6 hrs
4-hr CLA 8-hr CLA
12 hrs 21 hrs
Operating voltage and frequency of the Pulsar EXtreme CLA
Battery backup times
Voltage: 160 to 260 V.
Frequency: Same as that of the UPS.
Recharge time and current
The total recharge current is 9.5 A whatever the configuration.