MGE UPS Systems EX 11RT User manual

www.mgeops.com
EX RT Transformer Module
Quick Start
Standard Features
◗When used with standard
system, EX RT Transformer
Module provides isolated
and Step-down 120/208/
240 Vac outputs.
◗Multiple Output receptacles:
120/208/240 Vac.

Quick Start
186-86000-03 B00
STEP 1 EX RT Transformer Module Unpacking and Parts Check
STEP 2 EX RT Transformer Module Tower Configuration
EX RT Transformer Module Quick Start
Warranty and
Product Registration
EX RT Transformer
Quick Start Manual
EX RT Transformer Module Box Contents
Tower Stand Extenders
Stabilizer Bracket
(4 screws included)
41
Transformer
Rail Kit
Transformer
Cable
www.mgeops.com
EX 5/7/11RT Systems
Quick Start
Tower Configuration of Standard System with Transformer Module
Transformer Module
EX11RT
EXB11 RT
Power Module
Battery
Module
(up to 6)
Power Module
Battery Module
Transformer Module
5
1
1
2
2
4
4
4
4
33

EX RT Transformer Module
STEP 3 Rack Configuration
See EX 5/7/11RT Systems Installation and User Manual for details.
EX RT Transformer Module Quick Start
OFF
O
OFF
O
OFF
O
OFF
O
EX RT Transformer
EX RT Transformer
EX11RT
OFFON
EX11RT
OFFON
EX11RT
OFFON
EX11RT
OFFON
1
2
3
FINISHED PANEL
(rack orientation)
1
2
3
A. Prepare the power module front panel logo and LCD display for
rack orientation. Apply to all modules. (Power Module shown.)
Stack-up sequence in Rack configuration
OFFON
EX 11 RT
2. POWER MODULE
(upper, EX 5/7/11 RT)
1. EX RT Transformer
Module (Top)
EX RT Transformer
3. BATTERY MODULE
(lower, EXB 5/7/11 RT)
4. BATTERY MODULE
(bottom, EXB 5/7/11 RT)
(Shown with power module and 2 battery modules)
B. Rack Installation
3
4
4
4
4
2
2
1
4
4
5
1
66
6
1. Attach both front mounting ear
brackets to module with supplied
screws. (For this step,it is possible to
adjust the position of both front
mounting brackets.)
2. Attach rear support brackets to
module. These brackets prevent the
module from sliding out of the rack.
3. Attach rails together and secure with
wing nuts, and finger tighten. (both
sides).
4. Attach both rails to rear and front of
rack with supplied flathead screws (as
shown).
5. Use caution when sliding unit into rack.
Temporarily secure unit to rack with
thumb screws on front mounting
brackets.
6. Secure rear support brackets to rails.
OFF
O
OFF
O
6
OFF
O
286-86000-03 B00

Quick Start
386-86000-03 B00
STEP 4 Systems Connections
EX RT Transformer Module Quick Start
EX RT Transformer Module, Power Module, and Battery Module Connections
System Connections with Transformer Module
AC Normal INPUT Transformer OUTPUT TO LOAD
Battery Module
EXB 5/7/11RT
Power Module
EX 5/7/11 RT
Transformer
Module EX RT
Transformer
Main Output
Circuit Breaker
Follow connection
diagram for appropriate
input/output voltages.
Connection Diagram
(bottom of Transformer I/O Box)
L3 L2 L1 Lb Ld N Lc La
208Vac
240Vac
AC Input
120Vac
208Vac
AC Output
120Vac
240Vac
Transformer Module Terminal block capacity:
maximum 4 AWG solid or stranded wire on
transformer module.
1. Check that the battery circuit breaker is OFF (“0”) position.
2. Connect the battery power cable to the connectors of the power and battery modules,
3. Connect the battery detection cable between connectors of the power and battery modules.
4. Turn on battery module circuit breaker, power module, I/O Box, circuit breaker, and Transformer Module
Main Output Circuit Breaker.
5. Push ON button on the Power Module for more than 3 seconds.
Battery Module
Circuit Breaker
Battery Power
Cable
Power Module
Connector
Battery Detection
Cable
1
2
3
Power Module Circuit Breaker
4
4
See EX 5/7/11RT Systems Installation and User Manual for initial start-up procedures.

13 Whatney, Suite #101, Irvine, California 92618 • www.mgeops.com
www.mgeops.com
Contact MGE Office
Protection Systems
United States
MGE Office Protection Systems
13 Whatney, Suite #101
Irvine, CA 92618
[phone]
www.mgeops.com