Micro Innovations Micro Webcam Matrix User manual

Micro Webcam Matrix
Users Manual

FCC STATEMENT
IC445C
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turningtheequipmentoffandon,the
user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult a service representative for help.
Properly shielded and grounded cables and connectors must be used in order to comply with FCC emission limits. Micro Innovationsisnot
responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes
or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.
Responsible party:
Micro Innovations
400 Clearview Ave.
Edison, NJ 08837
Telephone: [phone]
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de classe B est conforme à la norme NMB-003du
Canada.

TABLE OF CONTENTS
WELCOME…………………………………………………………........ PAGE 3
INSTALLING THE CAMERA…………………………………............. PAGE 4-5
TROUBLESHOOTING AND TECHNICAL SUPPORT……………... PAGE 6
HELPFUL HINTS……………........................................................... PAGE 7-8
WARRANTY INFORMATION………………………………............... PAGE 9

Welcome
Congratulations onthe purchase of your new Micro InnovationsWebcam Matrix.
This manual will help guide you through the setup process and answer any
questions you may have regarding your webcam.
Package Contents
•Micro Webcam Matrix
•USBConnector
•Warranty Information
•User’s Manual
•CD-ROM with Driver
System Requirements
•Pentium IBM or 100% Compatible PC
•Windows ME/2000/XP
•Available USB Port
•Available CD-ROM Drive

INSTALLING THE CAMERA
NOTE: Please insert the CD-ROM and install the driver and software
before plugging in the camera!
Software Installation
STEP 1-Insert the CD into your CD-ROM drive. TheSetup Wizard will
appear on your computer screen. Note: If theSetup Wizard does not
appear, click Start and select Run. Type<Drive Letter>:\Setup and press
Enter. (Example: if the disk is in drive D, you would typeD:\Setup)
STEP 2–Follow the onscreen instructions to install the driver and software
applications. There are several software applications included on theCD. You
can install any or all of them easily during this phase of the software installation.
Note:If you are installing this device running Windows XP, you may encounter a
notification stating thatthis device has not passed Windows XP Logo Testing.
Select Continue Anywayto complete the installation.
STEP 3–When the software installation is complete, click Finish to close
the installation program.

Hardware Installation
STEP 1-Insert the USB connector into an available USB port or hub located
on your computer.
STEP 2–A Found New Hardware wizard will appear. Follow the onscreen
instructions, clicking Next to install the hardware.
Note:If you are installing this device running Windows XP, you may encounter a
notification stating thatthis device has not passed Windows XP Logo Testing.
Select Continue Anywayto complete the installation.
Continue to follow the on-screen prompts until your camera installation is
complete. Click Finish to close the wizard.
Camera Care
Keep all beverages away from the camera working area and avoid any spills.
Maintaining your MicroWebcam Matrixwill ensure longer life and will minimize the
chances of causing damage to your camera and computer. There are no user
serviceable parts. Only Micro Innovations may service or repair this product.

Troubleshooting
•If your camera is not recognized in Windows, be sure to check that the USB
connector is securely connected into the back of your computer. You may
have installed the driver with the camera plugged in. Uninstall the driver,
unplug the camera, and then reinstall the driver. Then reinstall the camera
hardware as directed in the Hardware Installation section.
•You may have connected your camera while the computer was turned off.
Turn your computer on,and disconnect and reconnect the USB connector.
•Windows 95 and Windows NT users: These operating systems do not
support USB. This camera is not compatible with Windows 95 or Windows
NT. This camera model is also not supported in Windows 98/98SE.
Technical Support and Service
For technical assistance call toll free: 1(877) 550-5534 or visit our website:
www.microinv.com.
Technical Support Hours of Operation: Monday –Friday, 8:30am–7:00pm Eastern
Standard Time.

Helpful Hints
The following hints will help you achieve the best results with your Micro
Webcam Matrix:
Camera placement
•Position the camera so that the subject is centered.
•Place the camera on a steady surface.
Lighting
•Use sufficient lighting.
•Place the light source behind the camera and facing the subject.
•Maintain a consistent lighting environment, i.e. do not mix fluorescent
lighting and other lighting types.

Focus
•For a sharper image, adjust the focus of your Micro Webcam Matrixby
rotating the focus ring located on the front of your camera.
Maintenance
•Keep the camera away from moisture and extreme temperature.
•Never use harsh or abrasive cleaners or organic solvents on the
camera or on any of its parts.
•Never disassemble or touch the inside of the camera.
To Clean Your Camera Lens
•Blow gently on the lens to remove any dust and/or dirt.
•Wipe the lens gently with a soft lint-free cloth or an unthreaded lens-
cleaning tissue.
•Do not use a cleaning solution unless it is designed specifically for
camera lenses.
•Do not wipe the camera lens with chemically treated eyeglass lens
tissues as they may scratch the lens.

WARRANTY INFORMATION
Charge to the purchaser for parts or labor for the time periods.
This warranty does not apply to a ny appearance items of the product nor to the additional excluded item set forth below nor to any product
the exterior of which has been damaged or defaced which has been subjected to misuse, abnormal service or handling or which has been
altered or modif ied in design or construction.
The limited warranty described herein is in addition to law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OFMERCHANTABILITY AND
FITNESS FOR USE ARE LIMITED TO THE PERIOD FROM THE DATE OF ORIGINAL PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neitherthesalespersonnelofthesellernoranyotherpersonisauthorizedtomakeanywarrantiesotherthanthosedescribedherein or to extend the duration
ofanywarrantiesbeyondthetimeperioddescribedhereinonthebehalfofMicroInnovations.
The warrantiesdescribedhereinshallbethe soleand exclusivewarranties grantedby MicroInnovations andshall bethe soleand exclusive remedy available to
thepurchaser corrections of defects, in the mannerand for the period of time describedherein, shall constitute complete fulfillment of allliabilities and responsibilities of Micro
Innovationsto the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract negligence, strict liability or otherwise. In no event
shallMicro Innovations be liable or in any way responsible, for any incidental of consequential economic or property damage. Some states do not allow the exclusion of incidental or
consequentialdamages, so the above exclusion may not apply to you.
Thiswarranty gives you specific legal rights. You may also have other rights, which vary from state to state.
WarrantyPeriod: Lifetime on parts and labor from date of purchase
Whereto ship: Micro Innovations, 400 Clearview Ave, Edison NJ 08837
Enclose$5.95 for Shipping and Handling.