MicroElektronika Temp&Hum click User manual

2 3
click
BOARD™
www.mikroe.com
2. Soldering the headers
3. Plugging the board in
Once you have soldered the headers your
board is ready to be placed into the desired
mikroBUS™socket. Make sure to align the cut
in the lower-right part of the board with the
markings on the silkscreen at the mikroBUS™
socket. If all the pins are aligned
correctly, push the board all the
way into the socket.
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder the
pins carefully.
Turn the board upside down so that
the bottom side is facing you upwards.
Place shorter pins of the header into the
appropriate soldering pads.
Before using your click board™, make sure
to solder 1x8 male headers to both left and
right side of the board. Two 1x8 male headers
are included with the board in the package.
4. Essential features
Temp&Hum click has temperature
measurement accuracy is ±1°C within a
0-60°C range. The precision is increased to
±0.5°C in a narrower range from 15 to 40°C.
The relative humidity measurement range is
from 0 to 100% with ±6% accuracy (or ±4.5
in 20-80% range) The measurements are
outputted in a 16-bit resolution.
1
Temp&Hum click carries ST’s HTS221
temperature and relative humidity sensor.
The chip comprises a capacitive sensing
element and a 16-bit ADC. The board
communicates with the target MCU through
mikroBUS™ I2C interface (SCL, SDA),
with an additional interrupt (INT) which
you can set as an alarm when a specied
temperature or humidity value is reached.
Designed to use a 3.3V power supply only.
Temp&Hum click
1. Introduction
Temp&Hum click Manual v100
0100000084311

R1
2K2
LD1
AN
RST
CS
SCK
MOSI
MISO
+3.3V
GND
PWM
INT
RX
TX
SCL
SDA
+5V
GND
MIKROBUS DEVICE CONN.
VCC-3.3VVCC-3.3V
INT
SCLSDA
SCL
R2
4K7
VCC-3.3V
VDD
DRDY
SDA
CS
GND
SCL
U1 HTS221
SDA
VCC-3.3VVCC-3.3V
INT
R3
4K7
VCC-3.3V
C1
100nF
VCC-3.3V
8. Code examples
MikroElektronika oers free tech support
(www.mikroe.com/support) until the end of
the product’s lifetime, so if something goes
wrong, we’re ready and willing to help!
Once you have done all the necessary
preparations, it’s time to get your click board™
up and running. We have provided examples
for mikroC™, mikroBasic™and mikroPascal™
compilers on our Libstock website. Just
download them and you are ready to start.
.com
6. Dimensions
MikroElektronika assumes no responsibility
or liability for any errors or inaccuracies
that may appear in the present document.
Specication and information contained in
the present schematic are subject to change
at any time without notice.
Copyright © 2015 MikroElektronika.
All rights reserved.
mm mils
LENGTH 28.6 1125
WIDTH 25.4 1000
HEIGHT* 3 118
5. Schematic
7. Temp&Hum alternatives 10. Disclaimer
9. Support
25.4 mm / 1000 mils
28.6 mm / 1125 mils
We have a wide range of temperature and
humidity sensors in our click board range.
For alternatives, visit:
http://www.mikroe.com/click
* without headers